Nano Zinc Oxide-Loaded Calcium Alginate Films with Potential Antibacterial Properties

In this work, zinc oxide nanoparticles-loaded calcium alginate films were investigated for their moisture uptake behavior at different temperatures. The equilibrium uptake data was interpreted quantitatively by GAB isotherm models. The monolayer moisture contents were 0.301 ± 0.003, 0.0214 ± 0.092, and 0.171 ± 0.102 at 20, 30, and 37°C, respectively. The water vapor transmission rate was found to be 0.816 ± 0.143, 1.42 ± 0.045, and 1.632 ± 0.064 g s⁻¹ m⁻² respectively. For the moisture content range of 0.2 to 0.6, the net ∆H and ∆S values were found to be 22.73 to 11.14 KJ/mol and 0.064 to 0.034 KJ/mol/K, respectively. The moisture uptake of films increased with water activity but showed negative temperature dependence. The enthalpy of sorption (∆H) and differential entropy (∆S) were determined at different moisture content values, ranging from 0.2 to 0.6 g/g db. The two parameters showed a higher degree of correlation. The equilibrium moisture content data was used to evaluate harmonic mean temperature T _hm. Finally, the biocidal action of films was tested against model bacteria Escherichia coli.     

Influence of Fibre Orientation on Friction and Sliding Wear Behaviour of Jute Fibre Reinforced Polyester Composite

Jute fibre reinforced polyester composites were developed and characterized for friction and sliding wear properties. Effect of fibre orientation and applied load on tribological behaviour of jute fibre reinforced polyester composites were determined. It is found that wear resistance was maximum in TT sample, where fibres were normal to sliding direction. Wear rate under sliding mode follows this trend; W_TT < W_LT <W_LL LL sample showed higher capability to sustain the load whereas lowest wear resistance found in this case. The coefficient of friction found highest for TT sample and lowest for LT sample. The coefficient of friction decreased with increase of applied load. Worn surfaces were analysed and discussed with the help of SEM.     

Dynamic viscoelasticity of hybrid kevlar and glass fiber reinforced LLDPE in the molten state

Kevlar and glass fibers were used to reinforce linear low density polyethylene (LLDPE), and composite sheets of 0.8, 1.5 and 2.5 mm thicknesses were obtained by using a compression molding technique. Dynamic viscoelastic properties of non‐hybrid and hybrid composites of various compositions at 200°C are evaluated. Storage modulus (G′) and loss modulus (G″) increase with angular frequency (ω) and reinforcement. Replacement of glass fiber by Kevlar at constant loading of fibers in LLDPE increases the value of G′, G″ and η′. The fractured surface of composite shows the gradient orientation of fibers particularly in 2.5 mm thick sheet. Top and bottom layers show relatively two‐dimensional orientation as compared to the middle layer, which shows random orientation. The orientation of fibers decreases G′ and η′ of Kevlar fiber and hybrid fiber hybrid fiber reinforced LLDPE composites. The effect of change in distance between parallel plate of rheometer (change in strain amplitude) on dynamic rheological properties is studied and reported here.     

Dynamic mechanical behavior of LCP fiber/glass fiber–reinforced LLDPE composites

Liquid crystalline polymer (LCP) fibers and glass fibers have been used to rein force linear low density polyethylene (LLDPE) by using an elastic melt extruder and the compression molding technique. The impact behavior of hybrid composites of different composition is compared and is explained on the basis of the volume frac tion of the fibers. Addition of glass fibers decreases the Izod impact strength LLDPE. The impact strength of the composites increases when glass fibers are placed by LCP fibers. Dynamic mechanical α and β relaxations are studied and effect of variation of fiber composition on these relaxations is reported in the tem perature range from −50 to 150°C at 1 Hz frequency, a relaxation shifts toward higher temperatures with addition of fibers in LLDPE. Addition of fibers increases the storage modulus of LLDPE.     

Studies on Influence of Polymers and Excipients on Crystallization Behavior of Metformin HCl to Improve the Manufacturability

The aim of this work was to improve the mechanical properties of Metformin HCl by its recrystallization in the presence of different polymers and excipients using a wide range of polarity solvents. The recrystallized drug in the presence of lactose anhydrous (lactose) was further studied for its topographical, micromeritic, mechanical, compressional, solubility, and dissolution properties. Lactose-treated crystals were bigger in size with equidimentional shape. Crystals showed improvement in flow and packability with rich drug content (96.17%). Heckel parameters indicated greater plastic deformation (K = 0.474) and tensile strength compared to the pure drug (K = 0.137). Pellets prepared from crystals showed negligible elastic recovery (1.06%) compared to the pure drug (5.73%). Differential scanning calorimetry showed no degradation or polymorphic transformation of the drug even after stability studies (40°C, 75% RH). Fourier transform infrared spectroscopy proved hydrogen bond generation between the drug and lactose with a stable nature. The amount of directly compressible diluents could be minimized in tablet formulation, which ultimately reduced the overall tablet mass. The study highlights an influence of lactose on morphology, leading to a modified performance of recrystallized Metformin HCl.     

Parallel Reaction Monitoring: A Targeted Experiment Performed Using High Resolution and High Mass Accuracy Mass Spectrometry

The parallel reaction monitoring (PRM) assay has emerged as an alternative method of targeted quantification. The PRM assay is performed in a high resolution and high mass accuracy mode on a mass spectrometer. This review presents the features that make PRM a highly specific and selective method for targeted quantification using quadrupole-Orbitrap hybrid instruments. In addition, this review discusses the label-based and label-free methods of quantification that can be performed with the targeted approach.     

Modeling of single and multilayer polyvinylidene fluoride film for micro pump actuation

Micro pumps are essential components of micro devices such as drug delivery systems. Large numbers of pumps have been proposed based on different actuating principles. Piezoelectric actuation offers advantages such as reliability and energy efficiency. Lead zirconate titanate (PZT) based piezoelectric actuation for micro pumps is predominantly explored despite its disadvantages such as brittle nature, low straining and difficulties in processing. Polymer piezoelectric materials like polyvinylidene fluoride (PVDF) could be promising replacements for PZT owing to their availability in form of films and good strain coefficients. Very limited literature on micro pump with PVDF as an actuator is available. In this paper, finite element analysis (FEA) model of a micro pump actuator using single and multilayer PVDF for actuation is developed in ANSYS^?. The model takes into account the influence of driving voltage and actuator geometry. The central deflection of the pump diaphragm which is instrumental in defining the pump performance is studied for driving voltages of 100?C200?V. The deflection of the pump diaphragm for single layer and multilayer actuation are determined from the model. It could be inferred from the initial part of the study that pump performance depends on driving voltage and actuator film thickness. In order to reduce driving voltage requirement multilayer stacked actuator is tried with four different configurations of the layers. It is concluded that stacking configuration of parallel energized straight polarity PVDF layers yielded best central deflection. An attempt is made to compare the performance of multilayer actuator with an equivalent single thick layer actuator. It is noticed that the multilayer actuator performance was better by about 101% when number of layers is doubled.