Optimal diagonal precoder for multiantenna communication systems

In this paper, we examine a multiantenna single-user wireless communication system fitted with a QR-based successive cancellation receiver (QR receiver). Initially, our consideration is confined to uncoded binary phase shift keying (BPSK) signals transmitted through independent and identically distributed (IID) Rayleigh fading channels and to the design of an optimum precoder for the transmitter. For minimum feeding back of the channel state information (CSI) to the transmitter from the receiver, we stipulate the precoder to be in the form of a power loading square diagonal matrix. We proceed to develop the theory for the design of this diagonal matrix based on the minimization of the lower bound of the average bit error rate (BER) of transmission. The design obtained provides substantially lower error rates than most of other existing schemes under the same environment. The corresponding gain in signal-to-noise ratio (SNR) can be several decibels. To further improve the performance, we extend the design to include an optimal detection order of the received bits using an iterative approach. This iterative process proves to have fast convergence and results in a design providing significant SNR gain. We also propose a subchannel dropping scheme for cases in which SNR is low, and when the minimum BER precoder is equipped with this scheme, its average performance can be substantially superior to the Vertical Bell Laboratories Layered Space-Time (V-BLAST) detection. We extend our design of the optimum precoder to quadrature amplitude modulation (QAM) modulation scheme and similar performance gain has been observed.     

Studies on the microstructure of the black-glazed bowl sherds excavated from the Jian kiln site of ancient China

The Jian kiln, located in present-day Jianyang county of Fujian province, mainly produced black-glazed tea bowls. Jian tea bowl was used as a utensil for tea tasting and was greatly appreciated by emperor Huizong of the Northern Song dynasty. The black glaze of Jian bowl was sometimes marked with streaks or spots, usually called “hare's fur” or “oil spot”, which are the crystalline markings of iron oxide precipitated during firing in the dragon kiln. In this study, black-glazed Jian bowl sherds excavated from the late Northern Song strata of Luhuaping and Daluhoumen Jian kiln sites were adopted as test samples. Based on the physico-chemical foundation for the formation of glaze microstructure, the correlation among composition, microstructure, and visual appearance has been investigated by means of energy-dispersive X-ray fluorescence, X-ray diffraction, and field emission electron microscopy. For the first time, the study provides realizing proofs for two kinds of microstructural forming mechanics.     

Microstructure and fatigue properties of hydroformed aluminum alloys 6063 and 5754

This study investigated the microstructure and fatigue properties of hydroformed sections of the 5754 and 6063 aluminum alloys. The second-phase particles in 6063-T7 are identified as a mixture of Al₁₂Fe₃Si and Al₉Fe₂Si₂, with a slightly higher fraction of the former. The constituent particles in the 5754 alloy are Al₄Mn-type hexagonal compounds, where Mn is partially substituted by various other elements, resulting in Al₄(Fe,Mn,Si,Cr). The results show that despite its lower yield strength, the hydroformed 5754 alloy has higher ultimate tensile strength, ductility, and, more importantly, higher fatigue resistance than the 6063 material. Both crystallographic stage I and noncrystallographic stage II cracking are found in the 6063-T7 samples, but only stage II cracking is observed in the 5754 alloy. This implies that the low fatigue strength of 6063-T7 is related to its relatively large grain size, resulting in rapid stage I crack propagation. The higher fatigue lives of the 5754 alloy compared to the 6063 alloy in both the low- and high-cycle life regimes are due to the increased fatigue-crack-initiation and propagation resistance of the 5754 alloy and its probable cyclic strain-hardening behavior.     

IRIS/AP型电感耦合等离子体光谱仪激发光源常见故障分析

本文介绍IRIS/AP型ICP的激发光源(炬管),并较为全面地阐述和分析其不能正常激发点燃的常见故障及其原因。     

大孔径石蜡加氢精制催化剂的制备

采用氨吸附-程序升温脱附(NH3-TPD)、低温N2吸附(BET)、压汞法以及加氢精制活性评价等技术,探索SiO2-Al2O3载体在制备过程中孔结构和表面性质的变化。实验结果表明,采用特殊扩孔剂制备载体,当焙烧温度为700℃时,平均孔径可达到17.3nm,其中孔径大于20nm的孔占总孔体积的13.2%;同时载体表面上的中、强酸中心也全部丧失,均为弱酸中心。采用该载体制备的MoNiP/SiO2-Al2O3石蜡加氢精制催化剂,在MoO3用量减少了约1/4的情况下,比目前工业上使用的催化剂具有更高的脱金属能力和加氢精制活性。     

TD-SCDMA系统基站间干扰分析

论文以TD-SCDMA通信系统为基础详细分析了TDD系统特有的干扰即基站间干扰问题,同时介绍了基站间干扰分析的具体理论、分析方法和仿真结果,对于TDD系统的实际网络规划和设计具有指导意义。     

创新设计与管理(三):问题求解技术与头脑风暴法

1问题求解PS技术 无论进行何种问题的分析、研究和解决都离不开问题求解（PS，problem solving）的技术与方法。创新设计与管理的本质也是最新的现代问题求解技术与方法。本讲主要介绍问题求解的一般知识。最先进的问题求解技术就是以TRIZ和ADT创新设计与管理理论为代表的新一代问题求解技术，它们正是本讲座以后要介绍的。     

One-to-Many and Many-to-One Optical Chaos Communications Using Semiconductor Lasers

A theoretical construction of one-to-many (OTM) and many-to-one (MTO) chaos synchronization communications using semiconductor lasers is presented. One center laser provides strong injections (strong link) to other side lasers, and the side lasers also provide weak injections (weak link) to the center one. Simulation results show that the side lasers synchronize with the center laser through injection-locking. In addition, messages transmitted via the strong links or the weak links experience strong chaos pass filtering, enabling us to realize OTM and MTO communications.     

Estimation for the number of components in a mixture model using stepwise split-and-merge EM algorithm

The main difficulty with EM algorithm for mixture model concerns the number of components, say g. This is the question of model selection, and the EM algorithm itself could not estimate g. On the contrary, the algorithm requires g to be specified before the remaining parameters can be estimated. To solve this problem, a new algorithm, which is called stepwise split-and-merge EM (SSMEM) algorithm, is proposed. The SSMEM algorithm alternately splits and merges components, estimating g and other parameters of components simultaneously. Also, two novel criteria are introduced to efficiently select the components for split or merge. Experimental results on simulated and real data demonstrate the effectivity of the proposed algorithm.