Properties of aqueous solutions of several salts of α,ω-alkanediol disulfates

Several salts of α,ω-sulfates, MO₃SO(CH₂)_n OSO₃M(n=12, 14, 16, 18, and M=Li, Na, and K) were prepared from the corresponding α,ω-alkane diols. The Krafft points of these α,ω-sulfates with common counterion as estimated by electroconductivity measurements increased with the increase of the hydrocarbon chain length, and the effect of the counterions on the Krafft points of the α,ω-sulfates with the same hydrocarbon chain length was in the order : Li<Na<K. Solutions of the α,ω-sulfates, except disodium dodecanediol disulfate, showed two break points corresponding to the first and second critical micelle concentration in each plot of the electroconductivity as a function of the concentration. The existence of the second break point suggested that another aggregation of rearrangement of the existing aggregates occurs in α,ω-sulfate solutions in addition to the usual micelle formation. The first and second break points of α,ω-sulfates with sodium counterion decreased logarithmically with increasing total number of methylene groups. The relationships were given as follows: log(first break point)=−0.138Nc−0.095; log(second break point)=−0.104Nc−0.251. The effect of the counterions upon the break points of α,ω-sulfates with the same hydrocarbon chain length was in accordance with their positions in the lyotropic series.     

Dynamic moduli for short fiber-CR composites

The dynamic moduli, E′ and E″, and tan δ for nylon–CR and PET–CR composites with unidirectional short fibers were studied as a function of temperature by using a Rheovibron. The temperature dependence of tan δ showed two dispersion peaks for nylon–CR composite. The peak at ?28°C corresponded to the main dispersion of CR and the peak at 100°C to the α-dispersion of nylon 6. For a PET-CR composite, in addition to the individual dispersion of CR and PET, a small and broad peak was observed at about 90°C. The angular dependence of E′ indicated that the short fibers assumed good orientation. The storage modulus for the composites was given by the parallel model as E′ = V_f′E_f + V_mE′_m., where E′_c, E′_f and E′_m were the storage modulus for the composite, fiber, and matrix and V_f and V_m were the volume fraction of fiber and matrix, respectively. In the transverse direction of fiber, the peak values of tan δ at ?28°C were given by the following equation; tan δ_c = tan δ_m ? δV_f, where tan δ_c and tan δ_m are the loss tangent for the composite and matrix, respectively, and α is coefficient depending on fiber type. The results indicated that a region with strong interaction was formed between fibers and CR matrix.     

An ergonomics study of thumb movements on smartphone touch screen

This study investigated the relationships between thumb muscle activity and thumb operating tasks on a smartphone touch screen with one-hand posture. Six muscles in the right thumb and forearm were targeted in this study, namely adductor pollicis, flexor pollicis brevis, abductor pollicis brevis (APB), abductor pollicis longus, first dorsal interosseous (FDI) and extensor digitorum. The performance measures showed that the thumb developed fatigue rapidly when tapping on smaller buttons (diameter: 9 mm compared with 3 mm), and moved more slowly in flexion–extension than in adduction–abduction orientation. Meanwhile, the electromyography and perceived exertion values of FDI significantly increased in small button and flexion–extension tasks, while those of APB were greater in the adduction–abduction task. This study reveals that muscle effort among thumb muscles on a touch screen smartphone varies according to the task, and suggests that the use of small touch buttons should be minimised for better thumb performance.     

Electrochemical reduction of nitrate on Pt(S)[n(1 1 1) × (1 1 1)] electrodes in perchloric acid solution

The electrochemical reduction of nitrate ion was studied by cyclic voltammetry on Pt(1 1 1) and [n(1 1 1) × (1 1 1)] stepped Pt surfaces, where n (=14, 10, 7, 6, 5, 4, 3, 2) is the number of terrace atoms, in 0.1 M HClO₄ + 10 mM KNO₃. The electrocatalytic nitrate reduction was found to hardly proceed on Pt(1 1 1) in the hydrogen adsorption region, while the electrocatalytic activity was improved with the increase in the step density. Inactivation was observed in the presence of adsorbed hydrogen or nitrate-derived reduced adsorbate, i.e. adsorbed NO, on (1 1 1) step sites. It was, therefore, concluded that the electrocatalytically active NO₃⁻ species does not adsorb on the (1 1 1) terraces but on the (1 1 1) monoatomic steps. The nitrate reduction current increased with the step density in a non-linear relationship. The overall current density at 0.21 V (RHE) corresponding to the peak potential of the main electrocatalytic nitrate reduction wave which was maximum at n = 2, abruptly increased with short terraces, i.e. n < 5, where the current wave of adsorbed hydrogen on the Pt stepped surface with comparatively narrow (1 1 1) terraces, denoted as H_nt, also appeared unmodified for n < 5 on voltammograms recorded in 0.1 M HClO₄ in the absence of nitrate.     

Mechanical Properties of Alumina/Silicon Carbide Whisker Composites

The improvement of mechanical properties of Al₂O₃/SiC whisker composites has been studied with emphasis on the effects of the whisker content and of the hot-pressing temperature. Mechanical properties such as fracture toughness and fracture strength increased with increasing whisker content up to 40 wt%. In the case of the high SiC whisker content of 40 wt%, fracture toughness of the sample hot-pressed at 1900° decreased significantly, in spite of densification, compared with one hot-pressed at 1850°. Fracture toughness strongly depended on the microstructure, especially the distribution of SiC whiskers rather than the grain size of the Al₂O₃ matrix.     

New method for selective growth of diamonds by microwave plasma chemical vapour deposition

Selective nucleation and deposition of diamonds were achieved on an SiO₂-patterned Si substrate. The substrate was pre-treated with an electric field in plasma to introduce diamond nuclei. This treatment did not affect the SiO₂ area. Consequently, diamonds grew only on the area where Si was exposed under the conventional conditions of diamond growth. The maximum nucleation density on the area of SiO₂was about 5 × 10⁷ cm⁻². The ratio of the selectivity was 2 × 10² or higher. This process will be useful and very promising for manufacturing diamond electronic devices.     

Decomposition of chlorofluorocarbons on TiO2ZrO2

The decomposition of chlorofluorocarbons (CFCs) in the presence of water was examined over a variety of solid acid catalysts. The TiO₂ZrO₂ catalyst was found to have the highest activity and longest life among the catalysts examined. The activity of the TiO₂ZrO₂ catalysts depended upon the content of TiO₂. At the contents of TiO₂ from 58 to 90 mole%, the TiO₂ZrO₂ catalysts exhibited high activity, and these catalysts were proven to contain TiZrO₄ crystal. From the study of the XRD peak intensity of the TiZrO₄ crystal, it was highest on the TZ-58 which contained 58 mole% of TiO₂, and decreased with increasing the content of TiO₂. Furthermore, the conversion of CFC113 measured at 673 K was highest at TZ-58, and decreased gradually with increasing TiO₂ content. Therefore, the TiZrO₄ crystal influences the activity of decomposition of CFC113. However, the TiO₂ZrO₂ catalyst was gradually deactivated during the reaction due to the elimination of titanium atoms. A good relationship was found between the activity on TiO₂ZrO₂ catalyst and bond energy of CCl in the compounds of chlorofluorocarbons and hydrochlorocarbons, suggesting that the rate controlling step was the cleavage of CCl bond.     

Effective Coke Removal in Methane to Benzene (MTB) Reaction on Mo/HZSM-5 Catalyst by H2 and H2O Co-addition to Methane

The catalytic dehydro-aromatization reaction over Mo/HZSM-5 catalyst was drastically stabilized by the co-addition of 5.4% H₂ and 1.8% H₂O to methane feed at 750 °C, 0.3 MPa and methane space velocity of 3000 mL g⁻¹ h⁻¹, suppressing the coke formation effectively, compared with single hydrogen or steam addition.     

Conversion of methane to syngas in a solid oxide fuel cell with Ni-SDC anode and LSGM electrolyte

A solid oxide fuel cell constructed from Ni-SDC anode and LSGM electrolyte was applied to the partial oxidation of methane to syngas (CO+H₂) at 700-800 °C with the merits of co-generation of electricity and controllable O₂ supply. It was found that the co-generated syngas at H₂/CO ratio of 1.4-2.0 varied with applied current densities, CH₄ flow rates and operating temperatures. The cell voltage at 100 mA cm⁻² and 800 °C was 0.90 V, i.e. about 90 mW cm⁻² power density could be obtained. The cell operating at 50 mA cm⁻² for 24 h almost showed no degradation of the cell performance. The observed carbon deposition seemed mainly taking place by CH₄ cracking reaction.     

Design of new catalysts for ecological high-quality transportation fuels by combinatorial computational chemistry and tight-binding quantum chemical molecular dynamics approaches

Recently, we introduced a concept of combinatorial chemistry to computational chemistry and proposed a new method called “combinatorial computational chemistry”, which enables us to perform a theoretical high-throughput screening of catalysts. In the present paper, we reviewed our recent application of our combinatorial computational chemistry approach to the design of new catalysts for high-quality transportation fuels. By using our combinatorial computational chemistry techniques, we succeeded to predict new catalysts for methanol synthesis and Fischer–Tropsch synthesis. Moreover, we have succeeded in the development of chemical reaction dynamics simulator based on our original tight-binding quantum chemical molecular dynamics method. This program realizes more than 5000 times acceleration compared to the regular first-principles molecular dynamics method. Electronic- and atomic-level information on the catalytic reaction dynamics at reaction temperatures significantly contributes the catalyst design and development. Hence, we also summarized our recent applications of the above quantum chemical molecular dynamics method to the clarification of the methanol synthesis dynamics in this review.