Dynamic Faults in Random-Access-Memories: Concept, Fault Models and Tests

The ever increasing trend to reduce DPM levels of memories requires tests with very high fault coverage and low cost. This paper describes an important fault class, called dynamic faults, that cannot be ignored anymore. The dynamic fault behavior can take place in the absence of the static fault behavior, for which the conventional memory tests have been constructed. The concept of dynamic fault will be established and validated for both dynamic and static Random-Access-Memories. A systematic way to develop fault models for dynamic faults will be introduced. Further, it will be shown that conventional memory tests do not necessarily detect its dynamic faulty behavior, which has been shown to exist in real designs. The paper therefore also presents new memory tests to target the dynamic fault class.     

Numerical studies on a paradox for non-cooperative static load balancing in distributed computer systems

Numerical examples of a Braess-like paradox in which adding capacity to a distributed computer system may degrade the performance of all users in the system under non-cooperative optimization have been reported. Unlike the original Braess paradox, in the models examined, this behavior occurs only in the case of finitely many users and not in the case of infinite number of users and the degree of performance degradation can increase without bound. This study examines numerically some examples around the Braess-like paradox in a distributed computer system. In the numerical examples, it is observed that the worst-case degree of the paradox (WCDP) is largest in complete symmetry. The dependence of the WCDP on some system parameters is also examined.     

Cellulose nanocrystals reinforced poly(oxyethylene)

Nanocomposite materials were prepared from poly(oxyethylene) (POE) as the matrix and a stable aqueous suspension of cellulose nanocrystals extracted from tunicate as the reinforcing phase. After dissolving POE in water and mixing with the cellulose nanocrystals suspension, solid films were obtained by casting and evaporating the preparations. Resulting films were characterized using scanning electron microscopy, differential scanning calorimetry, thermogravimetric analysis and dynamic mechanical analysis. Favorable interactions between cellulose and POE were evidenced and assumed to be partially responsible for a decrease of the crystallinity of the matrix. A thermal stabilization of the nanocomposites for temperatures higher than the melting temperature of POE was reported and ascribed to the formation of a rigid cellulosic network within the matrix assumed to be governed by a percolation effect. The formation of this percolating network was not altered by the matrix crystallization process and filler/POE interactions.     

Plasticized nanocomposite polymer electrolytes based on poly(oxyethylene) and cellulose whiskers

Nanocomposite polymer electrolytes based on a plasticized high molecular weight poly(oxyethylene) (POE) reinforced with high aspect ratio cellulose nanoparticles were reported. The influence of tetra(ethylene) glycol dimethyl ether (TEGDME) as plasticizer is investigated. The study mainly focuses on the dynamic mechanical behavior and ionic conductivity performances. The miscibility of the blend POE/TEGDME was investigated using both thermal and mechanical investigations. Viable polymer electrolytes can be obtained from this combination, conciliating acceptable ionic conductivities and outstanding mechanical performances on a large temperature range.     

Economical evaluation of electricity generation considering externalities

The economics of renewable energy are the largest barrier to renewable penetration. Nevertheless, the strong desire to reduce environmental emissions is considered a great support for renewable energy sources. In this paper, a full analysis for the cost of the kWh of electricity generated from different systems actually used in Egypt is presented. Also renewable energy systems are proposed and their costs are analyzed. The analysis considers the external cost of emissions from different generating systems. A proposed large scale PV plant of 3.3 MW, and a wind farm 11.25 MW grid connected at different sites are investigated. A life cycle cost analysis for each system was performed using the present value criterion. The comparison results showed that wind energy generation has the lowest cost, followed by a combined cycle–natural gas fired system. A photovoltaic system still uses comparatively expensive technology for electricity generation; even when external costs are considered the capital cost of photovoltaic needs to be reduced by about 60% in order to be economically competitive.     

Performance evaluation of OFDM and single‐carrier systems using frequency domain equalization and phase modulation

In this paper, we study the performance of the continuous phase modulation (CPM)‐based orthogonal frequency division multiplexing (CPM‐OFDM) system. Also, we propose a CPM‐based single‐carrier frequency domain equalization (CPM‐SC‐FDE) structure for broadband wireless communication systems. The proposed structure combines the advantages of the low complexity of SC‐FDE, in addition to exploiting the channel frequency diversity and the power efficiency of CPM. Both the CPM‐OFDM system and the proposed system are implemented with FDE to avoid the complexity of the equalization. Two types of frequency domain equalizers are considered and compared for performance evaluation of both systems; the zero forcing (ZF) equalizer and the minimum mean square error (MMSE) equalizer. Simulation experiments are performed for a variety of multipath fading channels. Simulation results show that the performance of the CPM‐based systems with multipath fading is better than their performance with single path fading. The performance over a multipath channel is at least 5 and 12 dB better than the performance over a single path channel, for the CPM‐OFDM system and the proposed CPM‐SC‐FDE system, respectively. The results also show that, when CPM is utilized in SC‐FDE systems, they can outperform CPM‐OFDM systems by about 5 dB. Copyright © 2010 John Wiley & Sons, Ltd.     

Effect of the drying process on the nutritive value of milk. Part 1. Biochemical composition

Five different brands of instant dry whole milk that are most commonly used, and freeze dried milk were analyzed for nitrogen, fat, ash and 4 inorganic constituents and compared with human milk. The composition of the milks differed considerably. The protein content varied widely, ranging from 11.6 to 24.5%. Fat content did not differ widely, ranging from 24.9 to 29.5%. Freeze dried milk had the highest fat content (42.6%). Three out of the five brands of dry milk studied were spray dried and the remaining two were roller dried. All milks tested contained considerably more sodium, potassium, calcium and phosphorus solid than human milk, some of them the four fold amount of calcium and phosphorus.     

Hand infections due to non-cholera Vibrio after injuries from St Peter's fish (Tilapia zillii)

We report 49 patients with a wide variety of hand infections, which developed after injuries from St Peter's fish (Tilapia zillii). Twenty-eight of 36 patients who had been operated on had non-cholera Vibrio infections, all identified as Vibrio vulnificus. The course in these patients was characterized by rapid spread of the infection with progressive necrosis of the tendon sheath, subcutaneous tissues and the skin. Two of them required amputations but the others had satisfactory functional results. Thirteen other patients were managed nonoperatively with intravenous antibiotics and all of them recovered completely.     

Effects of Fluids on the Simulated Clinical-Dental Machining of a Glass Ceramic

Effects of fluids on material removal rate, chipping damage, and surface roughness in the simulated clinical-dental machining of a dental-type glass ceramic were investigated. Significant differences in removal rate were obtained among the fluids investigated, but only a 4 wt% boric acid solution gave a higher removal rate than conventionally used water. Chipping damage was substantially lower for the boric acid and an oil-emulsion coolant compared with other fluids tested. Surface roughness was independent of the fluids used. The results indicate that improvement can be achieved in both material removal rate and machining damage by the appropriate selection of coolant chemistry.