Scaling planar silicon devices

The generation-over-generation scaling of critical CMOS technology parameters is ultimately bound by nonscalable limitations, such as the thermal voltage and the elementary electronic charge. Sustained improvement in performance and density has required the introduction of new device structures and materials. Partially depleted SOI, a most recent MOSFET innovation, has extended VLSI performance while introducing unique idiosyncrasies. Fully depleted SOI is one logical extension of this device design direction. Gate dielectric tunneling, device self-heating, and single-event upsets present developers of these next-generation devices with new challenges. Strained silicon and high-permittivity gate dielectric are examples of new materials that will enable CMOS developers to continue to deliver device performance enhancements in the sub-100 nm regime.     

Effects of SiN passivation and high-electric field on AlGaN-GaN HFET degradation

The authors report on the effects of silicon nitride (SiN) surface passivation and high-electric field stress (hot electron stress) on the degradation of undoped AlGaN-GaN power HFETs. Stressed devices demonstrated a decrease in the drain current and maximum transconductance and an increase in the parasitic drain series resistance, gate leakage, and subthreshold current. The unpassivated devices showed more significant degradation than SiN passivated devices. Gate lag phenomenon was observed from unpassivated devices and removed by SiN passivation. However, SiN passivated devices also showed gate lag phenomena after high-electric field stress, which suggests possible changes in surface trap profiles occurred during high-electric field stress test.     

High-performance MIM capacitor using ALD high-k HfO/sub 2/-Al/sub 2/O/sub 3/ laminate dielectrics

For the first time, we successfully fabricated and demonstrated high performance metal-insulator-metal (MIM) capacitors with HfO/sub 2/-Al/sub 2/O/sub 3/ laminate dielectric using atomic layer deposition (ALD) technique. Our data indicates that the laminate MIM capacitor can provide high capacitance density of 12.8 fF//spl mu/m/sup 2/ from 10 kHz up to 20 GHz, very low leakage current of 3.2 /spl times/ 10/sup -8/ A/cm/sup 2/ at 3.3 V, small linear voltage coefficient of capacitance of 240 ppm/V together with quadratic one of 1830 ppm/V/sup 2/, temperature coefficient of capacitance of 182 ppm//spl deg/C, and high breakdown field of /spl sim/6 MV/cm as well as promising reliability. As a result, the HfO/sub 2/-Al/sub 2/O/sub 3/ laminate is a very promising candidate for next generation MIM capacitor for radio frequency and mixed signal integrated circuit applications.     

Transmission performance of 10-Gb/s 1550-nm transmitters using semiconductor optical amplifiers as booster amplifiers

We have demonstrated the transmission performance of 10-Gb/s transmitters based on LiNbO/sub 3/ modulator using semiconductor optical amplifiers (SOAs) as booster amplifiers. Utilizing the negative chirp converted in SOAs and self-phase modulation induced by high optical power, we can successfully transmit 10-Gb/s optical signals over 80 km through the standard single-mode fiber with the transmitter using SOAs as booster amplifiers. SOAs can be used for booster amplifiers with a careful adjustment of the operating conditions. In order to further understand an SOA's characteristics as a booster amplifier, we model SOAs and other subsystems to verify the experimental results. Based on the good agreement between the experimental and simulation results, we can find the appropriate parameters of input signals for SOAs, such as extinction ratio, rising/falling time, and chirp parameter to maximize output dynamic range and available maximum output power (P/sub o,max/).     

Lost retransmission detection for TCP SACK

There have been a lot of works to avoid retransmission timeout (RTO) of transmission control protocol (TCP) that takes place in an unnecessary situation. However, most current TCP implementations, even if selective acknowledgment (SACK) option is used, do not have a mechanism to detect a lost retransmission and avoid subsequent RTO. In this letter, we propose a simple modification that enables a TCP sender using SACK option to detect a lost retransmission, which is called TCP SACK+ in simple. We use a stochastic model to evaluate the performance of TCP SACK+. Numerical results evaluated by simulations show that TCP SACK+ improves the loss recovery of TCP SACK significantly in presence of random losses.     

Geometric derivation of expectation-maximization and generalized successive interference cancellation algorithms with applications to CDMA channel estimation

The expectation-maximization (EM) algorithm is well established as a computationally efficient method for separable signal parameter estimation. Here, a new geometric derivation and interpretation of the EM algorithm is given that facilitates the understanding of EM convergence properties. Geometric considerations lead to an alternative separable signal parameter estimator based on successive cancellation. The new generalized successive interference cancellation (GSIC) algorithm is then applied to multiuser delay and channel estimation for code-division multiple access (CDMA) radiolocation and communication. The radiolocation application uses a handshaking protocol in which multiple reference nodes transmit acknowledge (ACK) CDMA packets to a master node, which then computes round-trip travel times (RTTs). Simulation results comparing EM and GSIC are presented for the CDMA channel-estimation problem.     

A study of the numerical dispersion relation for the 2-D ADI-FDTD method

This letter presents a numerical dispersion relation for the two-dimensional (2-D) finite-difference time-domain method based on the alternating-direction implicit time-marching scheme (2-D ADI-FDTD). The proposed analytical relation for 2-D ADI-FDTD is compared with those relations in the previous works. Through numerical tests, the dispersion equation of this work was shown as correct one for 2-D ADI-FDTD.     

Simultaneous amplification by Er ions and SRS in an Er-doped germano-silica fiber

A flat signal gain over in the entire C- and L-bands by erbium (Er) ions' radiative transition and stimulated Raman scattering in an Er-doped germano-silica fiber can be obtained if proper values of the concentration of Er and background loss in a fiber core are obtained during the fiber fabrication process. The optimized conditions for the flat C- and L-band gain are analyzed as functions of Er concentrations. Even for a low-gain value provided by a germano-silica core fiber with a low Er concentration and an optimum fiber length, a relatively low pump is required to obtain the flat gain band.     

Sociotechnical systems, risk management, and public health: comparing the North Battleford and Walkerton outbreaks

Accidents in different complex sociotechnical systems are rarely compared using the same theoretical framework for risk management. We conducted a comparative analysis of two Canadian public health disasters involving drinking water distribution systems, the North Battleford Cryptosporidium parvum outbreak in April 2001 and the Walkerton E. coli outbreak in May 2000. Both accidents resulted from a complex interaction between all levels of a complex sociotechnical system. However, the low-level physical and individual factors differed in the two cases, whereas, the high-level governmental and regulatory factors tended to be the same. These findings may have implications for the design of public policies to minimize risk in complex sociotechnical systems.     

Measurement and numerical simulation of three‐dimensional fiber orientation states in injection‐molded short‐fiber‐reinforced plastics

To determine three‐dimensional fiber orientation states in injection‐molded short‐fiber composites, a confocal laser scanning microscope (CLSM) is used. Since the CLSM optically sections the specimen, more than two images of the cross sections on and below the surface of the composite can be obtained. Three‐dimensional fiber orientation states can be determined by using geometric parameters of fiber images obtained from two parallel cross sections. For experiments, carbon‐fiber‐reinforced polystyrene is examined by the CLSM and geometric parameters of fibers on each cross‐sectional plane are measured by an image analysis. In order to describe fiber orientation states compactly, orientation tensors are determined at different positions of the prepared specimen. Three‐dimensional orientation states are obtained without any difficulty by determining the out‐of‐plane angles utilizing fiber images on two parallel planes acquired by the CLSM. Orientation states are different at different positions and show the shell–core structure along the thickness of the specimen. Fiber orientation tensors are predicted by a numerical analysis and the numerically predicted orientation states show good agreement with measured ones. However, some differences are found at the end of cavity. They may result from the fountain flow effects, which are not considered in the numerical analysis. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 500–509, 2003