A new equation of state to predict S-CO<Subscript>2</Subscript> flow with real gas effects

The accuracy of the thermodynamic properties prediction from the different Equation of state (EOS) varies upon the range of temperature and pressure. Despite the variety of EOS available, there is no de facto for selecting an EOS for particular computational modeling. The EOS model recently developed by Kumar and Kim (K-K EOS) determines more accurately the thermodynamic properties of CO₂ than earlier models. In this present study, K-K EOS is successfully implemented in the computational analysis of compressible supercritical CO₂ flow (S-CO₂) in the thermodynamic region near and away from the vapour-liquid critical point. Computational results of SCO₂ flow with the real gas properties predicted with the K-K EOS is compared with Span and Wagner (SW EOS) and ideal EOS.     

Numerical investigation of heat transfer and friction factor in ribbed triangular duct solar air heater using Computational fluid dynamics (CFD)

Journal of Mechanical Science and Technology - The Computational fluid dynamics (CFD) based analysis is carried out to investigate the thermal and hydraulic performance of circular rib roughened...     

Surfactant controlled lubricity of paraffin oil-based nano-emulsion

Oil-in-water emulsions are used as metalworking fluids (MWFs). Considering the environmental issues and operator's health, the amount of oil-in-MWFs is one of the important parameters. In the present study, paraffin oil is used for emulsion formulation and possibilities to minimize the amount of paraffin oil-in-MWFs are explored. Physical characterization of emulsions is done using dynamic light scattering and goniometer. The tribological response of emulsions is recorded using the Four-ball tester. Results indicate that the amount of oil can be brought down to a level of 0.5% v/v to achieve the standard friction level. Droplet size and distribution seems to control the lubricity of emulsions, smaller droplets are desired for better lubrication.     

Dry machining of aluminum for proper selection of cutting tool: tool performance and tool wear

Machining of aluminum and its alloy is very difficult due to the adhesion and diffusion of aluminum, thus the formation of built-up edge (BUE) on the surface. The BUE, which affects the surface integrity and tool life significantly, affects the service and performance of the workpiece. The minimization of BUE was carried out by selection of proper cutting speed, feed, depth of cut, and cutting tool material. This paper presents machining of rolled aluminum at cutting speeds of 336, 426, and 540 m/min, the feeds of 0.045, 0.06, and 0.09 mm/rev, and a constant depth of cut of 0.2 mm in dry condition. Five cutting tools WC SPUN grade, WC SPGN grade, WC + PVD (physical vapor deposition) TiN coating, WC + Ti (C, N) + Al₂O₃ PVD multilayer coatings, and PCD (polycrystalline diamond) were utilized for the experiments. The surface roughness produced, total flank wear, and cut chip thicknesses were measured. The characterization of the tool was carried out by a scanning electron microscope (SEM) equipped with energy-dispersive X-ray spectroscopy (EDS) and X-ray diffraction (XRD) pattern. The chip underface was analyzed for the study of chip deformation produced after machining. The results indicated that the PCD tool provides better results in terms of roughness, tool wear, and smoother chip underface. It provides promising results in all aspects.     

Low Cost Porous Alumina with Tailored Microstructure and Thermal Conductivity Prepared using Rice Husk and Sucrose

This study demonstrates a cost‐effective way to fabricate porous ceramics with tailored porosity and pore microstructure using 5–40 wt% rice husk (RH) in <75 μm, 75–180 μm, 180–355 μm, 355–420 μm, and 420–600 μm size, as pore former. Sucrose, used as binder, also acted as a pore former. Porous alumina compacts with 20%–66% volume fraction porosity and 50–516 μm pore size (length) were successfully fabricated. Microstructure of samples reveal randomly oriented elongated coarse pores and fine pores (avg. size 4 μm), created during burnout of RH and sucrose, respectively. Samples with isolated and/or interconnected pores were fabricated using this process. Thermal conductivity of the samples prepared was measured using Transient Plane Source (TPS) technique. Thermal conductivity ranges from 1.2 to 24 W/mK. Experimental results agree closely with predictions made based on Effective Medium Theory (EMT) for a two‐phase system.     

Poly(ethyleneterephthalate) glycolysates as effective toughening agents for epoxy resin

The potential of poly(ethyleneterephthalate) glycolysates toward improving the energy absorption characteristics of cycloaliphatic epoxy resins has been explored. Microwave‐assisted glycolytic depolymerization of PET was performed in the presence of polyether diols of different molecular weights. The obtained glycolysates were blended with epoxy, and their mechanical properties were studied under both quasi‐static and dynamic conditions. Significant improvements were observed, which were found to depend both on the amount as well as nature of glycolysate. Amine functionalities were introduced at the terminal positions of glycolysates to improve the compatibility between the two phases. The amine derivatives exhibited superior performance and the Mode I fracture toughness (K_IC) of epoxy increased by ～18% in optimized compositions, which is indicative of its improved notch sensitivity. Neat epoxy specimens fractured in a brittle fashion, but all the blends exhibited ductile failure, as evidenced by surface morphological investigations. The mechanical properties of epoxy blends prepared with analogous aliphatic polyols, both before and after amine functionalization, were also studied which clearly reveal the beneficial role of aromatic groups toward improving the toughness of the base cycloaliphatic epoxy resin without compromising on the material stiffness. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39941.     

pH‐sensitive crosslinked guar gum‐based superabsorbent hydrogels: Swelling response in simulated environments and water retention behavior in plant growth media

Crosslinked guar gum‐g‐polyacrylate (cl‐GG‐g‐PA) superabsorbent hydrogels were prepared to explore their potential as soil conditioners and carriers. The hydrogels were prepared by in situ grafting polymerization and crosslinking of acrylamide onto a natural GG followed by hydrolysis. Microwave‐initiated synthesis under the chosen experimental conditions did not exhibit any significant improvement over the conventional technique. The optimization studies of various synthesis parameters, namely, monomer concentration, crosslinker concentration, initiator concentration, quantity of water per unit reaction mass, particle size of backbone, and concentration of alkali were performed. The hydrogels were characterized by wide‐angle X‐ray diffraction, scanning electron microscopy, Fourier transform infrared spectroscopy, and solid‐state ¹³C‐NMR spectroscopy. Swelling behavior of a candidate hydrogel [GG‐superabsorbent polymer (SAP)] in response to external stimuli, namely, salt solutions, fertilizer solutions, temperature, and pH, was studied. The GG‐SAP exhibited significant swelling in various environments. The effect of GG‐SAP on water absorption and the retention characteristics of sandy loam soil and soil‐less medium were also studied as a function of temperature and moisture tensions. The addition of GG‐SAP significantly improved the moisture characteristics of plant growth media (both soil and soil‐less), showing that it has tremendous potential for diverse applications in moisture stress agriculture. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41060.     

Soluble‐eggshell‐membrane‐protein‐modified porous silk fibroin scaffolds with enhanced cell adhesion and proliferation properties

In this study, a porous silk fibroin (SF) scaffold was modified with soluble eggshell membrane protein (SEP) with the aim of improving the cell affinity properties of the scaffold for tissue regeneration. The pore size and porosity of the prepared scaffold were in the ranges 200–300 μm and 85–90%, respectively. The existence of SEP on the scaffold surface and the structural and thermal stability were confirmed by energy‐dispersive X‐ray spectroscopy, X‐ray diffraction, Fourier transform infrared spectroscopy, differential scanning calorimetry, and thermogravimetric analysis. The cell culture study indicated a significant improvement in the cell adhesion and proliferation of mesenchymal stem cells (MSCs) on the SF scaffold modified with SEP. The cytocompatibility of the SEP‐conjugated SF scaffold was confirmed by a 3‐(4,5‐dimethyltriazol‐2‐y1)‐2,5‐diphenyl tetrazolium assay. Thus, this study demonstrated that the biomimic properties of the scaffold could be enhanced by surface modification with SEP. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40138.