In-laboratory removal of femoral sheath following protamine administration in patients having intracoronary stent implantation

Two hundred twenty-eight patients with successful coronary stent implantation were randomized either to protamine administration and femoral sheath removal (group I, n = 117) or no heparin neutralization and delayed sheath removal (group II, n = 111). The hospital stay after treatment was shorter in patients receiving protamine; therefore, protamine use for neutralizing circulating heparin may be safely administered immediately after stent implantation.     

气—液式热管换热器在硫酸工业中的应用研究

本文研制的气－液式热管换热器应用于硫酸生产中ＳＯ３气体的余热回收。它具有传热性能好、流动阻力小、寿命长、体积小、节能效果显著和易清垢等优点。     

变结构变参数设计方法及其在机械CAD中的应用

提出了一种新颖的机械结构设计思想－变结构变参数设计方法，并结合实例，阐述了变结构变参数设计的概念、原则、实施措施和意义。由此对Ｉ－ｄｅａｓ软件包进行了二次开发，编制了发动机曲轴专用ＣＡＤ软件程序，并用某型号发动机曲轴进行了验证。     

Assessment model of dam operation risk based on monitoring data

Although the dams produce remarkable social and economic benefits, the threat made by unsafe dams to the life and property of people who live in the lower river area is un-negligible. Based on the monitoring data which reflect the safety condition of dams, the risk degree concept is proposed and the analysis system and model for evaluating risk degree (rate) are established in this paper by combining the reliability theory and field monitoring data. The analysis method for risk degree is presented based on Bayesian approach. A five-grade risk degree system for dam operation risk and corresponding risk degree is put forward according to the safety condition of dams. The operation risks of four cascade dams on some river are analyzed by the model and approach presented here and the result is adopted by the owner.     

薄板坯连铸连轧工艺对铌微合金化高强度钢组织和性能的影响

首先建立薄板坯连铸连轧工艺的试验室模拟技术，并运用该模拟技术，研究薄板坯连铸连轧工艺(CSP)和传统板坯再加热工艺(TRP)两种工艺对铌微合金化高强度钢的显微组织和力学性能的影响。研究结果表明：CSP钢的晶粒细化效果不如TRP钢，两者的平均铁素体晶粒尺寸分别为8．17μm和6．30μm。在CSP试验钢板中铌的析出量较大，特别是在铁素体中细小颗粒的铌的析出物较多，沉淀强化效果较强。CSP试验钢的σ0.5和σb分别较TRP工艺低约40MPa和约25MPa，同时其低温冲击韧性较好，FATT温度较低。     

Formation and retention of local melted films in AZ91 friction stir spot welds

The formation of local melted films during friction stir spot welding of as-cast AZ91D and thixomolded AZ91 material is investigated. The average temperatures close to the tip of the rotating pin vary from 438 to 454 °C during the dwell period in friction stir spot welding. These measured temperature values are higher than the melting temperature of α-Mg + Mg₁₇Al₁₂ eutectic (437 °C). It is suggested that the temperature in the stir zone during the dwell period is determined by the relative proportions of α-Mg and (α-Mg + Mg₁₇Al₁₂) eutectic material, which are incorporated during friction stir spot welding. Based on the stir zone temperature measurements and a detailed examination of material located at the root of the pin thread it is suggested that material is moved downwards via the pin thread and into the stir zone during the dwell period in friction stir spot welding. Evidence of local melted film formation is observed in the stir zone of AZ91 spot welds. It is suggested that melted films are retained since their dissolution rate is much slower in the high temperature stir zone than it is when melted films is formed in the stir zone during Al 7075-T6 friction stir spot welding. The spontaneous melting temperature, solute diffusion rate and the thermodynamic driving force for droplet dissolution are much higher during Al 7075-T6 friction stir spot welding.     

合成2,4-二叔丁基苯酚工业试验

以离子交换树脂为催化剂，苯酚和甲基叔丁基醚为原料合成2，4-二叔丁基苯酚(简称2，4酚)，合成产物经过滤再经间歇真空精馏精制提纯，得到高纯度的2，4酚成品。成品精馏后釜中残液在酸性白土催化剂的作用下通过歧化反应生成对叔丁基苯酚，再经精馏提纯得到成品对叔丁基苯酚。通过工艺优化，使2，4酚、对叔丁基苯酚形成联产生产工艺，降低了生产原料消耗和成本。     

An alternative method to compute the component fractions in the geometrical optical model: visual computing method

A method called visual computing was used to solve angular four-components' proportions and directional vegetation cover fraction for discrete canopies and continuous row-planted plants. It proved effective to predict the angular characteristics on pixel scale. The method could be an alternative way to a classical solution of geometrical optical models. A visual computing method would be effective especially when the canopies' spatial distribution and shapes were irregular and could not be described statistically.     

脉冲电镀最佳参数之探索和优化

本文利用正交实验法对脉冲电镀各控制参数进行试验,对影响分散能力、镀层可靠性及外观质量的各种因素进行探讨,寻找影响外观质量的显著因子并加以控制,同时进一步优化脉冲电镀的工艺参数。