Improvement in thermal endurance of D-mannitol as phase-change material by impregnation into nanosized pores

This paper describes the control of the melting point and improvement of the thermal endurance of D-mannitol (melting point T_m = 440 K) as a phase-change material (PCM) by vacuum impregnation of the PCM into nanosized pores of porous SiO₂ grains. First, we examined the effects of the average pore size (D_P) of porous SiO₂ on T_m and latent heat (L) of PCM/SiO₂ composites. Second, we investigated the thermal endurance of the composites using constant temperature kinetics based on L of the PCM and composites. Third, we performed cyclic tests of melting and freezing on the composite to evaluate leakage of the PCM. Thermophysical properties of the samples were measured by differential scanning calorimetry, and the following results were obtained: (1) The impregnation ratio of the composites was 0.91–0.99; therefore, almost all pores were completely filled with the PCM. (2) T_m shifted to lower temperature with smaller D_P, reaching 413 K in case of the PCM/SiO₂ composite with a D_P of 11.6 nm (3) T_m was derived as a function of D_P from the Gibbs–Thomson equation taking into account the existence of a nonfreezing layer on the surface of the pore wall. (4) The duration of thermal degradation of the PCM/SiO₂ composite with D_P = 11.6 nm was three times longer than that of the pure PCM at a temperature that is 10 K more than each melting point. (5) The PCM/SiO₂ composite with D_P = 11.6 nm can use as a shape-stable PCM composite without leakage of PCM.     

Phase Relations and Volume Changes of Hafnia under High Pressure and High Temperature

Using multi-anvil high-pressure devices and synchrotron radiation, X-ray in situ observations of HfO₂ under high pressure and high temperature have been performed to investigate its phase relations and compression behavior. An orthorhombic phase (orthoI) is stable from 4 to 14.5 GPa below 1250°–1400°C and transforms to a tetragonal phase, which is one of the high-temperature forms of HfO₂, above these temperatures. Another orthorhombic phase (orthoII) with a cotunnite-type structure appears above 14.5 GPa. OrthoII is stable up to 1800°C at 21 GPa. OrthoII is quenchable to ambient conditions. The orthoI-to-orthoII transition is accompanied by ∼8 vol% decrease. The bulk moduli of orthoI and orthoII at room temperature are 220 and 312 GPa, respectively. This low compressibility of orthoII indicates that it is a potential candidate for very hard materials.     

Measurement of High-Temperature Elastic Properties of Ceramics Using a Laser Ultrasonic Method

Young's modulus and Poisson's ratio of SiC ceramics at temperatures >1400°C were obtained using a laser ultrasonics method that included a Fabry-Pérot interferometer (LUFP). At temperatures <1000°C, Young's modulus and Poisson's ratio measured using the LUFP method agreed well with those measured using standard contact methods, such as the resonance method and the ultrasonic pulse method. These results showed that the LUFP method is a powerful tool for measuring high-temperature elastic properties of advanced ceramics in a noncontact manner.     

Morphology‐dependent electrocatalytic activity of nanostructured Pt/C particles from hybrid aerosol–colloid process

An optimum nanostructure and pore size of catalyst supports is very important in achieving high catalytic performances. In this instance, we evaluated the effects of various carbon nanostructures on the catalytic performances of carbon‐supported platinum (Pt/C) electrocatalysts experimentally and numerically. The Pt/C catalysts were prepared using a hybrid method involving the preparation of dense, hollow, and porous nanostructured carbon particle via aerosol spray pyrolysis followed by microwave‐assisted Pt deposition. Electrochemical characterization of the catalysts showed that the porous Pt/C catalyst gave the best performance; its electrochemical surface area was much higher, more than twice than those of hollow or dense Pt/C. The effects of pore size on electrocatalysis were also studied. The results showed the importance of a balance between mesopores and macropores for effective catalysis with a high charge transfer rate. A fluid flow model showed that good oxygen transport contributed to the catalytic activity. © 2015 American Institute of Chemical Engineers AIChE J, 62: 440–450, 2016     

Characterization of alternative plasticizers in poly(vinyl chloride) sheets for blood containers

This study aimed to optimize the ratio of dioctyl 4‐cyclohexene‐1,2‐dicarboxylate (DOTH) and di‐isononyl‐cyclohexane‐1,2‐dicarboxylate (DINCH^®) for use as plasticizers in poly(vinyl chloride) (PVC) sheets. We also evaluated the biological safety of DOTH for its potential to be part of a safe PVC‐based blood container. The suppression of hemolysis in mannitol‐adenine‐phosphate / red cell concentrates (MAP/RCC) with DOTH/(DINCH^®‐PVC) sheets and the elution of plasticizers from the sheets increased with higher DOTH compositions. The properties of the PVC sheet containing DOTH and DINCH^® in the ratio of 25:33 parts against PVC 100 parts as a weight were almost identical to the PVC sheet made of di(2‐ethylhexyl) phthalate. From a subchronic toxicity test, DOTH did not show any adverse effects on all organs, including the testes, epididymis, liver, and kidneys. The no‐observed‐adverse‐effect level was 300 mg/kg body weight/day in a rat. These results suggest that DOTH/DINCH^® (25:33) is a promising candidate for the replacement of di(2‐ethylhexyl) phthalate in blood containers. J. VINYL ADDIT. TECHNOL., 22:520–528, 2016. © 2015 Society of Plastics Engineers     

Homogeneous Strain Introduction Using Reciprocation Technique in High-Pressure Sliding

Metallurgical and Materials Transactions A - This study examines strain distribution occurring in the high-pressure sliding (HPS) processing for rods of pure Al and an AZ61 alloy. The strain...     

Effects of V content on hydrogen storage properties of V–Ti–Cr alloys with high desorption pressure

Hydrogen storage is one of the most important issues to realize hydrogen society especially for on-board usage. Recently, high-pressure metal hydride (MH) tank attracts many attentions due to its high volumetric hydrogen storage density and relatively easy heat management. To emphasize its merits, further improvements of properties of MH, such as capacity, hydrogen desorption capability at low temperature and durability, are required. In this paper, V–Ti–Cr alloys of V-rich compositions were investigated with perspective of increasing of hydrogen desorption pressure and durability. In both of 60at%V–Ti–Cr and 80at%V–Ti–Cr alloys, good relationship between hydrogen desorption pressure and Ti content was observed. In comparing with 60at%V–Ti–Cr alloys, 80at%V–Ti–Cr alloys showed good durability. It is quite notable that relationship between limitation line (upper substitution limit of Ti by Cr without degradation of hydrogen capacity) and desorption pressure for V–Ti–Cr ternary system with V-rich composition is clarified. And also, it is revealed that in the case of V–Ti–Cr ternary system, not only Ti/Cr ratio but also V content is important factor to obtain alloys with high hydrogen desorption pressure. 75at%V–5at%Ti–Cr as-cast sample showed good durability, hydrogen desorption capability at low temperature and relatively high effective hydrogen capacity simultaneously.