基于状态空间法的电动机故障诊断和识别

电动机的初期故障信号一般较弱,不易辨别,而状态空间法在小信号的处理中灵敏度很高。为达到对电动机故障的诊断和识别,试图把状态空间法应用到对电动机的故障诊断中,先通过推导,从数学理论层面分析了状态空间法对于电动机故障信号的可辨别性,再使用Matlab软件搭建状态空间的辨别模型,把实验台测试的三组数据导入到模型中进行测试。测试的结果有力地证明了此方法的可行性,并能克服快速傅里叶变换(FFT)中数据采集量较大、分辨率不高的缺点。     

回字形环山地建筑结构设计

中央美院青岛创业中心项目为角部重叠的回字形山地建筑,采用了框架-剪力墙结构体系.主体建筑结构总高度为54m,坐落在三个台地上,每两个相邻台地高差10m左右.掉层处采用"掉层脱开式且有拉梁"的方式进行结构布置.结合山地建筑结构的基本概念和受力特点,介绍了本项目的结构处理方式和设计难点,采用PKPM,MIDAS Building,SAUSAGE软件对结构进行了弹性反应谱法分析、弹性时程分析、动力弹塑性时程分析和抗震性能设计,同时针对各种不利因素采取了相应的加强措施,确保了结构安全.     

Three‐dimensional color prediction modeling of single‐ and double‐layered woven fabrics

In this research, the three‐dimensional structural and colorimetric modeling of three‐dimensional woven fabrics was conducted for accurate color predictions. One‐hundred forty single‐ and double‐layered woven samples in a wide range of colors were produced. With the consideration of their three‐dimensional structural parameters, three‐dimensional color prediction models, K/S‐, R‐, and L*a*b*‐based models, were developed through the optimization of previous two‐dimensional models which have been reported to be the three most accurate models for single‐layered woven structures. The accuracy of the new three‐dimensional models was evaluated by calculating the color differences ΔL*, ΔC*, Δh°, and ΔE_CMC(2:1) between the measured and the predicted colors of the samples, and then the error values were compared to those of the two‐dimensional models. As a result, there has been an overall improvement in color predictions of all models with a decrease in ΔE_CMC(2:1) from 10.30 to 5.25 units on average after the three‐dimensional modeling.     

Ferroelastic domain structure and phase transition in single-crystalline [PbZn1/3Nb2/3O3]1-x[PbTiO3]x observed via in situ x-ray microbeam

(1-x)Pb(Zn_1/3Nb_2/3)O₃-xPbTiO₃ ((1-x)PZN-xPT in short) is one of the most important piezoelectric materials. In this work, we extensively investigated (1-x)PZN-xPT (x = 0.07–0.11) ferroelectric single crystals using in-situ synchrotron μXRD, complemented by TEM and PFM, to correlate microstructures with phase transitions. The results reveal that (i) at 25 °C, the equilibrium state of (1-x)PZN-xPT is a metastable orthorhombic phase for x = 0.07 and 0.08, while it shows coexistence of orthorhombic and tetragonal phases for x = 0.09 and x = 0.11, with all ferroelectric phases accompanied by ferroelastic domains; (ii) upon heating, the phase transformation in x = 0.07 is Orthorhombic → Monoclinic → Tetragonal → Cubic. The coexistence of ferroelectric tetragonal and paraelectric cubic phases was in-situ observed in x = 0.08 above Curie temperature (T_C), and (iii) phase transition can be explained by the evolution of the ferroelectric and ferroelastic domains. These results disclose that (1-x)PZN-xPT are in an unstable regime, which is possible factor for its anomalous dielectric response and high piezoelectric coefficient.     

一种2,6-二甲基苯甲酸的改进合成方法

以2,6-二甲基苯胺为原料,通过重氮化反应制备2,6-二甲基苯腈,经水蒸汽蒸馏法提纯后,采用75%硫酸酸化,再经酸碱法对产物进行脱色和纯化得产物2,6-二甲基苯甲酸,总收率68.4%。工艺简单、操作安全、适合工业化生产。     

Structures and properties of chicken myofibrillar protein gel induced by microwave heating

Structures and properties of myofibrillar protein gel prepared at different power (300–800 W) were evaluated. Amino acid analysis demonstrated that changes in microwave power did not alter primary structure of gel. However, an increase in microwave power could change higher structures of gel. As microwave power increased, α-helix content decreased and β-sheet content increased. Increased microwave power probably facilitated protein to unfold and expose the internal groups, causing surface hydrophobicity and the formation of disulphide bonds were enhanced, which indicated changes in tertiary and quaternary structures of protein. At 500 W, gel had the best ultrastructure where surface morphology, springiness and water holding capacity reached the optimum. Our findings suggested that microwave at an appropriate power (500 W) could change higher structures of myofibrillar protein gel to achieve desired processing and quality protein gel characteristics.     

Effect of stoichiometry and Cu-substitution on the phase structure and hydrogen storage properties of Ml-Mg-Ni-based alloys

To improve the electrochemical properties of rare-earth–Mg–Ni-based hydrogen storage alloys, the effects of stoichiometry and Cu-substitution on the phase structure and thermodynamic properties of the ...     

Preparation of biaxially textured Ce1-x(Y0.2Zr0.8)xOδ buffer layers on RABiTS NiW tapes by chemical solution deposition

Highly (100)-oriented Ce_1-x(Y_0.2Zr_0.8)_xO_δ (CYZO) films were prepared on biaxially textured NiW substrates by a chemical solution deposition approach using metal inorganic salts as starting materials. It has been found that both the preferential orientation and surface roughness of CYZO films decrease gradually with increasing of the doping percentage of Y³⁺ and Zr⁴⁺ ions. The epitaxial growth relationship of (220)_CYZO//(200)_NiW and [00?l]_CYZO//[001]_NiW was demonstrated by XRD texture measurement as well as atomic resolution STEM observation. XRD, Raman and XPS spectra results indicate that Y³⁺ and Zr⁴⁺ ions were indeed introduced into CeO₂ lattice to substitute Ce⁴⁺ ions and form cubic fluorite CYZO solid solution. Moreover, CeO₂ buffer layer can be endowed a strong enough capability to prevent element diffusion through co-doping of yttrium and zirconium, provided that an optimal doping ratio of them is adopted. This will provide a new approach to fabricating strong-barrier single buffer layer for coated conductor.