水力机械模型试验台的设计研究

扼要介绍在水力机械模型试验台建设中,对试验台的主管路系统、流量率定系统、扭矩测量系统等进行的研究。开发了闸板可抽取式强迫压紧特殊阀,杜绝了管路内漏现象的发生;引进了模型水轮机叶片角度联调机构,在保证叶片角度调整精度的同时又提高了工作效率;采取了保持试验水质清洁的相关措施,节约了宝贵的水资源。该试验台通过了由中国电机工程学会和中国水力发电工程学会组织的技术鉴定,达到国际先进水平。     

The recovery and recrystallization of cold rolled V-W-Ti alloys

Several V-W-Ti alloys with about 50% reduction in thickness by cold rolling were isochronally annealed at temperatures from 100 to 1100 °C. Hardness was measured after the annealing. By comparison with V4Cr4Ti and V4Ti alloys, the V6WTi alloy was found to begin recovery at a temperature about 100 °C higher, while the full recrystallization temperature was around 900 °C for all of the alloys. Hardness decreased successively above 500 °C in V8W, as is the case in pure V. Impurity induced hardening was observed around 300 °C only in the alloys without Ti. Precipitation and the interaction between interstitial impurities and dislocations were supposed to be the main contributors to the different recovery and recrystallization behaviors of the alloys.     

Change of fuel-to-cladding gap width with the burn-up in FBR MOX fuel irradiated to high burn-up

In order to study the dependence of the gap width change on the burn-up, the fuel-to-cladding gap widths were investigated by ceramography in a large number of FBR MOX fuel pins irradiated to high burn-up. The dependence of gap widths on the burn-up was closely connected with the formations of JOG (joint oxyde-gaine) and rim structure. The gap widths decreased gradually due to the fuel swelling until ∼30 GWd/t, but beyond this burn-up the dependence showed two different tendencies. With the increase of burn-up, the gap widths decreased due to the increase of fuel swelling in the low fuel temperature region where the rim structure was observed, but they increased in the high fuel temperature region where the JOG rich in Cs and Mo formed in the gap.     

Feasibility of a 1,400 m Span Steel Cable-Stayed Bridge

This paper describes the feasibility of 1,400 m steel cable-stayed bridges from both structural and economic viewpoints. Because the weight of a steel girder strongly affects the total cost of the bridge, the writers present a procedure to obtain a minimum weight for a girder that ensures safety against static and dynamic instabilities. For static instability, elastoplastic, finite-displacement analysis under in-plane load and elastic, finite-displacement analysis under displacement-dependent wind load are conducted; for dynamic instability, multimodal flutter analysis is carried out. It is shown that static critical wind velocity of lateral torsional buckling governs the dimension of the girder. Finally, the writers briefly compare a cable-stayed bridge with suspension bridge alternatives.     

Stress distribution of coated film with a range of coated film thickness and elastic properties under a single EHL operating condition

In recent years, the techniques improving sliding performances have progressed by using coated films possessing superior tribological properties, to reduce the failures of the mechanical elements. Those techniques are often used under severe conditions such as elastohydrodynamic lubrication (EHL). In this paper, numerical three-dimensional analysis of the maximum shear stress applied into the coated film and substrate under a single EHL operating condition was performed with a range of coated film thickness and elastic properties. The strength of coated film as one of those techniques was evaluated numerically, resulting in an optimum design of coated film. As a result, coated films with a larger value of thickness and a smaller modulus of elasticity than that of substrate are preferable.     

Development of Laser Ionization Techniques for Evaluation of the Effect of Cancer Drugs Using Imaging Mass Spectrometry

Recently, combined therapy using chemotherapy and photodynamic therapy (PDT) has been proposed as a means of improving treatment outcomes. In order to evaluate the efficacy of combined therapy, it is necessary to determine the distribution of the anticancer drug and the photosensitizer. We investigated the use of imaging mass spectrometry (IMS) to simultaneously observe the distributions of an anticancer drug and photosensitizer administered to cancer cells. In particular, we sought to increase the sensitivity of detection of the anticancer drug docetaxel and the photosensitizer protoporphyrin IX (PpIX) by optimizing the ionization-assisting reagents. When we used a matrix consisting of equal weights of a zeolite (NaY5.6) and a conventional organic matrix (6-aza-2-thiothymine) in matrix-assisted laser desorption/ionization, the signal intensity of the sodium-adducted ion of docetaxel (administered at 100 μM) increased about 13-fold. Moreover, we detected docetaxel with the zeolite matrix using the droplet method, and detected PpIX by fluorescence and IMS with α-cyano-4-hydroxycinnamic acid (CHCA) using the spray method.     

Effect of annealing on photovoltaic properties and microstructure of conventional and inverted organic solar cells using active bilayer based on liquid‐crystal semiconducting polymer and fullerene

Conventional and inverted organic solar cells of poly[9,9‐dioctyl‐fluorene‐co‐bithiophene] (F8T2) as liquid‐crystal semiconducting polymer and fullerene as electron acceptor were fabricated and characterized. An effect of thermal treatment of the films on annealing condition near glass transition was investigated for tuning optimization and improving the photovoltaic and optical properties. Annealing treatment below the glass transition improved the photovoltaic performance and carrier diffusion in crystal growth of active layer. The X‐ray diffraction patterns indicate a crystalline structure with molecular order of F8T2 in crystal index, 100 as a layer distance between sheets of F8T2 chains. The photovoltaic properties were based on molecular interactions with molecular ordering in active layer at crystal state. As the photovoltaic mechanisms, the F8T2 thin film as p‐type semiconducting polymer worked for electron‐donor layer to support light‐induced generation, carrier diffusion and charge transfer near interface in active layer. Copyright © 2014 John Wiley & Sons, Ltd.     

Investigation and consideration on landslide zoning of multiple slope failures and debris flows of 2014 disaster in Hiroshima,Japan

This study was intended to examine the mechanism of multiple slope failures and debris flows that occurred in the outskirts of Hiroshima on 20th August 2014. A field survey of the mountain stream where large-scale damage was incurred was carried out and the characteristics of debris flows which made serious damages were investigated. There were five findings of this study. (1) The initiation of debris flows was not limited to thin and planar shallow failures, but also showed V or U shapes, where the eroded sediments seemed to be pushed out by artesian water, and the eroded depth exceeded several meters at many locations. (2) There were areas with high permeability, such as faults, fracture zones, and joints in Mt. Abusan. It is inferred that the constantly present groundwater in these areas became artesian water because of a large amount of rainfall in upstream locations. This quickly destabilized the slopes on a large scale. (3) There were at least three estimated debris flows at the mountain stream above Midorigaoka prefectural apartments in Yagi 3-Chome, where the worst damage occurred. The mountain stream near Abu-no-Sato housing complex also had multiple debris flows. Here, the secondary debris flow changed its flow path because of the presence of sediments from an earlier debris flow. (4) The actual volumes of flowed mass were much larger than that predicted at 11 of the 18 mountain streams in Midori-i and Yagi districts. The volume of the mass of five of these mountain streams was more than twice the estimated volume. It is necessary to modify the method of calculating the volume of unstable sediments in the mountain stream. (5) It was found that the devastating damage of buildings and human lives took place in the areas well beyond the special restricted zones. The present method to designate the special restricted zone must be revised considering such problems as the underestimation of the volume of unstable sediments, the assumptions of a single debris flow and on the direction of debris flow, and the effect of the difference on rock and soil types.     

LiErO2 formation on Er2O3 in static and natural convection lithium

Er₂O₃ is candidate material for insulating coating to prevent the magnetohydrodynamic (MHD) pressure drop in the self-cooled liquid Li blanket system. Although Er₂O₃ is stable material, detailed chemical behavior in liquid Li is not clear. Corrosion behavior of bulk Er₂O₃ in Li is investigated in static and flowing condition in the present study. After these tests, good compatibility of Er₂O₃ was confirmed and slight formation of LiErO₂ was detected by XRD analysis. This chemical behavior did not change in a static and flowing tests, however some of the corrosion product of LiErO₂ was removed easily by the Li flow. Intensity of LiErO₂ peaks in XRD spectrum suggests that the temperature gradient may affect the reaction rate in the natural convection loop. Since corrosion rate of Er₂O₃ is very small, slight change in state will be important information to evaluate lifetime of coating.