Fabrication of octacalcium phosphate block through a dissolution-precipitation reaction using a calcium sulphate hemihydrate block as a precursor

Although octacalcium phosphate (OCP) powder and a collagen/gelatin composite demonstrate good potential as bone substitutes, an OCP block has not been fabricated to date. In this study, the feasibility of fabricating an OCP block was evaluated through a dissolution-precipitation reaction using a calcium sulfate hemihydrate (CSH) block as a precursor. When the block was immersed in a phosphate salt solution, its composition changed to that of OCP, while its structure was maintained. The diametral tensile strength (DTS) of the OCP block was 1.0?±?0.2?MPa. The macroporosity and microporosity of the OCP block were 33.4?±?4.5% and, 69.0?±?1.6%, respectively. New bone attached well to the OCP block, and this block was partially replaced by bone 2 weeks after implantation. Four weeks after implantation, the surface of the OCP block was nearly covered with new bone and ~30% of the block was replaced by new bone, while no replacement by bone was observed in the case of a hydroxyapatite (HAp) block used as a control. It is concluded that OCP blocks are potentially suitable for their use as artificial bone substitutes.     

Performance Comparison of Circuits for Pole‐Mounted STATCOM Using SiC Devices

The recent years have seen an increasing trend in the cumulative installed capacity of distributed generators. As a result, voltage management may become difficult in existing power distribution systems in the future. A STATCOM (STAtic synchronous COMpensator) is a promising option for solving this problem because it can control reactive power rapidly and continuously. For a distribution system, STATCOM needs to be pole‐mounted to realize its low cost. However, a transformer for a STATCOM is large and heavy, and hence it is difficult to install a STATCOM on a distribution pole. We adopt a transformerless STATCOM to reduce STATCOM size and use SiC devices with low‐loss performance to obtain a more compact and efficient STATCOM. There are a large number of circuits available for a STATCOM, and there has been considerable research on performance comparisons among these circuits. However, these comparisons were drawn under different conditions, including switching frequency and level number for the circuits. In addition, these comparisons do not include the use of SiC devices. We made an equitable comparison for a 100 kVa pole‐mounted STATCOM using SiC devices. We discuss the performance and characteristics of each circuit in terms of efficiency and volume.     

Study of Cuprate Superconductivity Using the Particle Number Conserving Bogoliubov-de Gennes Equations: ARPES and STS Images From Surface Plus Bulk Layers Model

Journal of Superconductivity and Novel Magnetism - We theoretically study the superconductivity in hole-doped cuprate superconductors by employing a model composed of surface and bulk CuO $$_2$$...     

Possibility of Japanese Cedar Pollen Causing False Positives in the Deep Mycosis Test

Because Japanese cedar pollen (JCP) contains beta-1,3-d-glucan (BG), there is concern that its lingering presence in the atmosphere, especially during its scattering period, may cause false positives in the factor-G-based Limulus amebocyte lysate (LAL) assay used to test for deep mycosis (i.e., G-test). Hence, we examined whether the LAL assay would react positively with substances contained in JCP by using the G-test to measure JCP particles and extracts. BG was purified from the JCP extract on a BG-specific affinity column, and the percentage extractability was measured using three different BG-specific quantitative methods. The G-test detected 0.4 pg BG in a single JCP particle and 10 fg from a single particle in the extract. The percentage extractability of JCP-derived BG was not significantly different among the three quantitative methods. As the JCP particles should technically have been removed during serum separation, they should be less likely to be a direct false-positive factor. However, given that the LAL-assay-positive substances in the JCP extract were not distinguishable by the three BG-specific quantitative methods, we conclude that they may cause the background to rise. Therefore, in Japan false positives arising from JCP contamination should be considered when testing patients for deep mycosis.     

Measurement of Flow Stress in Supercooled Austenite for High Hardenability Steel

In this article, the isothermal flow stress in supercooled austenite was measured for a high hardenability steel. Supercooled austenite forms at the nonequilibrium phase and changes into other phases within a short time. It was confirmed that conventional tensile tests, which require maintaining a constant temperature before stretching, cannot accurately measure the flow stress in supercooled austenite. Therefore, a new tensile test named “the continuous cooling tensile test” was developed. In this test, stretching is conducted during continuous cooling. In the continuous cooling tensile test, the flow stress between 673 K and 973 K (400 °C and 700 °C) was measured. Microscopic observations of the continuous cooling test results verified that the microstructures were supercooled austenite.     

Influence of Cu metal on the domain structure and carrier mobility in single-layer graphene

We demonstrate that domain structure of single-layer graphene grown by ambient pressure chemical vapor deposition is strongly dependent on the crystallinity of the Cu catalyst. Low energy electron microscopy analysis reveals that graphene grown using a Cu foil gives small and mis-oriented graphene domains with a number of domain boundaries. On the other hand, no apparent domain boundaries are observed in graphene grown over a heteroepitaxial Cu(111) film deposited on sapphire due to unified orientation of graphene hexagons. The difference in the domain structures is correlated with the difference in the crystal plane and grain structure of the Cu metal. The graphene film grown on the heteroepitaxial Cu film exhibits much higher carrier mobility than that grown on the Cu foil.     

Effect of silicon and heat-treatment temperature on the morphology and mechanical properties of silicon - substituted hydroxyapatite

The precipitation method was used to synthesize silicon-substituted hydroxyapatite with different Si contents of 0.4, 0.8 and 1.6 wt.% (0.4, 0.8 and 1.6Si-HA) using silicon acetate [Si(OCOCH₃)₄] as a Si source. As-synthesized hydroxyapatite (HA) and Si-HA powders/bulks were heat-treated at different temperatures of 1150, 1200 and 1250 °C for 1 h. Pure 0.4Si-HA and 1.6Si-HA were obtained after heat-treatment at all temperatures, whilst α-TCP phase was formed in the 0.8Si-HA sample after heat-treatment at 1250 °C. SEM observation clearly showed that the substitution of Si in HA inhibited the grain growth of Si-HA even at high heat-treatment temperatures (1200 or 1250 °C). The highest diametral tensile strength (DTS) of 15.93 MPa was obtained in the 1.6Si-HA sample after heat-treatment at 1250 °C.     

Boroxine Nanotubes: Moisture‐Sensitive Morphological Transformation and Guest Release

Boroxines, (R‐BO)₃, which can be easily synthesized via a dehydration reaction of boronic acids, R–B(OH)₂, selectively self‐assemble in toluene into nanofibers, nanorods, nanotapes, and nanotubes, depending on the aromatic substituent (R). Spectroscopic measurements show that the nanotube consists of a J‐aggregate of the boroxine. Humidification converts the morphology from the nanotube to a sheet as a result of the hydrolysis of the boroxine components and subsequent molecular‐packing rearrangement from the J‐aggregate to an H‐aggregate. Such a transformation leads to the compulsive release of guest molecules encapsulated in the hollow cylinder of the nanotube. The hydrolysis and the molecular‐packing rearrangement described above are suppressed by coordination of pyridine to the boron atom, with the resulting moiety acting as a Lewis acid of the boroxine component. The pyridine‐coordinated nanotube is transformed into a helical coil by humidification. Guest release during the nanotube‐to‐helical‐coil transformation is much slower than during the nanotube‐to‐sheet transformation, but faster than from a nanotube that did not undergo morphological transformation. The storage and release of guest molecules from the boroxine nanotubes can be precisely controlled by adjusting the moisture level and the concentration of Lewis bases, such as amines.