A Method for Reducing the Dead‐Time Voltage and Impedance Voltage in a Series Voltage Compensator

Many research groups are developing series voltage compensators. In a series converter, since a transformer is used in series in the power system, the power system current flows into the voltage source inverter through the transformer. The inverter current, which is determined by the transformation ratio, gives rise to an error voltage that consists of a dead‐time voltage and an impedance voltage. The error voltage is generated even when the reference voltage is zero. This paper describes the mechanism by which the error voltage occurs and proposes a method for reducing the error voltage. © 2013 Wiley Periodicals, Inc. Electr Eng Jpn, 186(3): 85–93, 2014; Published online in Wiley Online Library ( wileyonlinelibrary.com ). DOI 10.1002/eej.22333     

Impact of Dynamic Interlayer Interactions on Thermal Conductivity of Ca3Co4O9

The phonon thermal conductivity of misfit-layered Ca₃Co₄O₉ has been calculated by perturbed molecular dynamics using a classical force field. Detailed numerical analyses reveal that, in spite of its smaller cross-sectional area, the CoO₂ layer transports more heat than the thicker rock salt (RS) layer, although its local thermal conduction is more suppressed than in another layered cobaltite, Na _x CoO₂. The origins of these differences have been elucidated through careful examination of the atomic arrangements in each layer. Since thermal conduction in the RS layer can be reduced without deteriorating electronic properties for which the CoO₂ layer is responsible, it is suggested that the RS layer should be modified to further suppress the overall in-plane thermal conductivity. Computational experiments with increasing number of Ca–O planes in the RS layer showed the opposite trend to what can be predicted based on the misfit between two dissimilar layers. Further analyses to reveal the origin of these unexpected results provide yet another strategy to further decrease the thermal conductivity, namely to control the dynamic interference between atoms across the interface between two layers.     

Effect of Vacuum Heat Treatment on Electron-Beam-Irradiation-Cured Polycarbosilane Fibers

Electron-beam-cured polycarbosilane fibers were heat-treated at 673–1773 K in a tube evacuated to 1.3 × 10⁻¹ Pa and then exposed at 1873 K in argon. The effect of vacuum heat treatment on improving the high-temperature stability of low-oxygen SiC fibers was investigated by examining gas evolution, grain growth, surface composition, tensile strength, and morphology. The fibers heat-treated at <1173 K lost strength, because of the vigorous generation of residual hydrogen. A minute amount of oxygen in the atmosphere caused the active oxidation of SiC during heat treatment at >1673 K, resulting in severe strength degradation for the as-heat-treated fibers. Vacuum heat treatment at 1573 K provided the best characteristics in low-oxygen SiC fibers.     

Correlations of Hepatic Hemodynamics,Liver Function,and Fibrosis Markers in Nonalcoholic Fatty Liver Disease: Comparison with Chronic Hepatitis Related to Hepatitis C Virus

The progression of chronic liver disease differs by etiology. The aim of this study was to elucidate the difference in disease progression between chronic hepatitis C (CHC) and nonalcoholic fatty liver disease (NAFLD) by means of fibrosis markers, liver function, and hepatic tissue blood flow (TBF). Xenon computed tomography (Xe-CT) was performed in 139 patients with NAFLD and 152 patients with CHC (including liver cirrhosis (LC)). The cutoff values for fibrosis markers were compared between NAFLD and CHC, and correlations between hepatic TBF and liver function tests were examined at each fibrosis stage. The cutoff values for detection of the advanced fibrosis stage were lower in NAFLD than in CHC. Although portal venous TBF (PVTBF) correlated with liver function tests, PVTBF in initial LC caused by nonalcoholic steatohepatitis (NASH-LC) was significantly lower than that in hepatitis C virus (C-LC) (p = 0.014). Conversely, the liver function tests in NASH-LC were higher than those in C-LC (p < 0.05). It is important to recognize the difference between NAFLD and CHC. We concluded that changes in hepatic blood flow occurred during the earliest stage of hepatic fibrosis in patients with NAFLD; therefore, patients with NAFLD need to be followed carefully.     

Challenges Upon Reactive Plasma Spray Nitriding: Al Powders and Fabrication of AlN Coatings as a Case Study

Reactive plasma spraying (RPS) is a promising technology for the in situ formation of several ceramic coatings. The focus of this paper is to summarize the state of our current knowledge about the RPS process and using the nitriding of Al particles and the fabrication of aluminum nitride coatings, as a case study. The aspects and challenges in this process such as the influence of the plasma power, in-flight time, particle size, nitriding mechanism, splat morphology, in-flight particle diagnostics, N₂ plasma gas, and the feeding rate on the RPS process are analyzed and discussed.     

Inhibition of char deposition using a particle bed in heating section of supercritical water gasification

Supercritical water gasification (SCWG) has attracted attention as a technology for utilizing wet biomass. We used a fluidized bed of alumina particles to prevent blockage of a SCWG reactor. A glucose solution was heated in the reactor with and without fluidized alumina particles. In the absence of alumina particles, char particles formed homogeneously in the reactor, but the use of a fluidized bed resulted in accumulation of char particles at the reactor’s exit rather than inside the reactor. Therefore, the fluidized bed was effective at preventing blockage of the reactor. However, the alumina particles did not remove deposits from the reactor’s walls. Instead, the fluidized bed caused larger char particles to form, preventing their adhesion to the reactor’s wall.     

Advantage of Sodium Polyoxyethylene Lauryl Ether Carboxylate as a Mild Cleansing Agent

Five anionic surfactants widely used in commercial skin cleansers were studied: sodium polyoxyethylene lauryl ether carboxylate (EC), sodium polyoxyethylene alkyl ether sulfate (ES), sodium dodecyl sulfate, potassium laurate, and N-cocoyl-l-glutamic acid monosodium salt. The amount of surfactant from aqueous solution adsorbed into the stratum corneum (SC), the degree of SC swelling, the change of the secondary structure of SC proteins (denaturation). The surface tension of surfactant–zein mixed solutions, and the solubilization behavior of zein were measured. Results showed that EC had the lowest adsorption into SC, the lowest SC swelling, and lowest denaturation of SC proteins. Low interactions between surfactants and SC proteins were also observed for EC/ES mixture solutions as well as. Mixing EC with ES good foaming performance. The EC/ES mixture, at about 1:1 ratio, is an excellent surfactant system for skin cleanser applications having cleansing characteristics and mildness to the skin.     

Organic–inorganic nanomatrix structure and properties of related naturally occurring rubbery macromolecules

The outstanding mechanical properties of soft materials i.e. natural rubber are partly due to the organic–inorganic nanomatrix structure because numerous organic microparticles are dispersed in a small amount of an inorganic nanomatrix composed of inorganic nanoparticles and organic macromolecules. Here we form an organic–inorganic nanomatrix using graft-copolymerization of a vinyl monomer with an inorganic oxide precursor onto natural rubber particles with an average diameter of 1 μm dispersed in water. The inorganic oxide precursor is converted into inorganic oxide nanoparticles through hydrolysis and condensation, forming chemical linkages between natural rubber microparticles and inorganic oxide nanoparticles. Transmission electron microscopy indicates that the organic–inorganic nanomatrix is densely filled with inorganic oxide nanoparticles and the natural rubber microparticles are dispersed in the nanomatrix. This nanomatrix composite realizes both energetic elasticity and entropic elasticity of a soft material, opening a novel field of building block chemistry with respect to a pair of organic microparticles and inorganic nanoparticles.     

Boiling heat transfer characteristics of a sulfuric-acid flow in thermochemical iodine–sulfur cycle

The Japan Atomic Energy Agency has been conducting research and development on the thermo-chemical iodine–sulfur (IS) process, which is one of the most attractive water-splitting hydrogen production methods that uses nuclear thermal energy. The sulfuric acid decomposer is one of the key components of the IS process. The boiling heat transfer coefficients of sulfuric acid solutions are required to design the sulfuric acid decomposer. These coefficients were measured in aqueous solutions where the mole fraction of H₂O ranged from 0.17 to 0.37 (heat flux range from 16.9 kW/m² to 5.6 kW/m²) and compared with the empirical correlations formulated for binary mixtures. A combination of the Stephan–Körner correlation, using the empirical constant A₀ = 2.00, and the Nishikawa–Fujita correlation was used to predict the experimental results with an accuracy of ±10%.