不同分子量聚酯的羟值分析方法

用醋酐／高氯酸／乙酸乙酯法，醋酐吡啶回流法，分别对相对分子质量为１１００－１２０００的聚酯进行了羟值的测定，并用气压渗透法和析出物溶解重滴法进行了核对。结果表明醋酐／高氯酸／乙酸乙酯法对于Ｍ〈５０００的聚酯是适用的，而高分子量的聚酯则必须用醋酐／吡啶回流法，才能获得满意的结果。     

RT-PCR法检测庚型肝炎病毒C(GBV-C)RNA

应用RT－PCR法在非甲～非戊型肝炎患者血清及单采浆站供血员血浆中检测到GBV－CRNA，扩增产物经序列测定进一步确证，在30例非甲～非戊型肝炎患者中阳性率为6．6％；在600例单采浆供血者血浆中阳性率为0．33％。提示GBV－C可能不是非甲～非戊型肝炎的主要致病因子，可能存在GBV－C健康携带者。     

水解-水热法低温制备金红石型TiO2纳米颗粒研究

以硫酸钛为原料,通过水解-水热反应,在较低温度下制备出金红石型TiO2纳米颗粒.利用XRD和TEM研究了其结晶度、晶型和粒度情况和水热反应温度、保温时间、升温速度以及前驱物的pH值之间的关系,比较了常规条件和水热条件下反应产物的状况,并探讨了水热条件下晶相转化机理,以及控制晶相的关键因素。     

连续式双膜分离塔的数学模型

本文建立了适用于连续式双膜分离塔的数学模型。用实验数据验证了数学模型的可行性和合理性。将本模型与已发表的模型进行了比较,结果表明本模型具有形式简单、计算方便和适用范围更宽广等优点。     

Rheological study on O−carboxymethylated chitosan/cellulose polyblends from LiCl/N,N‐dimethylacetamide solution

An O?carboxymethylated chitosan (O? CMCh) water solution (I) and N,N‐dimethylacetamide (DMAc) emulsion (II) were blended with a cellulose LiCl/DMAc solution, and corresponding polyblends (Polyblends I and II) were obtained. The rheology of the three fluids, that is, the cellulose solution and Polyblends I and II, was investigated. The cellulose solution was characterized by a power‐law fluid. When an O‐CMCh water solution or DMAc emulsion was added to the cellulose solution, the power‐law curve was preserved. The power‐law indexes (n) of all three fluids increased along with the temperature. Polyblend I displays an n close to but a little higher than that of the cellulose solution, while Polyblend II shows a much higher power index than those of the other two fluids. The values of the apparent viscosity (η_a) for all the three fluids are close and decrease along with an increase in the temperature. Adding O‐CMCh microparticles into Polyblends I and II results in a decrease in the structural viscosity index (Δη) in comparison to that of the cellulose solution, and this effect is very obvious for Polyblend I. A cellulose solution's Δη declines with the augmentation of temperature, while the Δη's of both Polyblends I and II show minimum values at about 323 K. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1719–1725, 2003     

基体树脂对长玻璃纤维增强PP力学性能的影响

采用在线混合设备制备了长玻璃纤维(LGF)增强聚丙烯(PP)复合材料(LGF-PP),研究了基体性质及界面相容剂对LGF-PP力学性能的影响。基体树脂熔体流动速率的增加,使最终LGF-PP中的玻璃纤维长度从5.63 mm增至8.56 mm,提高了力学性能。与均聚PP比较,以共聚PP为基体树脂的LGF-PP冲击强度高出约10%,但其他性能略差。界面相容剂有利于增强玻璃纤维与PP的界面结合,拉伸强度和拉伸模量明显增加,但是冲击强度降低了20%～30%。     

不同处理方式对稻瘟病菌丝致畸作用的比较

用清水、链霉菌D–2的复合诱变菌株和农药春雷霉素3种方式对稻瘟病菌丝进行了处理。结果表明,清水处理对稻瘟病菌丝无任何影响,复合诱变菌株对稻瘟病菌丝的致畸作用主要表现在导致菌丝扭曲和膨大,农药处理对菌丝的致畸作用是使菌丝伸长受抑制,导致菌丝呈颗粒状。     

水解-水热体系中同质异构TiO2纳米晶生成机理的分子模拟研究

在实验研究的基础上,采用分子模拟的方法,对在水解-水热体系中TiO2纳米颗粒晶相生成原理进行了系统的模拟计算和建模研究,文章介绍了分子模拟软件Hyperchem的计算方法,建立了钛离子水解过程和能量分布模型,利用模拟计算和模型,直观和定量分析了水解中间产物、水热晶化过程以及最终产物间的关系。研究了pH值对同质异构相成因的影响机理;静电场作用对同质异构相生成的影响。考察了水合络离子的连接方式,指出顶角连接与棱边连接保持到最终产物的结构中。从能量的角度揭示了同质异构TiO2晶型成因。     

Robust passive autofocus system for mobile phone camera applications

A robust autofocus system is a ubiquitous function in today’s mobile phone camera applications. However, due to the power consumption and size requirements, it is difficult for the autofocus function to be implemented into the design of mobile phone cameras. This paper presents a passive autofocus system with low computational complexity. This system uses a novel contrast measurement to determine degree of image sharpness, which can better reflect the information about image discontinuities. In order to gauge the performance of this measurement, a modified peak search strategy is used in the experiments. The experimental results from several typical image sequences validate the effectiveness of the proposed method.     

Anisotropic geodesics for live‐wire mesh segmentation

We present an interactive method for mesh segmentation that is inspired by the classical live‐wire interaction for image segmentation. The core contribution of the work is the definition and computation of wires on surfaces that are likely to lie at segment boundaries. We define wires as geodesics in a new tensor‐based anisotropic metric, which improves upon previous metrics in stability and feature‐awareness. We further introduce a simple but effective mesh embedding approach that allows geodesic paths in an anisotropic path to be computed efficiently using existing algorithms designed for Euclidean geodesics. Our tool is particularly suited for delineating segmentation boundaries that are aligned with features or curvature directions, and we demonstrate its use in creating artist‐guided segmentations.