Life cycle GHG emissions from Malaysian oil palm bioenergy development: The impact on transportation sector's energy security

Malaysia's transportation sector accounts for 41% of the country's total energy use. The country is expected to become a net oil importer by the year 2011. To encourage renewable energy development and relieve the country's emerging oil dependence, in 2006 the government mandated blending 5% palm-oil biodiesel in petroleum diesel. Malaysia produced 16 million tonnes of palm oil in 2007, mainly for food use. This paper addresses maximizing bioenergy use from oil-palm to support Malaysia's energy initiative while minimizing greenhouse-gas emissions from land-use change. When converting primary and secondary forests to oil-palm plantations between 270–530 and 120–190 g CO₂-equivalent per MJ of biodiesel produced, respectively, is released. However, converting degraded lands results in the capture of between 23 and 85 g CO₂-equivalent per MJ of biodiesel produced. Using various combinations of land types, Malaysia could meet the 5% biodiesel target with a net GHG savings of about 1.03 million tonnes (4.9% of the transportation sector's diesel emissions) when accounting for the emissions savings from the diesel fuel displaced. These findings are used to recommend policies for mitigating GHG emissions impacts from the growth of palm oil use in the transportation sector.     

Enhancement of mechanical and thermal properties of polycaprolactone/chitosan blend by calcium carbonate nanoparticles

This study investigates the effects of calcium carbonate (CaCO(3)) nanoparticles on the mechanical and thermal properties and surface morphology of polycaprolactone (PCL)/chitosan nanocomposites. The nanocomposites of PCL/chitosan/CaCO(3) were prepared using a melt blending technique. Transmission electron microscopy (TEM) results indicate the average size of nanoparticles to be approximately 62 nm. Tensile measurement results show an increase in the tensile modulus with CaCO(3) nanoparticle loading. Tensile strength and elongation at break show gradual improvement with the addition of up to 1 wt% of nano-sized CaCO(3). Decreasing performance of these properties is observed for loading of more than 1 wt% of nano-sized CaCO(3). The thermal stability was best enhanced at 1 wt% of CaCO(3) nanoparticle loading. The fractured surface morphology of the PCL/chitosan blend becomes more stretched and homogeneous in PCL/chitosan/CaCO(3) nanocomposite. TEM micrograph displays good dispersion of CaCO(3) at lower nanoparticle loading within the matrix.     

Degradability Enhancement of Poly(Lactic Acid) by Stearate-Zn(3)Al LDH Nanolayers

Recent environmental problems and societal concerns associated with the disposal of petroleum based plastics throughout the world have triggered renewed efforts to develop new biodegradable products compatible with our environment. This article describes the preparation, characterization and biodegradation study of poly(lactic acid)/layered double hydroxide (PLA/LDH) nanocomposites from PLA and stearate-Zn₃Al LDH. A solution casting method was used to prepare PLA/stearate-Zn₃Al LDH nanocomposites. The anionic clay Zn₃Al LDH was firstly prepared by co-precipitation method from a nitrate salt solution at pH 7.0 and then modified by stearate anions through an ion exchange reaction. This modification increased the basal spacing of the synthetic clay from 8.83 Å to 40.10 Å. The morphology and properties of the prepared PLA/stearate-Zn₃Al LDH nanocomposites were studied by X-ray diffraction (XRD), transmission electron microscope (TEM), scanning electron microscope (SEM), thermogravimetric analysis (TGA), tensile tests as well as biodegradation studies. From the XRD analysis and TEM observation, the stearate-Zn₃Al LDH lost its ordered stacking-structure and was greatly exfoliated in the PLA matrix. Tensile test results of PLA/stearate-Zn₃Al LDH nanocomposites showed that the presence of around 1.0–3.0 wt % of the stearate-Zn₃Al LDH in the PLA drastically improved its elongation at break. The biodegradation studies demonstrated a significant biodegradation rate improvement of PLA in the presence of stearate-Zn₃Al LDH nanolayers. This effect can be caused by the catalytic role of the stearate groups in the biodegradation mechanism leading to much faster disintegration of nanocomposites than pure PLA.     

Effect of MnO2 additive on the dielectric and electromagnetic interference shielding properties of sintered cement-based ceramics

Cement-based ceramic pellets were prepared and their properties were studied for electromagnetic interference (EMI) shielding applications. The shielding materials were made of Portland cement with the addition of different concentrations of manganese oxide (MnO₂) up to 10 wt%. The pellets were sintered at 850 °C for 5 h and then polished prior to characterizations of density, porosity, microstructures, dielectric properties, and EMI shielding effectiveness (SE). Results show that the MnO₂-cement pellets have good dielectric properties, i.e. high dielectric constant (∼300) and low dielectric loss (<0.3). The dielectric constant increased with increasing MnO₂ content in the cement matrix. The SE values of the MnO₂-cements fluctuated between 2 dB and 9 dB in the frequency range of 8-13 GHz. The sample with 10 wt% MnO₂ additive had SE values of up to 9 dB. Most of the samples with high additive concentrations produced SE exceeding 7 dB.     

Melt Production and Antimicrobial Efficiency of Low-Density Polyethylene (LDPE)-Silver Nanocomposite Film

Colloidal silver nanoparticles with a size of 5.5 ± 1.1 nm were prepared by chemical reduction using polyethylene glycol (PEG). Silver nanoparticles were incorporated into low-density polyethylene (LDPE) by melt blending and subsequent hot pressing at 140 °C to produce nanocomposite film with an average thickness of 0.7 mm. PEG was added at 5% weight of polymer as a compatibilizer agent in order to prevent agglomeration and provide uniform distribution of nanoparticles in polymer matrix. Antimicrobial activity of silver nanocomposites against Escherichia coli ATCC 13706, Staphylococcus aureus ATCC12600, and Candida albicans ATCC10231 was evaluated by semi-qualitative agar diffusion test and quantitative dynamic shake flask test. Mechanical properties of nanocomposites were not significantly different from silver-free LDPE-containing PEG films (p > 0.05), and silver nanoparticles did not form chemical bonding with the polymer. LDPE-silver nanocomposite samples by more than 6.69 ppm silver nanoparticles showed considerable antimicrobial clear zone. LDPE-silver nanocomposite affected growth kinetic parameters of the examined bacteria and is more efficient on S. aureus than E. coli. Polyethylene-silver nanocomposites containing 22.64 ppm silver nanoparticles could reduce 57.8% growth rate and 23.3% maximum bacterial concentration and increase 35.8% lag time of S. aureus. This study shows the potential use of LDPE-silver nanocomposite as antimicrobial active film. Antimicrobial efficiency of silver nanocomposite depends on silver nanoparticles concentration; however, high level of silver nanoparticles may lead to weakening of mechanical properties.     

Superposition Coding with Unequal Error Protection for the Uplink of Overloaded DS-CDMA System

The overloaded CDMA schemes exploited in direct sequence CDMA (DS-CDMA) systems are mainly to accommodate a greater number of users than the available spreading factor N. In this paper, a superposition coding CDMA (SPC-CDMA) with unequal error protection (UEP) is proposed as one of the overloaded CDMA schemes for the next generation mobile communication systems. It exploits the available power control in most base stations to adapt the transmitted power of active users in the uplink channel. In this scheme, the active users are divided into G groups and each group consists of K users. The K users share the same spreading sequence and are distinguished by different received power levels. At the receiver side, the system first performs despreading for group detection followed by multiuser receiver to estimate the K user signals in each group. It is shown through simulations that better performance are achieved compared to the conventional DS-CDMA and existing overloaded collaborative spreading CDMA (CS-CDMA) schemes, in additive white Gaussian noise (AWGN) and fading channels. Hence, the proposed scheme maximizes the system capacity K-fold compared to conventional DS-CDMA system without requiring extra spreading codes, with average signal to noise ratio (SNR) cost of only 1dB and 2 dB over AWGN and fading channels respectively at BER of 10^?3. On the other hand, for the same N, K and power constraints, SPC-CDMA scheme achieves twofold increase in data rate with 0.7 and 4 dB gains over AWGN and fading channels respectively, compared with overloaded CS-CDMA scheme in the same system capacity. In addition, the proposed scheme can also attain different levels of UEP for different users?? requirements by adjusting their fractions of transmitted powers.     

An Enhanced A-MSDU Frame Aggregation Scheme for 802.11n Wireless Networks

The main goal of the IEEE 802.11n standard is to achieve a minimum throughput of 100 Mbps at the MAC service access point. This high throughput has been achieved via many enhancements in both the physical and MAC layers. A key enhancement at the MAC layer is frame aggregation in which the timing and headers overheads of the legacy MAC are reduced by aggregating multiple frames into a single large frame before being transmitted. Two aggregation schemes have been defined by the 802.11n standard, aggregate MAC service data unit (A-MSDU) and aggregate MAC protocol data unit (A-MPDU). As a consequence of the aggregation, new aggregation headers are introduced and become parts of the transmitted frame. Even though these headers are small compared to the legacy headers they still have a negative impact on the network performance, especially when aggregating frames of small payload. Moreover, the A-MSDU is highly influenced by the channel condition due mainly to lack of subframes sequence control and retransmission. In this paper, we have proposed an aggregation scheme (mA-MSDU) that reduces the aggregation headers and implements a retransmission control over the individual subframes at the MSDU level. The analysis and simulations results show the significance of the proposed scheme, specifically for applications that have a small frame size such as VoIP.     

Evaluation of shortenings based on various palm oil products

Several formulations based on blends of hydrogenated palm oil (MP 41·5°C) and palm stearin (IV 44) with other liquid oils, on direct blends of palm stearin with other liquid oils, and on 100% inter-esterified palm olein, were used as feedstocks in shortening production. The shortenings were stored at 20°C over a period of one month. Physicochemical characteristics, creaming properties and baking performance of the shortenings were evaluated and compared with the best shortening on the market. Slip melting point of the shortenings ranged from 41·5 to 46·4°C. Palm-cottonseed oil shortenings had higher solid fat contents at all temperatures than palm-soya bean or palm-low erucic acid rapeseed oil shortenings. The shortenings were rich in C₅₀, C₅₂and C₅₄ glycerides. Creaming power after 12 min of beating ranged from 1·55 to 1·77 cm³ g^?1. Palm stearin-cottonseed (3:2) oil shortening showed the best creaming performance. The specific volume of cakes ranged, for the experimental shortening, from 90% to 101% from the control, with low erucic acid-palm blends showing the best performance. In applications for both aerated cream and cakes, inter-esterified palm olein was excellent.     

MHD flow of a micropolar fluid towards a vertical permeable plate with prescribed surface heat flux

The problem of a steady mixed convection stagnation point flow towards a permeable vertical plate with prescribed surface heat flux immersed in an incompressible micropolar fluid is studied numerically. The governing partial differential equations are first transformed into a system of ordinary differential equations using a similarity transformation, before being solved numerically by a finite-difference scheme known as the Keller-box method and the Runge–Kutta–Fehlberg method with shooting technique. The effects of the material parameter, buoyancy parameter, suction/injection parameter and the Prandtl number on the fluid flow and heat transfer characteristics are discussed. It is found that dual solutions exist for both assisting and opposing flows. The skin friction coefficient and the local Nusselt number increase in the presence of suction and magnetic field. Moreover, suction as well as fluids with larger Prandtl number widens the range of the buoyancy parameter for which the solution exists.