Absorption spectral properties of Cu2 ions in sodium potassium sulphate

This short note reports the results concerning electron paramagnetic resonance (EPR) and optical absorption spectra of Cu²⁺ ions doped in sodium potassium sulphate both at 300K and 77K.     

Review of the process development aspects of electrochemical dyeing: its impact and commercial applications

This review discusses the recent progress made in both direct and indirect electrochemical dyeing processes and the parameters that control the dyeing process.     

Nanomechanical Characterization of Indium Nano/Microwires

Nanomechanical properties of indium nanowires like structures fabricated on quartz substrate by trench template technique, measured using nanoindentation. The hardness and elastic modulus of wires were measured and compared with the values of indium thin film. Displacement burst observed while indenting the nanowire. ‘Wire-only hardness’ obtained using Korsunsky model from composite hardness. Nanowires have exhibited almost same modulus as indium thin film but considerable changes were observed in hardness value.     

Effect of imbibed moisture on monotonic and low-velocity impact behavior of injection over-molded short/continuous fiber reinforced polypropylene composites

Design of automotive components with over-molded short/continuous fiber reinforced thermoplastic composites necessitates understanding of their behavior under extreme outdoor conditions. The short, quasi-isotropic and over-molded short/continuous glass fiber reinforced polypropylene (PP) composite specimens were prepared as per standard and immersed in water until equilibration to study their relative moisture absorption characteristics and consequent mechanical behavior. As the absorbed moisture mostly occupied the interface between fiber and matrix in laminated composite inserts and moisture absorption of short fiber composite core is insignificant, the moisture absorption of over-molded composites is just above 50% of that of laminated composites. The flexural, interlaminar shear and impact behavior of equilibrated composites is primarily governed by the quantum of imbibed moisture of composite materials. Optical analysis of failed moisture equilibrated over-molded specimens showed a marginal delamination between plies of the inserts without any perceptible damage within the short fiber composite similar to dry as molded specimens.     

Effect of superfine grinding on properties of <Emphasis Type="Italic">Vaccinium bracteatum</Emphasis> Thunb leaves powder

Vaccinium bracteatum Thunb, have been widely used in various traditional medicines and food products. The narrow and uniform particle size distribution in V. bracteatum Thunb leaves (VBTL) can be achieved through a new emerging type of foodstuff processing and superfine grinding. The VBTL powders were subjected to four particle sizes as followed: 300–125, 125–75, 75–40, and <40 μm. The VBTL powders were observed to be with smaller size and bulk density, greater surface area, tapped density and the angle of repose. Water solubility index, water holding capacity and total flavonoid extraction increased slightly with the decrease in particle size. Differential scanning calorimetry showed that the VBTL exhibiting particle size of <40 μm had the lowest peak temperature; whereas, powder with a particle size of 125–300 μm displayed the largest endothermic enthalpy. Our results of the properties of VBTL superfine powder supplied the basis for VBTL in potential industrial applications of foods.     

Optimization of modern machining processes using advanced optimization techniques: a review

Thorough literature review of various modern machining processes is presented in this paper. The main focus is kept on the optimization aspects of various parameters of the modern machining processes and hence only such research works are included in this work in which the use of advanced optimization techniques were involved. The review period considered is from the year 2006 to 2012. Various modern machining processes considered in this work are electric discharge machining, abrasive jet machining, ultrasonic machining, electrochemical machining, laser beam machining, micro-machining, nano-finishing and various hybrid and modified versions of these processes. The review work on such a large scale was not attempted earlier by considering many processes at a time, and hence, this review work may become the ready information at one place and it may be very useful to the subsequent researchers to decide their direction of research.     

Validation and Examination of Existing Water Distribution Network for Continuous Supply of Water Using EPANET

Dire Dawa, the second largest city of Ethiopia, was facing about the distribution system adopted for supplying clean water. It was being observed that an intermittent type of supply with main and secondary distribution pipes. It was observed that, the current water demand has surpassed the present existing supply about 65%. Hence, in order to provide sufficient quantity and good potable water with continuous (24 X 7) water supply for various sectors of study area: Sabiyan region, Dire Dawa, Ethiopia, was selected. Also, Dire Dawa Water Supply & Sewerage Authority has taken a strong decision in order to validate and examine the existing water distribution network for improved water supply. On the other hand, the main important factor which effects the validation is that the age of pipes and other accessories in present existing network were longstanding. Therefore, to avoid the leakage losses and various problems encountered with the present system, a detailed is study is conducted and the analysis is carried out using EPANET tool to design for continuous water supply. After thorough analysis by considering future concerns, it was suggested that, two GLSRs of each with 2.7 Mm³ capacity may be provided in order to meet the future demands. The tanks are provided at required elevation to ensure that the water flows in all pipes of the network efficiently. Based on the output it was observed that the diameter of pipes from the existing system ought to be revised. Additionally, other parameters which effect the network like frictional losses, velocity of flow in the pipes, residual head and pressure at nodes were also examined thoroughly by the use of different tools like WaterGEMS and Auto CAD in addition to EPANET.     

Valorization of fatty acid waste for bioplastics production using Bacillus tequilensis: Integration with dark-fermentative hydrogen production process

Synthesis of bioplastics (polyhydroxyalkanoates (PHA)) using Bacillus tequilensis, a newly isolated strain was investigated under aerobic condition using designed wastewater with synthetic acids (SA) and acidogenic fermented food waste (AFW) collected from biohydrogen (H₂) producing anaerobic bioreactors as substrates. The isolate showed the ability to grow and accumulate PHA in both the substrates, with simultaneous waste remediation. Higher PHA synthesis was observed with SA (59% dry cell weight) compared to AFW (36% dry cell weight) with good substrate removal (SA, 87%; AFW, 59%). The PHA composition showed presence of co-polymer [P(3HB-co-3HV)] with varying contents of hydroxy butyrate (HB, 80–90%) and hydroxy valerate (HV, 10–15%) in both the substrates. High dehydrogenase activity was observed which leads to the formation of considerable quantity of PHA. AFW from H₂ producing reactor as substrate contributes in reducing the production cost of both H₂ as well as PHA embedded with waste valorization.     

Dielectric barrier discharge plasma induced surface modification of polyester/cotton blended fabrics to impart water repellency using HMDSO

Continuous treatment of polyester/cotton blended fabric samples was carried with hexamethyldisiloxane (HMDSO) plasma on the pilot scale atmospheric pressure plasma reactor. The mixture of helium and argon was used as carrier gas for generating dielectric barrier discharge plasma. The effect of discharge power and treatment time on the water repellent properties of samples were evaluated with contact angle (CA) and spray test measurements. Spray test and CA results showed improved resistance to wetting with water. The effect of discharge conditions on the surface morphology and surface chemistry of plasma treated samples were investigated by scanning electron microscopy (SEM) and Fourier transform infrared (FTIR) spectroscopic analysis, respectively. The presence of Si‐O‐Si and Si‐CH₃ groups in the structure of plasma polymer deposited at the surface of P/C samples was revealed by FTIR spectroscopy. Further, structural differences in HMDSO plasma polymer deposited under different discharge conditions were reported with reference to organic/inorganic nature of plasma polymer. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011.     

Control system design for recycle systems

This paper considers the control system design for recycle systems. We derive a condition which quantifies the effect of recycling on closed-loop performance. The condition is independent of control/controller structure. With insight from this condition, we develop a set of heuristics for properly designing a controller without detailed knowledge of recycle dynamics for the important special case where the system is represented by a first-order-plus-time-delay model and where the IMC tuning rules are used. The heuristics require only a minimal amount of information on the recycle dynamics. Their effectiveness is illustrated on a reactor/feed-effluent heat exchanger/furnace process under various conditions.