Numerical simulation on void bubble dynamics using moving particle semi-implicit method

In present study, the collapse of void bubble in liquid has been simulated using moving particle semi-implicit (MPS) code. The liquid is described using moving particles and the bubble–liquid interface was set to be vacuum pressure boundary without interfacial heat mass transfer. The topological shape of bubble can be traced according to the motion and location of interfacial particles. The time dependent bubble diameter, interfacial velocity and bubble collapse time were obtained under wide parametric range. The comparison with Rayleigh and Zababakhin's prediction showed a good agreement which validates the applicability and accuracy on MPS method in solving present momentum problems. The potential void induced water hammer pressure pulse was also evaluated which is instructive for further material erosion study. The bubble collapse with non-condensable gas has been further simulated and the rebound phenomenon was successfully captured which is similar with vapor-filled cavitation phenomenon. The present study exhibits some fundamental characteristics of void bubble hydrodynamics and it is also expected to be instructive for further applications of MPS method to complicated bubble dynamics problems.     

c-axis oriented ZnO formed in a rotating magnetic field with various rotation speeds

A rotating magnetic field was used to fabricate c-axis oriented zinc oxide. The influence of rotating speed on orientation structure was also examined. The aligned axes had the largest diamagnetic susceptibility, which axis was difficult to align with a static magnetic field. In c-axis oriented ZnO, the degree of orientation (Lotgering factor) in the green compact ranged from 0.2 to 0.5 along c-axis. The Lotgering factor increased with rotating speed. For all samples with the rotating magnetic field, the degrees of orientation increased up to above 0.9 after sintering at 1573 K.     

Synthesis and optical properties of azobenzene side chain polymers derived from the bifunctional fumaric acid and itaconic acid

Three type polymers containing the same azobenzene side chain group with different backbone structures, poly(DMAz6Fm), poly(DMAz6It) and poly(MAz6Ac) derived respectively from fumaric acid, itaconic acid and acrylic acid, were synthesized. The dependence of photo-response properties on the polymeric architecture was investigated for the solutions and films. By irradiation of the linearly polarized light (436 nm), uniaxial orientations of the thin films were induced and anisotropic properties were investigated by measurements of the order parameters and birefringence values.     

A Study on the Effect of Air on the Dynamic Motion of a MEMS Device and Its Shape Optimization

The authors propose a new design concept for controlling the deflection of a micro-membrane with the aid of its thickness distribution for realizing a prescribed design in the MEMS. As an example, the authors treat a micro air pump that comprises a micro-membrane. The membrane is actuated by an electrostatic force. The membrane deflects and thus the deflection is influenced by the air pressure and the electrostatic field. This is a highly complicated system. To find out a proper thickness distribution, the authors use the genetic algorithm that is appropriate to reduce the searching space of solution.     

Electrochemical analysis of perpendicular mesoporous Pt electrode filled with pure water for clarifying the active region in fuel cell catalyst layers

A perpendicular mesoporous platinum film is used as a model electrode to clarify the effectiveness of catalysts inside agglomerates of fuel cell catalyst layers on the basis of experimental facts. The analysis clarifies that: (i) Pt surface even apart from Nafion ionomer phase can be electrochemically active; (ii) its response is different from that of the surface covered with ionomer; and (iii) ionic resistance in pores filled with pure water is too high (ca. 0.18 MΩ cm) for fuel cell reactions to smoothly occur. We conclude that such catalysts in pores filled with pure water are ineffective for fuel cell reactions due to the high ionic resistance, though their catalytic activity is possibly higher than that of the catalysts covered with Nafion.     

Sweep‐out flow of film condensation on vertical plates with horizontal grooves

We have investigated fluid flow characteristics of film‐wise condensation on vertical plates with horizontal periodic grooves. Condensate stays at the edge of the grooves due to the surface tension. The condensate starts to flow, however, when the balance between the surface tension and the condensate's own weight is broken. It is found that the condensate flows downward successively and periodically from the top part of the plate as a group. In addition, we have obtained the relation between the frequencies of the periodic flow and the degree of sub‐cooling for two different pitches of the grooves. © 2009 Wiley Periodicals, Inc. Heat Trans Asian Res; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.20249     

Effect of substituting elements on hydrogen uptake for Pd–Rh–H and Pd–Ag–H systems evaluated by magnetic susceptibility measurement

The magnetic susceptibility and the pressure-composition isotherm were measured simultaneously for Pd–Rh–H and Pd–Ag–H systems in order to clarify the effect of Rh or Ag substitution on the hydrogen uptake from viewpoint of the electronic band structure. The magnetic susceptibility of all Pd binary alloys prepared decreased monotonically with increasing hydrogen content. At high hydrogen contents, the magnetic susceptibility became approximately zero for Pd–Rh–H and Pd–Ag–H system, and the hydrogen content at which the magnetic susceptibility gives zero corresponded with the terminal of the plateau region in the isotherm curve. The results indicated that the magnetic susceptibility of hydride phase was almost zero for all Pd binary alloys. On the basis of the band structure of Pd metal, we concluded that atom substitution only affected shift of the energy at Fermi level, and the amount of the hydrogen uptake was dominated by the number of unoccupied d-band in the alloys.     

各种引气剂以及抑泡剂对混凝土经时变化状态等的影响

众所周知,采用粉煤灰制备混凝土,因粉煤灰成分中含有未燃炭等微粒子,容易造成阴离子型引气剂吸附在这些微粒子上,导致含气量经时损失.同时在混凝土的制备、运输过程中,因受采用的材料、拌和状态等物理因素影响,还会发生含气量经时增加的现象.所以在制备、管理混凝土时,如何保证出机初期一定的含气量、缓解含气量的经时损失或经时增加,是一项极其关键的技术.本文将就采用能改善上述状态的引气剂、抑泡剂拌和混凝土,对混凝土的经时变化以及抗冻融性等特征产生的影响进行论述.     

In vitro formation and thermal transition of novel hybrid fibrils from type I fish scale collagen and type I porcine collagen

Novel type I collagen hybrid fibrils were fabricated by neutralizing a mixture of type I fish scale collagen solution and type I porcine collagen solution with a phosphate buffer saline at 28 °C. Their structure was discussed in terms of the volume ratio of fish/porcine collagen solution. Scanning electron and atomic force micrographs showed that the diameter of collagen fibrils derived from the collagen mixture was larger than those derived from each collagen, and all resultant fibrils exhibited a typical D-periodic unit of ∼67 nm, irrespective of volume ratio of both collagens. Differential scanning calorimetry revealed only one endothermic peak for the fibrils derived from collagen mixture or from each collagen solution, indicating that the resultant collagen fibrils were hybrids of type I fish scale collagen and type I porcine collagen.