Comparison between the binding of chlorpheniramine maleate to poly(sodium 4-styrenesulfonate) and the binding to other polyelectrolytes

The interactions of the antihistaminic drug chlorpheniramine maleate (CPM) with the negatively charged polyelectrolytes poly(sodium 4-styrenesulfonate) (PSS) and poly(acrylic acid) (PAA) are studied by the washing method of the diafiltration technique at conditions simulating those of the small intestine such as pH 7.5 and 0.13 M NaCl. The results are compared with those already reported involving other pharmacologically important polyelectrolytes such as alginic acid (ALG), carboxymethylcellulose (CMC), and κ- and ι-carrageenan (κ- and ι-CAR). As in the case of ALG, CMC, and CAR, interactions of CPM with PAA appear to be electrostatic and are cleaved in the presence of 0.13 M NaCl. On the contrary, apart from electrostatic interactions, additional interactions are found with PSS and residual interactions are kept in the presence of 0.13 M NaCl, a fact that may be attributed to π-π interactions and hydrophobic forces. The effect of the addition of 4 M urea, branched poly(ethyleneimine) (BPEI), and poly(vinylpyrrolidone) (PVP) is also studied. The addition of urea 4 M or 0.001 M BPEI produces a decrease on the amounts of counterions bound to PSS at infinite elution, while the addition of PVP does not produce any change on the diafiltration profiles.     

High Pressure Conductivity and Photoconductivity of Polyveratrole

Summary Electropolymerization of o-(CH₃O)₂C₆H₄ (Veratrole) in dry acetonitrile/tetrabutylammonium tetrafluoroborate at platinum electrode, yields a green polymeric conducting solid. As the pressure is increased, the material becomes more conductive, but sharp changes towards lower conductivity occur at 4.2 and 6.2 metric tons pressure, probably due to phase transitions. The photoconductivity shows an exponential increase as temperature is increased, but it shows reversible changes at 200 K, 225 K and 250 K during slow warming, also attributable to phase transitions. Photoconductivity of Polyveratrole increases with the radiation frequency, being higher under blue light than under red of infrared radiation and there is a linear increase of photoconductivity with radiation density. Conductivity transients show that the conductivity increases exponentially with time to the saturation point within few minutes, and it also decreases exponentially when the light is turned off and the circuit is open. This behaviour can be explained by formation and encounter of electron and hole as current carriers. A preliminary study indicates a piezoelectric effect for the material. absorption spectroscopy allowed the measurements of the material band gap.     

3D Hair sketching for real-time dynamic & key frame animations

Physically based simulation of human hair is a well studied and well known problem. But the “pure” physically based representation of hair (and other animation elements) is not the only concern of the animators, who want to “control” the creation and animation phases of the content. This paper describes a sketch-based tool, with which a user can both create hair models with different styling parameters and produce animations of these created hair models using physically and key frame-based techniques. The model creation and animation production tasks are all performed with direct manipulation techniques in real-time.     

Robustness of classification rules that incorporate additional information

The discrimination problem for two normal populations with the same covariance matrix when additional information on the population is available is considered. A study of the robustness properties against training sample contamination of classification rules that incorporate this additional information is performed. These rules have received recently attention where their total misclassification probability (TMP) is proved to be lower than Fisher's linear discriminant rule. The results of a simulation study on the TMP which compares the behaviour of the new rules against Fisher's rule and some of its robustified versions under different types of contamination are presented. These results show that the rules that incorporate the additional information not only have lower TMP, but they also prevent against some types of contamination. In order to achieve prevention from all types of contamination a robustifed version of these rules is recommended.     

Elimination of organic matter present in wastewaters from the cork industry by membrane filtration

BACKGROUND: The first stage of the cork industrial process generates great volumes of wastewater with moderate to high organic pollutant content that must be purified using different procedures, such as filtration by membranes. RESULTS: The tangential filtration of these wastewaters was studied using two different laboratory equipments. In the first one, three ultrafiltration (UF) membranes were tested, with molecular weight cut‐off (MWCO) 100 kDa and 30 kDa, and two operating modes were used: total recycling of permeate and retentate streams, and in continuous mode, without recycling both streams. In the total recycling UF experiments, the influence of the operating variables on the permeate flux was first established. The effectiveness of the different membranes was determined by evaluating the rejection coefficients for several parameters that measure the global pollutant content of the effluent. The values found for these rejection coefficients were in the following order: ellagic acid and color > absorbance at 254 nm > tannic content > COD (chemical oxygen demand). In the continuous mode experiments, the fouling mechanism for each membrane was established by fitting the experimental data to various filtration fouling models given in the literature. The operating mode in the second equipment was batch concentration, and additional experiments were carried out with an UF membrane (2 kDa), and with a NF membrane (with MWCO in the range 150–300 Da). CONCLUSIONS: The three operating modes tested provided different rejection levels of organic matter; among them, the most effective procedure tested was batch concentration mode using a NF membrane. Copyright © 2007 Society of Chemical Industry     

Power sector development in India with CO2 emission targets: Effects of regional grid integration and the role of clean technologies

The power sector in India at present comprises of five separate regional electricity grids having practically no integrated operation in between them. This study analyses the utility planning, environmental and economical effects of integrated power sector development at the national level in which the regional electric grids are developed and operated as one integrated system. It also examines the effects of selected CO₂ emission reduction targets in the power sector and the role of renewable power generation technologies in India. The study shows that the integrated development and operation of the power system at the national level would reduce the total cost including fuel cost by 4912 million $, total capacity addition by 2784 MW, while the emission of CO₂, SO₂ and NO_x would be reduced by 231.6 (1.9%), 0.8 (0.9%), 0.4 (1.2%) million tons, respectively, during the planning horizon. Furthermore, the study shows that the expected unserved energy, one of the indices of generation system reliability, would decrease to 26 GWh under integrated national power system from 5158 GWh. As different levels of CO₂ emission reduction targets were imposed, there is a switching of generation from conventional coal plants to gas fired plants, clean coal technologies and nuclear based plants. As a result the capacity expansion cost has increased. It was found that wind power plant is most attractive and economical in the Indian perspective among the renewable options considered (Solar, wind and biomass). Copyright © 2003 John Wiley & Sons, Ltd.     

A simple polyol synthesis of silver metal nanopowder of uniform particles

Silver metal has been synthesized in form of a finely divided loose nanopowder, 10–30 nm particle sizes, using a simple polyol process. In hot water, polymer molecules of polyvinyl alcohol (PVA) induce Ag⁺ → Ag reaction as a weak reducer (suitable to control the final particle size), forming a nanofluid of Ag nanoparticles in situ dispersing in part of PVA molecules. Ag nanoparticles do not aggregate much when casting a viscous Ag–PVA nanofluid (hot) onto a substrate in thin laminates or films. Freestanding Ag–PVA films could be obtained of 1–5 mm thickness after drying at room temperature. Dried sample can be easily peeled from a silicate glass substrate. As small as 5–10 mm Ag–PVA pieces were heated in air in order to recollect Ag nanoparticles by burning off the polymer. At 300–400 °C, Ag–PVA disintegrates and encounters combustion in air, resulting in a pure Ag-powder. As analyzed by X-ray diffraction, a single crystalline phase of an Fm3m cubic crystal structure formed. Lattice parameter a = 0.4071 nm and density ρ = 10.61 g/cm³ compare well the bulk values a = 0.4086 nm and ρ = 10.50 g/cm³.     

Small-scale CDM projects in a competitive electricity industry: How good is a simplified baseline methodology?

Setting baseline emissions is one of the principal tasks involved in awarding credits for greenhouse gas emission (GHG) mitigation projects under the Clean Development Mechanism (CDM). An emission baseline has to be project-specific in order to be accurate. However, project-specific baseline calculations are subject to high transaction costs, which disadvantage small-scale projects. For this reason, the CDM-Executive Board (CDM-EB) has approved simplified baseline methodologies for selected small-scale CDM project categories. While the simplified methods help reduce the transaction cost, they may also result in inaccuracies in the estimation of emission reductions from CDM projects. The purpose of this paper is to present a rigorous economic scheduling method for calculating the GHG emission reduction in a hypothetical competitive electricity industry due to the operation of a renewable energy-based power plant under CDM and compare the GHG emission reduction derived from the rigorous method with that obtained from the use of a simplified (i.e., standardized) method approved by the CDM-EB. A key finding of the paper is that depending upon the level of power demand, prices of electricity and input fuels, the simplified method can lead to either significant overestimation or substantial underestimation of emission reduction due to the operation of renewable energy-based power projects in a competitive electricity industry.