EWB应用于模拟电路分析的研究

介绍了将EWB用于“模拟电子技术”的课堂教学时，虚拟实验测量结果与理论计算值不一致时，如何去分析并解决问题。     

DNA/lipid complex organogel with shape‐memory behavior

DNA and amphiphilic N,N,N‐trimethyl‐N‐hexadecylammonium bromide (THAB) were stoichiometrically mixed together to produce a DNA–lipid complex, which was dissolved in dimethyl sulfoxide (DMSO) at 65°C and then crosslinked with isophorone diisocyanate (IPDI). The obtained organogel swelled reversibly in DMSO, responding to the variation of temperature. Interestingly, we observed that the gel exhibited a temperature‐dependent shape‐memory behavior. Above 65°C, whatever the shape the gel was deformed to, it could retain the new shape as the temperature was decreased to room temperature, while, when the gel was heated to 65°C again, it could recover its initial shape. The shape‐memory characteristic is supposedly originated from the transition between the close‐packed and the destroyed DNA/lipid conformation. The elastic urethane crosslinking bonds between base‐pair sites act as a fixing phase. The gel holds promise in its application as a gentle actuator. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 259–263, 2002     

基于数字图像分析的薄板成形应变场测量方法

对薄板成形应变场传统的测量方法进行了研究。指出了其不足和误差的来源，提出了数字图像分析法测量薄板成形中的应变场，对测量原理，新的测量方法对传统方法的改进，以及如何降低误差进行了介绍，指出数字图像分析法的前景，提出了改进意见。     

频率伪随机捷变引信信号分析

根据频率捷变技术在无线电引信中的应用特点，分析了无线电引信发射频率伪随机捷变引信的信号特征，研究了其模糊函数和信号所携带的目标信息，指出提高无线电引信系统性能的技术途径，为频率捷变引信各种技术方案提供指导。     

石英玻璃基复合材料的研究进展

石英玻璃基复合材料属于重要国防材料，在导弹通讯、制导和防热上具有不可取代的地位。本工作介绍了几种形式的石英玻璃基复合材料的组织结构、性能和制备工艺的研究与应用情况。同时提出了石英玻璃基复合材料研究中存在的问题。     

方波扫描路径确定声源声功率误差特性分析

改进了矩形测量面方波扫描路径测量声功率的误差模型 ,以单极子、偶极子及四极子声源为例 ,给出了扫描方向、测量面离声源的距离及扫描线的密度的选取对理论误差的分布图形。分析结果表明 :对选定的测量面 ,在扫描线密度小的情况下 ,通过调整声源离测量面的距离 ,可以在声源近处找到一个最优点或较优点 ,使理论误差为零或很小 ;在绝大多数情况下 ,沿测量面长边扫描误差比沿短边扫描小。     

地域通信网的干扰技术研究

本文在分析地域通信网结构及组成的基础上,研究了对地域通信网实施的节点破坏、末端信息封锁、局部阻塞瘫痪等对抗方法,并使用干扰地域通信网的程度、节点干扰率、末端节点封锁率和传递信息误差率等指标对干扰效果进行评估。     

高非线性光纤及其应用

介绍了各种高非线性光纤的原理，并对其在超连续（SC）脉冲的产生和波长变换上的应用作了讨论。     

苯胺衍生物改性酚醛树脂的性能和结构表征

选用某种叔胺类化合物作苯酚和甲醛反应的催化剂,并加入少量苯胺衍生物,制备了一种分子量较高的改性酚醛树脂。根据IR、NMR和GPC的测试分析,对苯胺衍生物改性酚醛树脂的结构特征等进行了研究。它与环氧树脂合成压制的玻璃布层压板的浸水后绝缘电阻可达1011Ω以上,其它主要性能也达到了国外同类产品水平。     

Effect of partitioning on microstructure and properties of a medium carbon Ti Mo bearing high strength Q&P steel

In order to investigate the effect of partitioning procedures on microstructure and properties of a medium carbon Ti Mo bearing steel, the salt bath experiment, field emission SEM, TEM and tensile tests as well as wear tests were utilized to clarify the microstructural evolution and property changes treated by different partitioning parameters. The results show that the microstructures consist of tempered lath martensite, cementite and (Ti, Mo)C particles. With prolonging partitioning time or increasing partitioning temperature, the amount of laths martensite decreases and thicker martensite plates with blunt boundaries appear. In addition, with increasing partitioning temperature from 310℃ to 400℃, the tensile strength, hardness and low temperature toughness are simultaneously decreased, and the reduction reaches up to about 300MPa, 100HV and 20J, respectively. Finally, the wear performance of the samples partitioned below Ms is obviously better than that of samples partitioned above Ms. The morphology of worn surface of samples partitioned below Ms is characterized by plastic fatigue morphology, while the worn surfaces of samples partitioned above Ms are mainly dominated by grooves.