Quasi-optical measurement of complex dielectric constant at 300 GHz

A two beam interferometer in the Martin-Puplett configuration is used to determine the complex dielectric constant at 300 GHz of teflon, TPX-plastics, SPECTRALON and paraffin waxes with melting temperatures of 48° C and 72° C, respectively. The design of the quasi-optical system leads to a constant beam diameter at the power detector independent of path delay and frequency. The power detector signal is recorded not only along one period but over about 50 periods. A spectrum estimation routine allows to determine more exactly amplitude and phase angle of the signal. A basic problem is noticed: imperfect detector and source match cause harmonic distortion of the power detector signal. The effects on processing the loss tangent and the invalidation are shown. Finally loss tangent and dielectric constant are determined indirectly by optimizing an equivalent microwave circuit using a commercial available microwave design system to take multiple reflections and losses in consideration.     

A streamlined approximation and duality scheme for structural optimization

An efficient and commonly used approach to structural optimization is to solve a sequence of approximate design problems that are constructed iteratively. As is well-known, a major part of the computational burden of this scheme lies in the sensitivity analysis needed to state the approximate problems. We propose a possibility for reducing this burden by streamlining the calculations in a combined approximation and duality scheme for structural optimization. The difference between this scheme and the traditional one is that, instead of calculating all the constraint gradients to state an approximate design problem explicitly, linear combinations of these gradients are generated as they are needed during the solution of the approximate problem by the dual method. We show, by analysing some typical scenarios of problem characteristics, that this rearrangement of the calculations may be a computationally viable alternative to the traditional scheme. An advantage of streamlining the calculations is that there is no need to incorporate an active set strategy in the scheme, as is usually done, since all the design constraints may be taken into consideration without any loss of computational efficiency. This may, clearly, enhance the practical rate of convergence of the overall approximation scheme. Moreover, the proposed rearrangement of the calculations may make it computationally viable to apply iterative equation solvers to the structural analysis problem. Numerical results with direct as well as iterative equation solvers show that the streamlined scheme is a feasible and promising approach to structural optimization.     

Betriebsmittelbezogene Lastmodellierung in Verteilungsnetzen

Übersicht Der Betriebszustand eines Verteilungsnetzes wird durch die Strombelastung aller Betriebsmittel beschrieben. Mit Hilfe einer statischen Estimationsmethode werden aus einzelnen Messungen und der Kenntnis der Verbrauchsdaten typische Verbraucherkurven (TVK) berechnet, die das elektrische Verhalten verschiedener Verbrauchergruppen widerspiegeln. Auf dieser Basis ist eine betriebsmittelbezogene Lastmodellierung an beliebigen Betriebsmitteln in Abhängigkeit der Verbraucherzusammensetzung unter Berücksichtigung externer Einflüsse wie der Temperatur möglich. Die so gewonnenen Belastungsverläufe erlauben eine Beschreibung des Netzzustands in den Verteilungsnetzen.

---

Bus load modelling in distribution systems

Contents The operating state of a distribution system is determined by the bus load current. Based on individual substation measurements and the load composition typical load curves are calculated using statistical estimation theory. These typical load curves describe the electrical behaviour of the different load types (e.g. household, storage heating, commerce etc.). As soon as the typical load curves are determined it is possible to calculate the bus load current in any substation taking external influences such as temperature into consideration. The bus load current serve as load models which completely describe the operating state of the distribution system.

     

Finite element modelling of calendering — some aspects of the effects of temperature gradients and structure inhomogeneities

The compression of a paper web in a calender nip has been simulated using the finite element method. The mechanical properties of the paper were allowed to vary in the thickness and machine directions of the web. This was done in order to model the influence of temperature gradients as well as density variations (due to the presence of fibre floes) on the deformation behaviour in the nip. Paper was assumed to be an elastic-plastic material exhibiting strain hardening. The yielding behaviour was governed by the Drucker-Prager yield condition. Simulations of the deformation behaviour when paper was subjected to a temperature gradient, clearly revealed that the deformation gradually became more concentrated towards the surface layers as the temperature of the surface increased. This is in accordance with experimental results which indicate that temperature-gradient calendering promotes the surface properties, whereas the bulk of the structure is preserved. Modelling the deformation behaviour of a structure containing density variations reveals that the paper may contain an inhomogeneous strain distribution after unloading, i.e. after passage through the nip.     

Tocopherol contents of some Turkish wine by-products

The aim of this study was to determine the tocopherol contents of wine by-products including grape seed, pomace (seed, skin and stem) and bagasse (skin and stem) by using two different extraction methods in order to evaluate the possibilities of them as natural non-polar antioxidants. Cold extraction appeared to give more tocopherol contents in seeds than hot extraction. But hot extraction was found more suitable for pomace and bagasse. α-Tocopherol was the most abundant tocopherol in the grape seed, pomace and bagasse. Although γ- and δ-tocopherols were found in the samples with low concentrations, β-tocopherol was not detected in the samples. Kalecik karası had the highest α and total tocopherol compared to the other cultivars. On the other hand, hot extracted bagasse in all cultivars gave the highest tocopherol contents. As a conclusion, wine by-products, a large scale wastes, can be evaluated both to get natural tocopherol source and to obtain economical gain.     

Tensile,creep, and low-cycle fatigue behavior of a cast γ-TiAl-based alloy for gas turbine applications

The influence of chemical composition on the microstructure of the γ-titanium aluminide alloy Ti-48Al-2W-0.5Si (at. pct) and the accompanying tensile, low-cycle fatigue, and creep properties has been evaluated. The study showed that small variations in chemical composition and casting procedures resulted in considerable variations in the microstructure, yielding vastly different mechanical properties. Low contents of aluminum and tungsten led to a coarse-grained lamellar (γ/α ₂) microstructure with high creep resistance. A composition close to the nominal one produced a duplex (γ+γ/α ₂) structure with favorable strength, ductility, and low-cycle fatigue properties. By controlling the solidification and cooling rates at casting, a pseudoduplex (PS-DP) microstructure with a unique combination of high strength and high fatigue and creep resistance can be obtained. These unique properties can be explained by the diffuse boundaries between the relatively small γ grains and the neighboring lamellar colonies, combined with semicoherent interfaces between the γ and α ₂ phases. At tensile and low-cycle fatigue loading, these boundaries act like high-angle boundaries, producing a virtually fine-grained material promoting strength, whereas at creep loading, grain-boundary sliding is hindered in the semicoherent interfaces leading to high creep resistance.     

Crystallographic electron microscopy

We present a family of techniques for the transmission electron microscope that generate surface zone-axis patterns. These patterns display the variation of the diffracted-beam intensity as a function of the angle of the incident electrons. The conditions of the experiments are those of reflection high-energy electron diffraction at near grazing incidence. The techniques are: surface convergent-beam diffraction, a surface analogue of the Tanaka method and a modified double-rocking scheme. Experimental results are presented for diffraction from surfaces of MgO and MoS₂. We anticipate that surface zone-axis patterns (surface ZAPs) will become established as an important tool for surface characterization, especially when used in conjunction with high-resolution surface imaging and surface energy loss spectroscopy; surface ZAPs may be expected to play, in surface analysis, a role analogous to that played by convergent-beam diffraction in normal transmission electron microscopy.