Adaptive Finite-time Tracking Control for Class of Uncertain Nonlinearly Parameterized Systems with Input Delay

International Journal of Control, Automation and Systems - In this paper, the tracking problem for a class of uncertain nonlinearly parameterized systems with input delay based the adaptive...     

Alloy optimisation of bainitic steel for large plastic mould

Based on the phase transformation theories, especially the T₀ concept of bainite transformation, alloy optimisation of bainitic steel with carbides has been carried out aiming at the produce of plastic mould with large cross-section. The effect of manganese and silicon on proeutectoid ferrite and bainite transformation is explored by dilatometric analysis, XRD and different microscopy techniques. The results show that after the alloy optimisation, the transformation of proeutectoid ferrite is suppressed and when the cooling rate is lower than 0·1°C?s^??1, the new lower bainite transformation appears by decreasing carbon capacity of austenite and promoting carbide precipitation. Industrial production proves that the optimised alloy SDP1 can meet the demand for the plastic mould with the thickness of 1050?mm.     

某含锌锡多金属硫化矿石锌浮选试验研究

某含锌锡多金属硫化矿石Zn、Sn、Fe、S含量分别为6.04%、1.05%、29.33%、19.08%，锌主要以铁闪锌矿、闪锌矿的形式存在，锡主要以锡石的形式存在，铁主要以黄铁矿、磁黄铁矿等形式存在，其中的金属矿物共生关系密切，相互包裹现象普遍。为确保不影响后续选锡，对锌浮选流程进行了试验研究。结果表明：矿石在磨矿细度为-0.074 mm占80%的情况下，采用预先脱硫—锌硫混浮再分离流程处理，在选择硫酸铜为锌矿物活化剂、丁基黄药为捕收剂、松醇油为起泡剂、石灰为黄铁矿抑制剂的情况下，经1段脱硫、2粗1扫锌硫混浮、1粗2精锌硫分离，锌硫分离精选尾矿与锌硫混浮扫选精矿2次精选后锌硫分离，最终获得锌精矿Zn品位47.06%、回收率90.76%，试验指标良好。     

山东栖霞—大柳行地区金矿找矿靶区地质评价及优选

栖霞—大柳行地区位于胶东中部栖霞—蓬莱金矿成矿带内，是胶东重要的金成矿区，成矿条件优越。为了对圈定靶区进行优选分类，通过对该区地质背景、找矿靶区评价、找矿靶区优选方面展开综合研究，并结合勘查工作程度和矿业权设置情况，划分出3类预测区，选定了5个靶区为今后优先部署勘查工作的方向。     

Effects of Cooling Rate and Component on the Microstructure and Mechanical Properties of Mg–Zn–Y Alloys

The microstructure and mechanical properties of Mg–6Zn–1Y and Mg–6Zn–3Y(wt%) alloys under different cooling rates were investigated. The results show that the second dendrite arm spacing(SDAS) of Mg–6Zn–1Y and Mg–6Zn–3Y is reduced by 32 and 30% with increasing cooling rates(Rc) from 10.2 to 23 K/s, which can be predicted using a empirical model of SDAS=68 R 0:45:45cand SDAS=73 R 0c, respectively. The compressive strength of both alloys increases with increasing the cooling rate, which is attributed to the increase of volume fraction(Vf) of secondary phases under high cooling rate. The interaction of the cooling rate and component with SDAS has been theoretically analyzed using interdependence theory.     

Influence of Si-Doping on the Performance of InGaN/GaN Multiple Quantum Well Solar Cells

Semiconductors - The performance of InGaN/GaN multiple quantum well (MQW) solar cells with five different Si-doping concentrations, namely 0, 4 × 1017 cm–3, 1 × 1018 cm–3, 3...     

Single copper sites dispersed on hierarchically porous carbon for improving oxygen reduction reaction towards zinc-air battery

The demand for high-performance non-precious-metal electrocatalysts to replace the noble metal-based catalysts for oxygen reduction reaction(ORR)is intensively increasing.Herein,single-atomic copper sites supported on N-doped three-dimensional hierarchically porous carbon catalyst(Cu₁/NC)was prepared by coordination pyrolysis strategy.Remarkably,the Cu₁/NC-900 catalyst not only exhibits excellent ORR performance with a half-wave potential of 0.894 V(vs.RHE)in alkaline media,outperforming those of commercial Pt/C(0.851 V)and Cu nanoparticles anchored on N-doped porous carbon(CuNPs/NC-900),but also demonstrates high stability and methanol tolerance.Moreover,the Cu₁/NC-900 based Zn-air battery exhibits higher power density,rechargeability and cyclic stability than the one based on Pt/C.Both experimental and theoretical investigations demonstrated that the excellent performance of the as-obtained Cu₁/NC-900 could be attributed to the synergistic effect between copper coordinated by three N atoms active sites and the neighbouring carbon defect,resulting in elevated Cu d-band centers of Cu atoms and facilitating intermediate desorption for ORR process.This study may lead towards the development of highly efficient non-noble metal catalysts for applications in electrochemical energy conversion.