Effects of ozonized water and heat treatment on the papaya fruit epidermis

This study examined the effects of O₃ and hot water treatments on the epidermis of Golden papaya fruit. Heat treatments were applied in a hot water brushing (HWB) system. Papayas were brushed under a pressurized hot water rinse stage at 45, 55 and 65 °C for 60 s. In the HWB treatment, 4 ppm ozone was applied to the papayas for 1 or 2 min. The results show that ozone applications did not affect the fruit's cuticular surface, while heat treatments allowed natural fissures on the fruit epidermis to recover. Several crystalloid forms were identified on the epidermis of the papayas after the heat treatments. The predominant crystalloid forms on papayas are tubular and there is a positive response to temperature; the higher the temperature, the larger and more frequent the tubular crystalloids.     

Influence of ring-type internals on the solids residence time distribution in the fuel reactor of a dual circulating fluidized bed system for chemical looping combustion

The intensification of gas-solids contact in the fuel reactor of a chemical looping combustion system is enhanced with the installation of ring-type internals. This can be a key issue for achieving the necessary fuel conversion rates. Wedged rings, previously designed and tested, were found to increase the particle concentration in the counter current section of the fuel reactor and hence, to achieve a more homogeneous particles concentration along this zone. The present work investigates the effect of the mentioned internals on the residence time distribution of particles in the fuel reactor of a dual circulating fluidized bed system for chemical looping. The study was carried out in a cold flow model especially designed for the fluid-dynamic analysis of the system equipped with a recently developed residence time measurement device based on the detection of ferromagnetic tracer particles through inductance measurement. Ring internals proved the positive effect on the particles residence time, the residence time distribution is more symmetric and shows lower dispersion, the flow pattern is more plug-flow-like, these effects are intensified with the reduction of the aperture ratio of the rings. On the other hand, the upward particle transport in the counter-current zone of the fuel reactor also increases with the installation of the rings, increasing the bypass flow of solids through the fuel reactor's return loop (internal circulation). For high internal circulation rates the solids residence time distribution of the fuel reactor is dominated by the bypass effect. The findings may be used for focused design improvement of the investigated fluidized bed system.     

The transaction costs theory in international business research: a bibliometric study over three decades

Transaction costs theory (TCT) has long been an important conceptual lens for examining International Business (IB) phenomena and perhaps especially relevant for the study of multinational corporations, entry mode choices and location selection. In this paper we examine the extent to which TCT been used and has impacted IB research. Methodologically, we conduct a bibliometric study of the articles published on nine top journals for publishing IB-related research. We use Jean-François Hennart’s research as the key marker for TCT in IB research given that Hennart’s work has been a hallmark in the discipline. On a sample of 377 articles published between 1982 and 2010, and using the works rather than the authors as the unit of analysis, we analyze citations, co-citations and a spatial visualization of the intellectual research themes delved into. Our analyses provide insights on the influence of Hennart but more broadly of TCT on IB research over the past three decades. We conclude that the TCT has a pervasive influence on a large array of IB research and that Hennart’s work is boundary-spanning, connecting several research themes.     

Usability evaluation methods for mobile serious games applied to health: a systematic review

Universal Access in the Information Society - This paper aims to present the results of a systematic review focused on usability evaluation methods for serious games (SG) of mobile devices...     

Synthetic Modular Antibody Construction by Using the SpyTag/SpyCatcher Protein-Ligase System

Efforts to engineer recombinant antibodies for specific diagnostic and therapy applications are time consuming and expensive, as each new recombinant antibody needs to be optimized for expression, stability, bio-distribution, and pharmacokinetics. We have developed a new way to construct recombinant antibody-like “devices” by using a bottom-up approach to build them from well-behaved discrete recombinant antibody domains or “parts”. Studies on antibody structure and function have identified antibody constant and variable domains with specific functions that can be expressed in isolation. We used the SpyTag/SpyCatcher protein ligase to join these parts together, thereby creating devices with desired properties based on summed properties of parts and in configurations that cannot be obtained by using genetic engineering. This strategy will create optimized recombinant antibody devices at reduced costs and with shortened development times.     

Metabolomics of Genetically Modified Crops

Metabolomic-based approaches are increasingly applied to analyse genetically modified organisms (GMOs) making it possible to obtain broader and deeper information on the composition of GMOs compared to that obtained from traditional analytical approaches. The combination in metabolomics of advanced analytical methods and bioinformatics tools provides wide chemical compositional data that contributes to corroborate (or not) the substantial equivalence and occurrence of unintended changes resulting from genetic transformation. This review provides insight into recent progress in metabolomics studies on transgenic crops focusing mainly in papers published in the last decade.     

Simulation of membrane chemical degradation in a proton exchange membrane fuel cell by computational fluid dynamics

Membrane chemical degradation is a major contributor to the still limited lifetime of proton exchange membrane (PEM) fuel cells. In the present work, this phenomenon is simulated by computational fluid dynamics (CFD). The main advantage of the CFD model is that it can provide the degradation profile across the cell active area. Results reveal that degradation accelerates when voltage, temperature and pressure are increased and when reactants humidity and membrane thickness are decreased. Moreover, membrane deterioration is found to be more severe where oxygen pressure is higher, and more heterogeneous when oxygen distribution is less uniform. Generally, conditions that increase current production and thus oxygen depletion along the cell increase degradation heterogeneity. The flow field design is also found to influence the membrane degradation spatial profile. The modeling strategy here applied, the incorporation of a degradation sub-model into a general-purpose CFD code, can be used to include other degradation mechanisms.     

Modification of coconut fibers with polyaniline for manufacture of pressure‐sensitive devices

This article studies the modification of coconut fibers with polyaniline (PAni) with help of statistical experimental design techniques. The main factors studied here were the techniques used for particle dispersion (sonication vs. magnetic stirring) and the type of initiator (ammonium persulfate, APS, vs. ammonium cerium sulfate dihydrate, Ce(IV)). The obtained materials were characterized through low field nuclear magnetic resonance, small‐and wide‐angle X‐ray scattering, scanning electron microscopy, fourier transform infrared spectroscopy, and ultraviolet–visible spectroscopy. Additionally, the electrical resistivities and respective sensitivities to variations of the applied pressure were evaluated for all obtained samples, with help of standard volume resistivity measurements and electro‐mechanical tests. The materials prepared through magnetic stirring with APS presented the best electrical and electromechanical properties, although materials prepared through sonication with Ce(IV) also presented good electrical and electromechanical properties and could be prepared much faster. As a consequence, modification of coconut fibers with PAni, using sonication as the particle dispersion technique and Ce(IV) as initiator, constitutes a very promising procedure for manufacture of pressure‐sensitive devices. POLYM. ENG. SCI., 54:2887–2895, 2014. © 2014 Society of Plastics Engineers     

Effects of different particle deposition parameters on adhesion of resin cement to zirconium dioxide and phase transformation

This study evaluated the effect of air-abrasion parameters such as particle size, distance, and time on adhesion of resin cement to zirconium dioxide (Y-TZP) and t→m phase transformation. Y-TZP blocks (N = 80) (In-Ceram YZ, Vita) (4 mm^3?×?4 mm^3?×?3 mm³) were assigned into eight groups (n = 10): air-abrasion with 30 μm (CoJet Sand, S30) and 110 μm (Rocatec-Plus, S110) silica-coated alumina particles, applied for either for 10–20 s (T = time), from a distance of 10–20 mm (D = distance), composing the following groups: S₃₀T₁₀D₁₀, S₃₀T₁₀D₂₀, S₃₀T₂₀D₁₀, S₃₀T₂₀D₂₀, S₁₁₀T₁₀D₁₀, S₁₁₀T₁₀D₂₀, S₁₁₀T₂₀D₁₀, and S₁₁₀T₂₀D₂₀. Resin composite (RelyX ARC) was bonded to Y-TZP blocks in polyethylene molds. The specimens were aged (10,000 thermal cycles and water storage for 90 days) prior to shear bond test. Failure types were analyzed under stereomicroscope and SEM, and phase transformation was calculated. Data (MPa) were analyzed using 3-way ANOVA and Tukey’s tests. Air-abrasion with 110 μm silica particles (10.96) presented significantly higher bond strength (p = 0.0149) compared to 30 μm (8.96). Time (p = 0.403) and distance (p = 0.179) parameters did not affect the results significantly. Air-abrasion with 110 μm particles (12.3) promoted higher bond strength than that of 30 μm (6.4) when applied for 10 s from a distance of 10 mm (Tukey’s). Failure types were predominantly adhesive. Phase transformation ranged between 30.3 and 35.9% for 30 μm particles and 23.8–43.7% for 110 μm particles. While the size of silica-coated alumina particles were more relevant parameter for resin cement adhesion to Y-TZP, time (up to 20 s) and distance (up to 20 mm) appear to be less pertinent.