Heat transfer enhancement in a tube using circular cross sectional rings separated from wall

A numerical study was undertaken for investigating the heat transfer enhancement in a tube with the circular cross sectional rings. The rings were inserted near the tube wall. Five different spacings between the rings were considered as p = d/2, p = d, p = 3d/2, p = 2d and p = 3d. Uniform heat flux was applied to the external surface of the tube and air was selected as working fluid. Numerical calculations were performed with FLUENT 6.1.22 code, in the range of Reynolds number 4475–43725. The results obtained from a smooth tube were compared with those from the studies in literature in order to validate the numerical method. Consequently, the variation of Nusselt number, friction factor and overall enhancement ratios for the tube with rings were presented and the best overall enhancement of 18% was achieved for Re = 15,600 for which the spacing between the rings is 3d.     

Determination of molecular, atomic, electronic cross-sections and effective atomic number of some boron compounds and TSW

The transmission of gamma-rays of some boron compounds (H₃BO₃, Na₂B₄O₇) and the trommel sieve waste (TSW) have been measured by using an extremely narrow-collimated-beam transmission method in the energy range 15.74-40.93 keV. Molecular, atomic and electronic cross-sections and effective atomic numbers have been determinated on the basis of mixture rule and compared with the results obtained from theory.     

Experimental and numerical investigation of heat and mass transfer during drying of Hayward kiwi fruits (Actinidia Deliciosa Planch)

In this paper we undertake an experimental and numerical study on heat and mass transfer analysis during drying of kiwi fruits. In the experimental part, the effects of various drying conditions in terms of air velocity, temperature and relative humidity on drying characteristics of kiwi fruits are investigated. In the numerical part, the external flow and temperature fields are studied using a commercial CFD package. From these fields, the local distributions of the surface convective heat transfer coefficients for the fruits are determined to predict the local convective mass transfer coefficients through the analogy between the thermal and concentration boundary layers (known as the Chilton–Colburn analogy). In addition, the time-dependent temperature and moisture distributions for different cases are obtained using the code developed to investigate heat and mass transfer aspects inside the fruits. Numerical results are then compared with experimental data and a considerably high agreement is obtained.     

Multipath channel identification by using global optimization in ambiguity function domain

A new transform domain array signal processing technique is proposed for identification of multipath communication channels. The received array element outputs are transformed to delay-Doppler domain by using the cross-ambiguity function (CAF) for efficient exploitation of the delay-Doppler diversity of the multipath components. Clusters of multipath components can be identified by using a simple amplitude thresholding in the delay-Doppler domain. Particle swarm optimization (PSO) can be used to identify parameters of the multipath components in each cluster. The performance of the proposed PSO-CAF technique is compared with the space alternating generalized expectation maximization (SAGE) technique and with a recently proposed PSO based technique at various SNR levels. Simulation results clearly quantify the superior performance of the PSO-CAF technique over the alternative techniques at all practically significant SNR levels.     

Design of systems for hydrogen production based on the Cu-Cl thermochemical water decomposition cycle: Configurations and performance

In this study, we analyze several Cu-Cl cycles by examining various design schemes for an overall system and its components, in order to identify potential performance improvements. The factors that determine the number and effective grouping of steps for new design schemes are analyzed. A thermodynamic analysis and several parametric studies are presented for various configurations. The energy efficiency is found to be 44% for the five-step thermochemical process, 43% for the four-step process and 41% for the three-step process, based on the lower heating value of hydrogen. Also, conclusions regarding implementation of these new configurations are discussed and the potential benefits ascertained.     

Bond Strength of a Silicone Soft Lining Material to Poly(methyl methacrylate) Resin Treated with Maleic Anhydride and its Terpolymers

This study investigated the effectiveness of surface treatment of Poly (methyl methacrylate) (PMMA) denture base resin on tensile bond strength between PMMA/silicone-based soft liner. A total of 25 specimens were fabricated and assigned into five groups (n = 5). The surfaces of PMMA were treated with maleic anhydride, maleic anhydride-styrene-vinyl-acetate, n-butylmaleate-styrene-vinyl-acetate, or n-pentamaleate-styrene-vinyl-acetate prior to Primo adhesive primer application and silicone liner placement. The Primo adhesive primer on applied group untreated dentuse base resin served as control. The tensile test was performed using a universal testing machine. Fractured surfaces were observed under Scanning Electron Microscopy (SEM) and spectroscopic interpretation of the interfaces was done by Fourier Transform Infrared (FTIR). Test results showed that surface treatment increased interfacial strength giving the highest value for n-butylmaleate-styrene-vinyl acetate treated group. SEM micrographs revealed that the specimens with n-butylmaleate-styrene-vinyl-acetate and n-penta maleate-styrene-vinyl-acetate terpolymers underwent cohesive failure. FTIR analysis indicated secondary interactions such as hydrogen bonding, possibly on acrylic resin surfaces, caused by the use of maleic anhydride and its terpolymers, and the adhesive.     

The effect of particle size distribution on the properties of blended cements incorporating GGBFS and natural pozzolan (NP)

This paper investigates the effect of particle size distribution on the properties of blended cements incorporating ground granulated blast-furnace slag (GGBFS) and natural pozzolan (NP). Pure Portland cement (PPC), NP and GGBFS were used to obtain blended cements that contain 10, 20, 30% additives. The cements were produced by intergrinding and separate grinding and then blending. Each group had two different Blaine fineness of 280 m²/g and 480 m²/g. According to the particle size distribution (PSD) curves, 46% of the coarser specimens and 69% of the finer specimens passed through the 20 μm sieve. It was observed that the separately ground specimens were relatively finer than the interground ones and had higher compressive strength and sulfate resistance. The separately ground coarser specimens had the lowest heat of hydration. The separately ground finer specimens, which had the highest compressive strength and sulfate resistance, had the highest percent passing for each sieve size. For these specimens 34, 69, 81 and 99% passed through 5, 20, 30 and 55 μm sieves, respectively. For the interground specimens, which had the same fineness, the respective values for the same sieves were 32, 68, 75 and 94%.     

On the drop-weight testing of alumina/aluminum laminated composites

Laminated composites with ceramic front layers and metallic or composite backing layers have gained attractiveness as lightweight armours, as they exhibit the same ballistic performance with lower areal densities as compared to steels. Drop-weight testing (DWT) has potential for evaluating the low velocity impact behaviour of materials. This testing gives significant ideas and information about failure mechanisms and behaviour of materials under low velocity impact. In this study, DWT of alumina/aluminum laminated composites was done in order to investigate the effects of lamination type, density with respect to area and mechanical property of backing material on the low velocity ballistic performance of these composites. The experimental results showed that the laminated composite with ceramic front layer and aged-aluminum alloy as backing layer was the most effective among different investigated specimens against low velocity impact loads.     

Antioxidant and anticholinesterase evaluation of selected Turkish Salvia species

Since Salvia species (Lamiaceae) have been recorded to be used against memory loss in European folk medicine, we herein examined in vitro anticholinesterase and antioxidant activities of 56 extracts prepared with petroleum ether, chloroform, ethyl acetate and methanol obtained from 14 Salvia species (Salvia albimaculata Hedge and Hub, Salvia aucheri Bentham var. canescens Boiss and Heldr, Salvia candidissima Vahl. ssp. occidentalis, Salvia ceratophylla L., Salvia cryptantha Montbret and Bentham, Salvia cyanescens Boiss and Bal., Salvia frigida Boiss, Salvia forskahlei L., Salvia halophilaHedge, Salvia migrostegia Boiss and Bal., Salvia multicaulis Vahl., Salvia sclarea L., Salvia syriaca L., Salvia verticillata L. ssp. amasiaca) growing in Turkey. The antioxidant activities were assessed by both chemical and enzymatic methods against 1,1-diphenyl-2-picrylhydrazyl (DPPH) radical-scavenging and xanthine/xanthine oxidase (XO) system generated superoxide anion radical inhibition. Anticholinesterase effect of the extracts was tested against both acetylcholinesterase (AChE) and butyrylcholinesterase (BChE) at concentrations of 0.2 and 1 mg/ml using a microplate-reader assay based on the Ellman method. Most of the extracts did not show any activity against AChE at 0.2 mg/ml, while the chloroform extracts had noticeable inhibition against BChE between 47.7% and 74.7%. The most active extracts at 1 mg/ml for AChE inhibition were observed to be petroleum ether extract of Salvia albimaculata (89.4%) and chloroform extract of Salvia cyanescens (80.2%), whereas ethyl acetate extracts of Salvia frigida and Salvia migrostegia, chloroform extracts of Salvia candidissima ssp. occidentalis and Salvia ceratophylla, as well as petroleum ether extract of Salvia cyanescens were found to inhibit potently BChE (92.2%, 89.6%, 91.1%, 91.3%, and 91.8%, respectively). Particularly, the ethyl acetate and methanol extracts were observed to be highly active against both DPPH and XO. Our data indicates that nonpolar extracts of Salvia species for anticholinesterase activity and the polar extracts for antioxidant activity are worth further phytochemical evaluation for identifying their active components.     

Measurement of wood grain angle, moisture content and density using microwaves

In many wood products manufacturing processes, it is important to ensure that the physical properties of the raw material lie within acceptable ranges and are measured reliably. It is also important for practical use that the measurement process is robust, low-maintenance, fast and preferably non-contacting. This paper describes the development and demonstration of a microwave system for simultaneously identifying wood grain angle, moisture and density. The method involves propagating a microwave beam through the wood and measuring the resulting depolarization, attenuation and phase shift. The wood physical properties can then be identified from these measurements. In a series of measurements, the prototype microwave system successfully identified wood grain angles for hemlock and Douglas fir respectively with standard errors of 0.9° and 2.5° (measured range = -90° to +90°), moisture content 1.2% and 1.9% (measured range = 7–28%), moisture density 3.7 kg/m³ and 7.9 kg/m³ (measured range = 40–150 kg/m³, and dry density 16 kg/m³ and 30 kg/m³ (measured range = 325–625 kg/m³).