X-ray microfluorescence analysis of pigments in decorative paintings from the sarcophagus cartonnage of an Egyptian mummy

This work characterized the elemental composition of the pigments used in decorative paintings from the sarcophagus cartonnage fragments of an Egyptian mummy, using μXRF with Synchrotron Radiation. This female mummy (n.158) is considered one of the most important pieces of the National Museum (Rio de Janeiro, Brazil) because of its unconventional embalming with legs and arms swathed separately. The measurements were performed at the XRF beamline D09B of the Brazilian Synchrotron Light Laboratory (LNLS), using white beam and a Si(Li) detector with resolution of 165 eV at 5.9 keV. The elements found in the samples were: Si, S, Cl, K, Ca, Ti, Cr, Mn, Fe, Ni, Cu, Zn, As, Sr, Hg and Pb.     

Impact of the addition of an enzyme pool on an activated sludge system treating dairy wastewater under fat shock loads

BACKGROUND: The application of lipase‐rich enzyme pools (such as the crude solid enzymatic preparation (SEP) obtained from Penicillium restrictum solid‐state fermentation of agro‐industrial wastes) to activated sludge systems may be an effective strategy for preventing various operational problems. The continuous addition of SEP to the treatment system can become cost‐prohibitive when in situ production and/or storage are factored in. The application of SEP to high‐fat wastewater treatment would only be justified as an emergency measure, such as a sudden increase in the fat content of the bioreactor influent. Therefore, the primary objective of this work was to investigate the efficiency of a crude SEP during fat shock loads, simulated through the periodic addition of dairy industry waste containing high fat concentrations to the feed stock of an activated sludge system, operated in continuous mode. RESULTS: The test bioreactor exhibited a higher average chemical oxygen demand (COD) removal efficiency than the control bioreactor (83% for control and 90% for test) and the fat accumulation in the biological flocs of the test bioreactor was 3.2 times lower than that in the control bioreactor. Turbidity was also lower in the effluent of the test bioreactor (123 and 66 FTU in control and test, respectively) and it had a shorter recovery time between shock loads, especially when the interval between loads was shorter than one month (biweekly and weekly shock loads). CONCLUSION: The addition of SEP during fat overloads in the reactor feed maintained efficient COD removal in the test bioreactor for 270 days without any operational problems. Copyright © 2008 Society of Chemical Industry     

Increasing the Complexity of Magnetic Core/Shell Structured Nanocomposites for Biological Applications

This Review article ponders core/shell structured nanoparticles that can be prepared with features that combine properties of different materials, including ligands that enhance their biocompatibility. These nanocomposites are not classified in terms of synthesis, but rather by how these features are distributed in the final morphology, attending to connected or isolated materials that end up in interacting or not‐interacting functionalities. In particular, we have focused on magnetic core/shell‐structured particles with a directly connected, coupled, or isolated second functionality. The current progress on methods in colloidal solution that have allowed the great development of these multifunctional magnetic and active spheres on biological and biomedical fields is reported.     

Multi-level simulation of metal-forming processes

The IBF has for some years made use of finite element programmes to solve metal-forming problems. In the course of this investigation, it has become evident that a problem-oriented adaptation of FEM simulation to the problem in hand is beneficial in terms of computation effort. The computation time for the process parameters is optimised in a multi-level simulation. At level 1 (global analysis) integral parameters such as the required force and required work are computed using a coarse FEM mesh. At level 2 (local analysis) an optimised number of elements is used to determine continuum mechanics parameters like stress, strain and temperature. Microscopic phenomena are simulated at level 3 (microscopic analysis), using special micro-material elements and thermodynamic models.     

Constructing candidate word lists using acoustically similar wordgroups

A method for identifying a set of candidate words that matches well with a given utterance is discussed. The method uses precomputed groups of acoustically similar words. Given a vocabulary, for each word a short list of words that are acoustically similar to it is computed. These groups are constructed using training utterances recorded by several speakers and used in an isolated utterance recognition system to construct candidate word lists during recognition. Experiments show that the correct word appears on the short list of candidate words constructed during recognition using this scheme over 98% of the time     

Transient dynamics of cylinders under wave slamming

Large diameter slender cylindrical shells used as buoyancy chambers and support legs for compliant marine structures experience a variety of impact loadings which could induce significant levels of dynamic response. By examining the response of a typical range of cylindrical shell geometries to a simulation of the impact loading typical of wave slamming, the paper examines the likely levels and practical significance of the transient dynamic response. It shows that the levels of dynamic response are sufficiently severe to have important implications for the triggering of buckling and fatigue collapse characteristics. It is suggested that this phenomenon requires additional more-detailed consideration, including the provision of reliable predictions of transient slam pressure distributions and the levels and forms of hydrodynamic damping, as well as the effects of more practical shell and stiffening geometries, and ambient stress levels.     

Mesh‐independent p‐orthotropic enrichment using the generalized finite element method

This paper is aimed at presenting a simple yet effective procedure to implement a mesh‐independent p‐orthotropic enrichment in the generalized finite element method. The procedure is based on the observation that shape functions used in the GFEM can be constructed from polynomials defined in any co‐ordinate system regardless of the underlying mesh or type of element used. Numerical examples where the solution possesses boundary or internal layers are solved on coarse tetrahedral meshes with isotropic and the proposed p‐orthotropic enrichment. Copyright © 2002 John Wiley & Sons, Ltd.     

Propagation of flicker in electric power networks due to windenergy conversions systems

Wind energy conversion systems (WECS) produce fluctuating output power, which may cause voltage fluctuations and flicker. Flicker assessment in networks may be difficult since its evaluation requires long computing time and special procedures to calculate the flicker severity index, Pst. In this paper, a frequency domain method to study flicker propagation is presented. This method is based on propagation of frequency components from WECS output currents throughout the grid. In this way, a fast flicker analysis in a network of any size can be performed. Also, an algorithm for flicker measurement in the frequency domain, which allows Pst calculation, is proposed. Several study cases have been performed, and results have been compared with time domain simulations, showing good agreement between them     

Chromosome comparison between populations of the collared peccary, Tayassu tajacu, raised in captivity

The collared peccary (Tayassu tajacu) is widely distributed over the American continent, being found from the south of the USA to the north of Argentina. In Brazil, it is spread all over the country, being one of the potential species to be raised in captivity. Therefore, the cytogenetic techniques could be a potential tool for reproductive monitoring of animals raised in captivity, mainly when destined for commercial purposes. This study had the objective of determining the chromosome number of two populations raised in captivity and characterizing them by GTG banding. For this purpose, an analysis was made of mitotic metaphases obtained from lymphocyte cultures made from blood samples of 11 animals, six of which from the Northeast and five from the North of Brazil. The results of this analysis showed the same karyotype pattern for the species (2n=30 chromosomes and NF=48), besides corresponding to the South American pattern of the species, i.e., without a translocation between autosomes 1 and 8, chromosome X acrocentric, and no differences were found between the two populations studied. However, chromosomal polymorphisms were observed compared to data from the literature on populations from North and South America.