Electropolishing and passivation of NiTi shape memory alloy

Electropolishing of NiTi alloy has been investigated. The influence of polishing bath composition and the operating conditions instead of the conditions of the process on the quality of the surface, evaluated by AFM and SEM methods, was established. Morphologically uniform surfaces were obtained only in the case of solutions containing hydrofluoric and sulfuric acids. Electropolished samples were sterilized and thermally passivated, then their corrosion resistance was measured in Tyrode's physiological solution. It was established that already after the electropolishing the corrosion resistance of NiTi alloy increases due to the spontaneously formed TiO₂ layer. The increase of the thickness of the layer during sterilization and thermal passivation causes further increase in the corrosion resistance.     

Dielectric,Mechanical, and Thermal Properties of Low-Permittivity Polymer–Ceramic Composites for Microelectronic Applications

A new low-permittivity polymer–ceramic composite for packaging applications has been developed. The ceramic-reinforced polyethylene and polystyrene composites were prepared by melt mixing and hot molding techniques. Low-loss, low-permittivity Li₂MgSiO₄ (LMS) ceramics prepared by the solid-state ceramic route were used as the filler to improve the dielectric properties of the composites. The relative permittivity and dielectric loss were increased with the increase in the ceramic loading at radio and microwave frequencies. The mechanical properties and thermal conductivity of the Li₂MgSiO₄-reinforced polymer–ceramic composite were also investigated. The stability of the relative permittivity of polymer–ceramic composites with temperature and frequency was investigated. The experimentally observed relative permittivity, thermal expansion, and thermal conductivity were compared with theoretical models.     

Congener-specific carbon isotopic analysis of technical PCB and PCN mixtures using two-dimensional gas chromatography-isotope ratio mass spectrometry

Analysis of stable carbon isotope fractionation is a useful method to study the sources and fate of anthropogenic organic contaminants such as polychlorinated biphenyls (PCBs) in the environment. To evaluate the utility of carbon isotopes, determination of isotopic ratios of 13C/12C in source materials, for example, technical PCB preparations, is needed. In this study, we determined delta13C values of 31 chlorobiphenyl (CB) congeners in 18 technical PCB preparations and 15 chloronaphthalene (CN) congeners in 6 polychlorinated naphthalene preparations using two-dimensional gas chromatography-combustion furnace-isotope ratio mass spectrometry (2DGC-C-IRMS). Development of 2DGC-IRMS enabled improved resolution and sensitivity of compound-specific carbon isotope analysis (CSIA) of CB or CN congeners. Delta13C values of PCB congeners ranged from -34.4 (Delors) to -22.0/1000 (Sovol). Analogous PCB preparations with similar chlorine content, but different geographical origin, had different delta13C values. PCB preparations from Eastern European countries--Delors, Sovol, Trichlorodiphenyl, and Chlorofen--had distinct delta13C values. PCB mixtures showed increased 13C depletion with increasing chlorine content. Delta13C values for individual CB congeners varied depending on the degree of chlorination in technical mixtures. Delta13C values of CN congeners in Halowaxes ranged from -26.3 to -21.7/1000 and these values are within the ranges observed for PCBs. This study establishes the range of delta13C values in technical PCB and PCN preparations, which may prove to be useful in the determination of sources of these compounds in the environment. This is the first study to employ 2DGC-IRMS analysis of delta13C values in technical PCB and PCN preparations.     

A microporous and high surface area active carbon obtained by the heat-treatment of chitosan

A method is described for converting chitosan into a high surface area and porous active carbon using a Na₂CO₃ solution impregnated into a partly depolymerized, protonated and water soaked chitosan. The wet chitosan paste is heat treated and transformed into a nonporous solid i.e. a carbon-rich matrix with uniformly suspended Na₂CO₃ nanocrystallites. Subsequent HCl etching opens cavities in the matrix due to the removal of the Na₂CO₃. The active carbon is high surface area (above 400 m²/g), microporous (below 1 nm) and nitrogen-rich (above 6% atomic).     

Nanoindentation of WC–Co hardmetals

WC–Co cemented carbide has been investigated using instrumented indentation with maximum applied loads from 0.1 to 10 mN. The hardness and indentation modulus of individual phases and the influence of crystallographic orientation of WC on the hardness and indentation modulus have been studied. The hardness of the Co binder was approximately 10 GPa and that of WC grains up to 50 GPa with relatively large scatter under the indentation load of 1 mN. Investigation of the role of crystallographic orientation of WC grains on hardness at 10 mN load revealed average values of H_ITbasal = 40.4 GPa (E_ITbasal = 674 GPa) and H_ITprismatic = 32.8 GPa (E_Itprismatic = 542 GPa), respectively. The scatter in the measured values at low indentation loads is caused by the effects of surface and sub-surface characteristics (residual stress, damaged region) and at higher loads by “mix-phase” volume below the indenter.     

Microwave plasma‐initiated grafting of acrylic acid on Celgard 2500 membrane to prepare alkaline battery separators—Characteristics of process and product

A process of plasma‐initiated grafting of acrylic acid on commercial porous polypropylene membrane was studied. The influence of parameters of the plasma (power, gas pressure, time plasma‐sample distance, sample arrangement) and grafting (solvent composition, monomer concentration, time, inhibitor presence) on the degree of grafting, amount of homopolymer produced and surface electrical resistance was determined. A degree of grafting up to 18 mmol/g was obtained, which resulted in sample resistance as low as 30 mΩ cm². The molecular weight of AAc homopolymer that can be assumed as equal to the MW of grafted chains, ranged from 25,000 to 50,000,000 da. SEM and water permeability measurements show that grafting causes filling of the pores, which, however, does not stop K⁺ ions from penetrating the membrane. The performance of nickel‐cadmium cells with acrylic acid grafted membranes as separator is also presented. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

THERMODYNAMIC PROPERTIES OF FRACTIONAL DIFFERINTEGRO TYPE CONSTITUTIVE RELATIONS

Abstract

Using the asymptotic properties of Riemann-Liouville form, the intrinsic rate-based first and second laws of thermodynamics properties of fractional differintegro operator type constitutive representations are investigated by illustrating how the conservative and nonconservalive features of the response behavior interact under spectrally rich inputs. Due to the generality of the development, fractional operator representations of any order are considered. This includes the determination of the underlying features giving rise to frequency dependencies in the phasing and amplitude behavior and in this context the irreversible energy release rate process associated with fractional viscoelastic simulations.     

Mercury in fruiting bodies of dark honey fungus (Armillaria solidipes) and beneath substratum soils collected from spatially distant areas

BACKGROUND: This paper reports data on bioconcentration potential and baseline mercury concentrations of fruiting bodies of dark honey fungus (Armillaria solidipes) Peck and soil substrate layer (0–10 cm) from 12 spatially distant sites across Poland. Mercury content of caps, stipes and soil samples were determined using validated analytical procedure including cold‐vapor atomic absorption spectroscopy after thermal decomposition of the sample matrix and further amalgamation and desorption of mercury from gold wool. RESULTS: Mean mercury concentrations ranged from 20 ± 8 to 300 ± 70 ng g^?1 dry weight (dw) in caps, from 20 ± 6 to 160 ± 40 ng g^?1 dw in stipes, and in underlying soil were from 20 ± 2 to 100 ± 130 ng g^?1 dw. The results showed that stipes mercury concentrations were 1.1‐ to 1.7‐fold lower than those of caps. All caps and the majority of stipes were characterized by bioconcentration factor values > 1, indicating that dark honey fungus can be characterized as a moderate mercury accumulator. CONCLUSION: Occasional or relatively frequent eating of meals including caps of dark honey fungus is considered safe in view of the low total mercury content, and the mercury intake rates are below the current reference dose and provisionally tolerable weekly intake limits for this hazardous metal. © 2012 Society of Chemical Industry