Multibody simulation tool for the calculation of lashing loads on RoRo ships

Approximately 80% of the international transport of goods is carried on by means of ships. A large portion of the transport capacity is represented by Roll-on-Roll-off (RoRo) ships. Especially in Europe this is a relevant potential for the RoRo segment. Consequently, the design and construction of RoRo ships plays an increasing role for German shipyards and their suppliers. In order to make the loading and unloading procedure of trailer economically more competitive, ship owners would like to improve the lashing of trailers on the ship. On the basis of a multibody system formalism, a software tool has been developed which allows for an optimization of the loading of trailers on RoRo ships. Commemorative Contribution.     

Formulation for Reliable Analysis of Structural Frames

Structural engineers use design codes formulated to consider uncertainty for both reinforced concrete and structural steel design. For a simple one-bay structural steel frame, we survey typical uncertainties and compute an interval solution for displacements and forces. The naive solutions have large over-estimations, so we explore the Mullen-Muhanna assembly strategy, scaling, and constraint propagation to achieve tight enclosures of the true ranges for displacements and forces in a fraction of the CPU time typically used for simulations. That we compute tight enclosures, even for large parameter uncertainties used in practice, suggests the promise of interval methods for much larger structures.     

SCC casting prediction for the realization of prototype VHPC-precambered composite beams

Casting simulations of self-compacting concrete are carried out in order to obtain a value of the minimum fluidity needed to cast a VHPC precambered composite beam. The mix proportioning of the concrete takes into account this minimum value. The numerical predictions are finally compared with the experimental observations during two casting tests and the real casting of the two 13 m beams. Although the simplifying assumptions needed to carry out the simulations are numerous, there is an agreement between the predictions and the real casting.     

Critical Configurations for 1-View in Projections from ℙ<Superscript>k</Superscript> → ℙ<Superscript>2</Superscript>

In this paper we describe, from a theoretical point of view, critical configurations for the projective reconstruction of a set of points, for a single view, i.e. for calibration of a camera, in the case of projections from ℙ^k to ℙ² for k ≥ 4. We give first a general result describing these critical loci in ℙ^k, which, if irreducible, are algebraic varieties of dimension k−2 and degree 3. If k=4 they can be either a smooth ruled surface or a cone and if k = 5 they can be a smooth three dimensional variety, ruled in planes, or a cone. If k≥ 6, the variety is always a cone, the vertex of which has dimension at least k − 6. The reducible cases are studied in Appendix A. These results are then applied to determine explicitly the critical loci for the projections from ℙ^k which arise from the dynamic scenes in ℙ³ considered in [13]. Marina Bertolini is currently Associate Professor of Geometry at the Department of Mathematics at the Università degli Studi di Milano, Italy. Her main field of research is Complex Projective Algebraic Geometry, with particular interest for the classification of projective varieties and for the geometry of Grassmann varieties. On these topics M. Bertolini has published more than twenty reviewed papers on national and international journals. She has been for some years now interested also in applications of Algebraic Geometry to Computer Vision problems. Cristina Turrini is Associate Professor of Geometry at the Department of Mathematics of Università degli Studi di Milano, Italy. Her main research interest is Complex Projective Algebraic Geometry: subvarieties of Grassmannians, special varieties, automorphisms, classification. In the last two years she has started to work on applications of Algebraic Geometry to problems of Computer Vision. She is author or co-author of about thirty reviewed papers. She is also involved in popularization of Mathematics, and on this subject she is co-editor of some books.     

Phase equilibria of the ternary Al-Cu-Ni system and interfacial reactions of related systems at 800 °C

A series of Al-Cu-Ni alloys of various compositions were made and annealed at 800 °C. The equilibrium phases were studied by metallography, X-ray diffraction (XRD) analysis, and electron probe microanalysis. The isothermal section of the ternary Al-Cu-Ni system at 800 °C was then determined based on these experimental results and the available phase relationship knowledge of the three constituent binary systems. No ternary compound was found. All three phases, AlNi₃, AlNi, and Al₃Ni₂, have very high ternary solubility, especially the AlNi phase, which almost reaches the binary Al-Cu side. However, no continuous solid solution was formed between the AlNi phase and any of the binary Al-Cu phases. Interfacial reactions of Al/Ni, Al/Cu, Al-Cu/Ni, and Al-Ni/Cu at 800 °C were investigated by using reaction couple techniques. The results showed that Al₃Ni and Al₃Ni₂ phases were formed in the Al/Ni couples; β-AlCu₄, γ ₁-Al₄Cu₉, and ɛ ₂-Al₂Cu₃ phases were formed in the Al/Cu couples. As for the results in the Al-2 at. pct Ni/Cu, Al-5 at. pct Ni/Cu, and Al-2 at. pct Cu/Ni, Al-4.5 at. pct Cu/Ni, and Al-6 at. pct Cu/Ni were similar to those in the binary Al/Cu and Al/Ni couples, respectively. A different reaction path was found in the Al-7.5 at. pct Cu/Ni couples, and an AlNi solid solution layer was formed instead of the Al₃Ni and Al₃Ni₂ phases.     

The hot blow forming of AZ31 Mg sheet: Formability assessment and application development

The hot blow forming of magnesium sheet offers significant opportunity for forming complex, lightweight parts for automotive applications. This paper characterizes the elevated-temperature formability of AZ31 magnesium sheet materials and the effect of processing conditions on the performance of these materials. In addition, magnesium sheet application development at General Motors Corporation is reviewed.     

Anfangsvorgänge bei Lichtenbergschen Figuren

Zusammenfassung Aufnahmen von Lichtenbergschen Figuren mit kurzen Spannungsstößen zeigen, daß bisher bekanntgewordene Bilder solcher Entladungsfiguren bereits ein verhältnismäßig weit vorgeschrittenes Stadium darstellen. Es gelingt mittels kurzer Stöße erste lawinenartige Anfänge der Figuren festzuhalten und einiges über Vorgänge im Anfangsstadium herauszulesen. Die negative Figur beginnt lawinenförmig an bevorzugten Stellen der Kathode. Bei nebeneinander entstandenen Lawinen ist sehr gut die gegenseitige Abstoßung infolge gleicher Ladung zu beobachten. Die Entladung hat einen geschichteten Aufbau. Die positiven Figuren bilden sich später aus. Es sprechen jedoch bisher keinerlei Anzeichen für ein Hinwachsen der Fäden zur Anode. Die Kanäle verjüngen sich zur Anode hin und selbst bei kurzen Stoßzeiten endet kein einziger vor der Anode. Auch die Art der gegenseitigen Abstoßung der positiven Fäden spricht mehr für ein Vorwachsen von der Anode aus. Aus den Farbaufnahmen ergibt sich für die filmschwärzende Strahlung eine Wellenlänge unter 450 m.     

Simulation of Strength Distribution in Ground Ceramics by Incorporating Residual Stress Effect

Strength of ground ceramics may be affected by residual stress as well as surface flaws induced by grinding. Strength prediction for ground ceramics is convenient for mechanical design of ceramic components. In this article, a numerical procedure based on fracture mechanics was proposed to estimate strength distribution of ground ceramics by considering grinding-induced residual stress. Bending strength and residual stress of ground ceramics were measured for three grinding-conditions. By comparison of simulated results with experimental ones, it was revealed that strength characteristics in experiments were well simulated by using the proposed procedure.     

Adaptive user modelling in intelligent telephone and email assistants

With the burgeoning complexity and capabilities of modern information appliances and services, user modelling is becoming an increasingly important research area. Simple user profiles already personalise many software products and consumer goods such as digital TV recorders and mobile phones. A user model should be easy to initialise, and it must adapt in the light of interaction with the user. In many cases, a large amount of training data is needed to generate a user model, and adaptation is equivalent to retraining the system. This paper briefly outlines the user modelling problem and work done at BTexact on an intelligent personal assistant (IPA) which incorporates a user profile. We go on to describe FILUM, a more flexible method of user modelling, and show its application to the telephone assistant and email assistant components of the IPA, with tests to illustrate its usefulness.