Correction of cirrus effects in Sentinel-2 type of imagery

Optical satellite images are often contaminated with cirrus clouds. Thin cirrus can be detected with a channel at 1.38 μm, and an established cirrus removal method exists for visible/near-infrared (VNIR) channels in atmospheric window regions, which was demonstrated with Moderate Resolution Imaging Spectrometer (MODIS) data. This contribution addresses open issues of cirrus correction for Sentinel-2 type of instruments, that is, future spaceborne sensors such as Sentinel-2 or similar instruments. These issues are (i) an extension of the existing technique to account for cirrus during the water vapour retrieval (channel at 0.94 μm) and surface reflectance calculation to avoid reflectance artefacts at 0.94 μm, (ii) a discussion of options concerning cirrus removal in the short-wave infrared (SWIR, channels at 1.6 and 2.2 μm) region and (iii) an analysis of channel parallax (view angle) requirements to achieve a high-quality cirrus removal.     

ASTM E1989-98 - The New Instrument Control Standard

The new ASTM E1989-98 Laboratory Equipment Control Interface Specification (LECIS) is a robust standard definition of equipment behavior while under remote control. The goal of the standardization effort is to facilitate “plug-and-play” integration of laboratory automation with standard hardware behavior and software interfaces. The LECIS standardizes laboratory equipment behavior and a message passing scheme between the controller and equipment that synchronizes this behavior. Commercial adoption of this new standard is well under way.     

Mixed-ion linear actuation behaviour of polypyrrole

The linear actuation of polypyrrole (PPy) films polymerized at 0.85 V (versus Ag-wire) and −27 °C in propylene carbonate solutions of tetrabutylammonium trifluoromethanesulfonate (TBACF₃SO₃) was investigated in the same monomer-free electrolyte. The actuation properties were evaluated by electrochemomechanical deformation measurements (ECMD) during cyclic voltammetry and potential step experiments. The ECMD response revealed mixed-ion actuation behaviour for the film, namely the polymer film actuation was dominated by cation movement at potentials less than 0 V and anion movement at potentials greater than 0 V, with film lengthening seen at both potential extremes. It was found that the ratio of cathodic to anodic actuation can be modulated by the scan rate. Longer-term actuation (50 potential steps from −1 V to 0 V, or from 0 V to +1 V), indicated better film stability when cycled in the anodic region. Changing the electropolymerisation potential to a higher value of 1.2 V led to a modification in ECMD characteristics for the PPy/CF₃SO₃ films.     

Messung und Theorie der Wandschubspannung bei Zweiphasenströmung im Rohr

Zusammenfassung Im allgemeinen gilt es als selbstverst?ndlich, da? ein durch ein Rohr str?mendes Medium auf die Rohrwand eine Schubspannung in Richtung der Str?mung übertr?gt. Aus Versuchen und überlegungen geht jedoch hervor, da? bei Zweiphasenstr?mungen im Schwerefeld auf Grund der Vorg?nge an der Wand die Schubspannung u. U. der Hauptstromrichtung entgegengerichtet ist. Auch ergibt sich, da? die dynamisch, d. h. unter Einflu? der Reibung gemessene F?rderh?he einer Pumpe h?her als die hydrostatisch berechnete sein kann. VDI Mitteilung aus dem Institut für kalorische Apparate und K?ltetechnik der Eidgen?ssischen Technischen Hochschule Zürich Herrn Prof. Dr. phil.E. Justi zur Vollendung seines 60. Geburtstags gewidmet.     

Project organization and contract management

The conceptual set-up of project organizations before tendering and contracting and their development and review during contract fulfilment is much more than a primitive art, today. The project organization can be designed and tailored to the actual objectives, phase, services, works, contract partners, and environmental conditions. Highly qualified organizational work is adequate to the important tasks of quality assurance and to using human talents and effort effectively.     

The influence of the die and floating plug geometry on the drawing process of tubing

Nowadays, the development of tube drawing process with a floating plug technique has moved our limit up to the production of thick-walled tubes; production of which still belongs to marginal techniques which are different from drawing of standard tubes. The submitted paper is basically a survey of research in fundamental characteristics of tube drawing with a floating plug with the aim to summarize some important results from the theory, which have not yet been published in any English publication. The purpose of this survey is to fill the gap in English literature to promote transfer and exploitation of knowledge. Research in fundamental characteristics was further developed and conditions under which it is possible to draw thick-walled tubes are defined. Confirmed possibility of thick-walled tubes drawing with support provided by a floating plug having negative overlap is the result of theoretical study and practical verification, which enables further moving of drawing process limit.     

An assessment of discretizations for convection-dominated convection–diffusion equations

The performance of several numerical schemes for discretizing convection-dominated convection–diffusion equations will be investigated with respect to accuracy and efficiency. Accuracy is considered in measures which are of interest in applications. The study includes an exponentially fitted finite volume scheme, the Streamline-Upwind Petrov–Galerkin (SUPG) finite element method, a spurious oscillations at layers diminishing (SOLD) finite element method, a finite element method with continuous interior penalty (CIP) stabilization, a discontinuous Galerkin (DG) finite element method, and a total variation diminishing finite element method (FEMTVD). A detailed assessment of the schemes based on the Hemker example will be presented.     

Three-dimensional Visualization of the Magnetic Microstructure in Bulk Fe-6.6 Pct Si

Magnetic materials such as Fe-Si alloys are magnetized by the rearrangement of their magnetic microstructure and domain wall motion. Understanding magnetic microstructures in the interior of a ferromagnet is essential for the control and reduction of energy losses in electrical devices. The three-dimensional magnetic microstructure of solids is still unknown due to the lack of an appropriate observation technique, and the magnetic domain wall structure inside a ferromagnet has never been observed with sufficiently high resolution. The first observation of the 3D magnetic microstructure of an Fe-6.6 pct Si alloy with a high spatial resolution is reported. The domain walls known to exist inside positive anisotropy cubic materials, i.e., the 180-deg domain walls and the 90-deg domain walls, were analyzed for the first time. The structure and orientation of the domain walls were found to be very different from the prediction of current theoretic models.