A Priori Assessment of Customer Costs in Designing the Life Cycle of Complex Products

The basic stages in the life cycle of a batch of complex engineering products are considered: design, production, operation, and disposal. A priori cost assessment for each stage is discussed. The cost aggregation in the consideration of multiple stages is analyzed. Requirements on the assessment are formulated. Methodological and implementation aspects of the assessment tools are outlined. The conclusion is that it is expedient to predict the costs on the basis of mathematical models of the product batch in an operational environment. The integration of multiple cost estimates is addressed.     

Technological and sensorial properties of liquid nitrogen ice cream enriched with protein from brewing waste (trub)

Debittered trub (brewing waste) is an important source of protein source (70.26%). Trub and whey protein were used for 5% protein enrichment of ice cream frozen by liquid nitrogen. Three formulations were elaborated: ice cream standard (ICS), ice cream with whey protein (ICW) and ice cream with trub (ICT). Chemical composition, rheological properties, texture, overrun, melting rate, scanning electron microscopy and a sensorial test were performed. Results showed that ICT presented a higher viscosity, obtained on the upward curve up to 6.76 Pa s⁻¹, consistency index (22.96 (Pa s⁻¹)ⁿ), hysteresis area (140.40 mPa s⁻¹) and hardness (31113.33 g) but a lower melting rate (0.38 g min⁻¹), overrun (13.92%) and sensorial acceptability than the other formulations. The addition of trub debittered for protein enrichment improved ice cream properties and demonstrated that it could be used as a food ingredient.     

Extractive Separation of Oxalic and Nitric Acids Using Tributyl Phosphate

Theoretical Foundations of Chemical Engineering - The extraction of nitric and oxalic acids by neutral compounds TBP, DBBP, and TBPO have been studied. The optimal conditions of their separation...     

Long-term sensor measurements of lung deposited surface area of particulate matter emitted from local vehicular and residential wood combustion sources

Abstract

Lung deposited surface area (LDSA) is a relatively new metric that has been argued to be more accurate at predicting health effects from aerosol exposure. For typical atmospheric aerosol, the LDSA concentration depends mainly on the concentration of ultrafine particles (e.g. vehicular exhaust emissions and residential wood combustion) and therefore optical methods cannot be used to measure and quantify it. The objective of this study was to investigate and describe typical characteristics of LDSA under different urban environments and evaluate how a diffusion charging-based Pegasor AQ Urban sensor (Pegasor Ltd., Finland) can be used as an alternative to optical sensors when assessing local combustion emissions and respective LDSA concentrations. Long-term (12?months) sensor measurements of LDSA were carried out at three distinctly different measurement sites (four sensor nodes) in the Helsinki metropolitan area, Finland. The sites were affected mainly by vehicular exhaust emission (street canyon and urban background stations) and by residential wood combustion (two detached housing area stations). The results showed that the accuracy of the AQ Urban was good (R² = 0.90) for the measurement of LDSA when compared to differential mobility particle sizer. The mean concentrations of LDSA were more than twice as high at the street canyon (mean 22 µm² cm^?3) site when compared to the urban background site (mean 9.4 µm² cm^?3). In the detached housing area, the mean concentrations were 12 µm² cm^?3, and wood combustion typically caused high LDSA peaks in the evenings. High correlations and similar diurnal cycles were observed for the LDSA and black carbon at street canyon and urban background stations. The utilization of a small-scale sensor network (four nodes) showed that the cross-station variability in hourly LDSA concentrations was significant in every site, even within the same detached housing area (distance between the two sites ～670?m).     

Heuristic Solution to the Diffraction Problem on a Superconducting Half-Plane

Journal of Communications Technology and Electronics - Abstract—The article presents a rigorous numerical solution, using the Wiener–Hopf method, to the problem of plane wave...     

A self-adaptive synthetic over-sampling technique for imbalanced classification

Traditionally, in supervised machine learning, (a significant) part of the available data (usually 50%-80%) is used for training and the rest—for validation. In many problems, however, the data are highly imbalanced in regard to different classes or does not have good coverage of the feasible data space which, in turn, creates problems in validation and usage phase. In this paper, we propose a technique for synthesizing feasible and likely data to help balance the classes as well as to boost the performance in terms of confusion matrix as well as overall. The idea, in a nutshell, is to synthesize data samples in close vicinity to the actual data samples specifically for the less represented (minority) classes. This has also implications to the so-called fairness of machine learning. In this paper, we propose a specific method for synthesizing data in a way to balance the classes and boost the performance, especially of the minority classes. It is generic and can be applied to different base algorithms, for example, support vector machines, k-nearest neighbour classifiers deep neural, rule-based classifiers, decision trees, and so forth. The results demonstrated that (a) a significantly more balanced (and fair) classification results can be achieved and (b) that the overall performance as well as the performance per class measured by confusion matrix can be boosted. In addition, this approach can be very valuable for the cases when the number of actual available labelled data is small which itself is one of the problems of the contemporary machine learning.     

Influence of Sodium Microalloying on Rolling Contact Endurance and Mechanical Properties of Hot-Deformed Powder Steels

Russian Journal of Non-Ferrous Metals - Rolling bearing rings comprise a large reserve for expanding powder metallurgy production. This reserve is being incompletely implemented. The hot forging of...     

Related Oscillations of Plasmons in Two Similar Nanocylinders from Silver

Journal of Communications Technology and Electronics - Abstract—The two-dimensional diffraction problem of a plane polarized TM-wave on two identical solid silver nanocylinders is considered....     

Anomaly-Based Intrusion Detection System in RPL by Applying Stochastic and Evolutionary Game Models over IoT Environment

Wireless Personal Communications - The rapid development of Information and Communication Technology and the growing number of devices connected to the Internet make the Internet of Things (IoT) as...     

Chlorination of Quartz-Leucoxene Concentrate of Yarega Field

Metallurgical and Materials Transactions B - The process of obtaining titanium tetrachloride (TiCl4) from the quartz-leucoxene concentrate (QLC) from the Yaregskoe oil-titanium field was studied....