Continuous Flow Fabrication of Block Copolymer–Grafted Silica Micro‐Particles in Environmentally Friendly Water/Ethanol Media

Polymer‐grafted inorganic particles (PGIPs) are attractive building blocks for numerous chemical and material applications. Surface‐initiated controlled radical polymerization (SI‐CRP) is the most feasible method to fabricate PGIPs. However, a conventional in‐batch reaction still suffers from several disadvantages, including time‐consuming purification processes, low grafting efficiency, and possible gelation problems. Herein, a facile method is demonstrated to synthesize block copolymer–grafted inorganic particles, that is, poly(poly(ethylene glycol) methyl ether methacrylate) (PPEGMEMA)‐b‐poly(N‐isopropylacrylamide) (PNIPAM)–grafted silica micro‐particles using continuous flow chemistry in an environmentally friendly aqueous media. Immobilizing the chain transfer agent and subsequent SI‐CRP can be accomplished sequentially in a continuous flow system, avoiding multi‐step purification processes in between. The chain length (MW) of the grafted polymers is tunable by adjusting the flow time or monomer concentration, and the narrower molar mass dispersity (Р< 1.4) of the grafted polymers reveals the uniform polymer chains on the particles. Moreover, compared with the in‐batch reaction at the same condition, the continuous system also suppresses possible gelation problems.     

基于材料力学性能的最低设计金属温度曲线分析

铁素体钢在低温条件下存在明显的韧脆转变现象。为防止脆断事故的发生,需要确定铁素体钢制压力容器的最低使用温度。针对ASME中的A^D四条冲击豁免曲线,对应地选取了4种材料,基于材料实际的屈服强度和参考温度,按照ASME中豁免曲线的计算方法,计算得到4种材料的最低设计金属温度曲线,并与对应的A^D曲线对比,定量地分析ASME中豁免曲线的保守性。结果表明,ASME中的豁免曲线相对于材料自身的最低设计金属温度曲线保守性较大;韧性相近的材料被划分到不同的豁免曲线,使得韧性富裕量差异较大,对于某些材料,其断裂韧性被低估。     

Structural modification of aminoclay for catalytic applications

Abstract

An eco-friendly catalyst system was synthesized using three step reaction. The Cu nanoparticles bridged aminoclay catalyst was analyzed using various analytical techniques. The structure of the catalyst was confirmed by FTIR and XRD. The synthesized catalyst system was used for the reduction of p-nitrophenol (NP), Cr(VI), and fluorescein (Flur) dye individually, as well as in their mixture forms. The k_app value was computed to access the efficiency of the catalyst. The results indicated that the k_app value of the individual system is higher than that of the mixture systems due to the absence of the complex formation reaction. The catalytic performance of the catalyst was also tested for the Schiff base (SB) formation between poly(ethyleneglycol) (PEG) and aniline (ANI) in an oxygen atmosphere. The ¹H-NMR spectroscopy result indicates that the present catalyst system produced 86% yield.     

Effect of nanoparticles orientation on morphology of polymeric nanocomposite foams: preparation of foamed nanocomposite fibers by supercritical carbon dioxide

ABSTRACT

Polymeric foams have received increasing attention in both academic and industrial communities. Using of nanoparticles as heterogeneous nucleation agent has been verified as one of the most valid means to enhance cell nucleation and improve cell morphology. However, few researches have been conducted to investigate the effect of the nanoparticles’ spatial orientation on their nucleation efficiency. In this work, to study the influence of the orientation of nanoparticles on their performance in improving morphology of polymeric foam, thermoplastic polyurethane (TPU) composite fibers with different nanoparticles (carbon nanotubes, graphene and SiO₂) were prepared by using different traction speeds. The different traction speeds lead to different orientation state of the nanoparticles which then resulted different nucleation effect. It was found that carbon nanotubes (CNTs) were easily oriented and aligned along the fiber length direction under the high traction speed, while graphene and SiO₂ nanoparticles did not show orientation under the traction speed in this study. As a result, the foam of TPU/CNTs composite fibers from high traction speed exhibited a much smaller cell size and higher cell density compared to the foams of the fibers from low traction speeds, while TPU/graphene, and TPU/SiO₂ composite fibers with different traction speeds showed almost similar cell size and size density after foaming, indicating that the orientated nanoparticles possessed higher heterogeneous nucleation efficiency. To our best knowledge, this work, for the first time, demonstrated the high nucleation effect of the aligned nanoparticles, which hopefully open a new path for improving the cell morphology of polymeric foam materials.     

客车涂装底层材料配套性分析

针对南方客户在使用我司客车一段时间后，车身涂层不同程度出现了起泡的质量问题，进行了现场查看，发现起泡位置在车身左右侧蒙皮，且发生在涂层最底层。初步分析原因是热镀锌板+阴极电泳漆 +原子灰三者之间配套存在问题，通过热镀锌板 +阴极电泳漆 +原子灰三者之间的耐高温 80 ℃配套试验，以及室外曝晒试验，得出镀锌板表面是否钝化、电泳漆膜致密程度和原子灰苯乙烯含量是造成涂层底层起泡的主要原因。为了控制涂层起泡问题，重新修订了我司原子灰、镀锌板、电泳漆的技术标准以及部分工艺文件。     

Simultaneous improvement of thermal conductivity and mechanical properties for mechanically mixed ABS/h-BN composites by using small amounts of hyperbranched polymer additives

Recently, thermal interface materials (TIMs) are in great demands for modern electronics. For mechanically mixed polymer composite TIMs, the thermal conductivity and the mechanical properties are generally lower than expected values due to the sharply increased viscosity and poor filler dispersion. This work shows that addition of a small amount of polyester-based hyperbranched polymer (HBP) avoided the trade-off in mechanically mixed ABS/hexagonal boron nitride (h-BN) composites. After adding 0.5 wt% HBP, the maximum h-BN content in the composites increased from 50 to 60 wt%. The out-of-plane, in-plane thermal conductivity, and tensile strength of ABS/h-BN with 50 wt% h-BN were 0.408, 0.517 W/mK, and 18 MPa, respectively, and were increased to 0.729, 0.847 W/mK, and 32 MPa by adding 0.5 wt% HBP, while 0.972, 1.12 W/mK, and 29.5 MPa were achieved for ABS/h-BN/HBP with 60 wt% h-BN. The morphological and rheological results proved that these enhancements are due to the improved h-BN dispersion by decreasing viscosity of composites during mixing. Theoretical modeling based on the modified effective medium theory confirmed such results and showed that the interfacial thermal resistance also decreased slightly. Thus, this work demonstrates a facile and scalable method for simultaneously improving the thermal conductivity and mechanical properties of thermoplastic-based TIMs.     

折臂式随车起重机转台的拓扑优化设计

为了使折臂式随车起重机转台在最大应力不超过材料许用应力的前提下实现轻量化设计的目的,通过ADAMS软件仿真确定其极限工况,对转台进行静力学分析及拓扑优化。通过拓扑优化得到了理想的材料分布。基于优化结果调整转台结构,并对改进后的转台进行静力学分析。结果表明,优化后的转台能够满足实际的使用需求。同时,转台质量降低了12%,证明了优化设计的有效性和可行性,并为折臂式随车起重机的相关设计提供了一定的借鉴。     

胡海陶瓷艺术作品选登

正~~     

Eight-node conforming straight-side quadrilateral element with high-order completeness (QH8-C1)

A new eight-node conforming quadrilateral element with high-order completeness, denoted as QH8-C1, is proposed in this article. First, expressions for the interpolation displacement function satisfying the requirements for high-order completeness in the global coordinate system are constructed. Second, the displacement function expression in global coordinates is transformed into isoparametric coordinates, and the relationships between the two series of coefficients for the two kinds of displacement function expressions are found. Third, the displacement function expression is modified to satisfy the requirements of nodal freedom and interelement boundary continuity. The key to the new element construction is the derivation of the linear relationship expressions among 12 coefficients of element displacement interpolation polynomials in the global and isoparametric coordinate systems. As a result, the relationship between quadratic completeness and interelement continuity is explicitly given, and a proof of the completeness and the continuity was conducted to theoretically guarantee the validity of the derivation results. Furthermore, in order to verify the correctness of the theoretical work, nine numerical examples were performed. The computation results from these examples demonstrate that QH8-C1 exhibited excellent performance, including high simulation accuracy, fast convergence, insensitivity to mesh distortion, and monotonic convergence.