Rapid Quenching Technique Using Thermal-Image Furnace for Glass Preparation

A new technique combining a thermal-image furnace and a twin roller is described for quenching the melt to form glass. The technique was applied to the simple system Li₂O-SiO₂, since its fundamental parameters in the estimation of critical cooling rate are available. Glass flakes were obtained in the composition Li₄SiO₄, for which a very large critical cooling rate (∼10⁹ K·s⁻¹) was needed for glass formation.     

Decomposition of chlorofluorocarbons on TiO2ZrO2

The decomposition of chlorofluorocarbons (CFCs) in the presence of water was examined over a variety of solid acid catalysts. The TiO₂ZrO₂ catalyst was found to have the highest activity and longest life among the catalysts examined. The activity of the TiO₂ZrO₂ catalysts depended upon the content of TiO₂. At the contents of TiO₂ from 58 to 90 mole%, the TiO₂ZrO₂ catalysts exhibited high activity, and these catalysts were proven to contain TiZrO₄ crystal. From the study of the XRD peak intensity of the TiZrO₄ crystal, it was highest on the TZ-58 which contained 58 mole% of TiO₂, and decreased with increasing the content of TiO₂. Furthermore, the conversion of CFC113 measured at 673 K was highest at TZ-58, and decreased gradually with increasing TiO₂ content. Therefore, the TiZrO₄ crystal influences the activity of decomposition of CFC113. However, the TiO₂ZrO₂ catalyst was gradually deactivated during the reaction due to the elimination of titanium atoms. A good relationship was found between the activity on TiO₂ZrO₂ catalyst and bond energy of CCl in the compounds of chlorofluorocarbons and hydrochlorocarbons, suggesting that the rate controlling step was the cleavage of CCl bond.     

Effect of medium-chain fatty acid positional distribution in dietary triacylglycerol on lymphatic lipid transport and chylomicron composition in rats

The present study was carried out to examine if the positional distribution of medium-chain fatty acid (MCF) in dietary synthetic fat influences lymphatic transport of dietary fat and the chemical composition of chylomicrons in rats with permanent cannulation of thoracic duct. Four types of synthetic triacylglycerol were prepared: (i) sn-1(3) MCF-sn 2 linoleic acid, (ii) interesterified sn-1(3) MCF-sn 2 linoleic acid, (iii) sn-2 MCF-sn-1(3) linoleic acid, and (iv) interesterified sn-2 MCF-sn-1(3) linoleic acid. A purified diet composed of equal amounts of the synthetic fat and cocoa butter was given to rats with permanent lymph duct cannulation. The positional distribution of MCF in the dietary fat had no significant effect on the lymph flow, triacylglycerol output, phospholipid output, lipid composition of chylomicrons, or the particle size. The positional distribution of MCF in the synthetic triacylglycerol was maintained in the chylomicron triacylglycerol. These results showed that MCF in the dietary triacylglycerol is transported into lymphatics and the positional distribution is well preserved in chylomicron triacylglycerol.     

Calibration Curve for Quantitative Analysis of the Monoclinic-Tetragonal ZrO2 System by X-Ray Diffraction

A nonlinear calibration curve for volume fraction vs integrated intensity ratio was obtained for the monoclinic-tetragonal ZrO² system by using X-ray powder pattern-fitting and pattern-decomposition techniques. The empirical equation agrees well with the theoretical one. By using this equation, the deviation from linearity (6.8% maximum) resulting from the intensity difference of corresponding reflections of the two phases can be estimated quite accurately.     

Structure Evolution of Highly Crystallized BaWO4 Film Prepared by an Electrochemical Method at Room Temperature

Highly crystallized BaWO₄ films have been prepared on a tungsten substrate in an alkaline solution containing barium ions by an electrochemical method with a constant direct current density of 1 mA/cm² at room temperature (25°C). The average grain size was about 13 μm, and the thickness about 9 μm after a treatment time of 35 min. The dependence of cell voltage on deposition time was divided into three steps: conduction, anodic oxidation, and breakdown steps. The BaWO₄ film formed during the first step. Electrochemical dissolution of metal tungsten occurred with an accompanying positive change of overpotential in the first step. The crystallization of BaWO4 was characterized by three-dimensional nucleation. In the second step, an amorphous tungsten oxide film formed, thereby increasing the potential. An electrical breakdown occurred in the third step, and the breakdown voltage (about 90 V) was practically the same as those of anodic tungsten oxide films.     

Fracture toughness of silica particulate‐filled epoxy composite

The relationship between the postcuring conditions and fracture toughness on three silica particulate‐filled epoxy composites was investigated. The glass transition temperature, T_g, and the fragility parameter, m, derived from the thermo‐viscoelasticity, were used to characterize the composites, which were postcured under various conditions. The glass transition temperature and fragility both depended on both of the curing conditions and the volume fraction of silica particles. The glass transition temperature increased with the postcuring time and temperature, while the fragility generally decreased as the volume fraction increased. There was no direct correlation between the glass transition temperature and fragility. The fracture toughness depended on both the glass transition temperature and fragility. The composites with a high glass transition temperature and low fragility had high fracture toughness. These results indicate that the glass transition temperature and fragility are useful parameters for estimating the fracture toughness of the silica particulate‐filled epoxy composites. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2261–2265, 2002     

Effects of Pre-Treatment of a Silica-Supported Gallium Oxide Catalyst with H2 on Its Catalytic Performance for Dehydrogenation of Propane

The pre-treatment of a silica-supported gallium oxide catalyst with H₂ at 823 K increased the yield of aromatics and the selectivity to aromatics in the dehydrogenation of propane over the catalyst at 823 K. Gallium oxide in the catalyst was partially reduced with H₂ at 823 K. NH₃ desorption and DRIFTS studies on the gallium oxide catalyst suggest that the dehydrogenation of propane over a silica-supported gallium oxide catalyst would proceed in the following way: (1) the dehydrogenation of propane to produce propene would occur on Ga sites including Ga^δ+–H sites and (2) the aromatization of propene to aromatics on Ga–O–H acid sites.     

On-chip fabrication of magnetic alginate hydrogel microfibers by multilayered pneumatic microvalves

Alginate hydrogel has widespread applications in tissue engineering, cancer therapy, wound management and drug/cell/growth factor delivery due to its biocompatibility, hydrated environment and desirable viscoelastic properties. However, the lack of controllability is still an obstacle for utilizing it in the fabrication of 3D tissue constructs and accurate targeting in mass delivery. Here, we proposed a new method for achieving magnetic alginate hydrogel microfibers by dispersing magnetic nanoparticles in alginate solution and solidifying the magnetic alginate into hydrogel fiber inside microfluidic devices. The microfluidic devices have multilayered pneumatic microvalves with hemicylindrical channels to fully stop the fluids. In the experiments, the magnetic nanoparticles and the alginate solution were mixed and formed a uniform suspension. No aggregation of magnetic nanoparticles was found, which is crucial for flow control inside microfluidic devices. By regulating the flow rates of different solutions with the microvalves inside the microfluidic device, magnetic hydrogel fibers and nonmagnetic hydrogel fibers were fabricated with controlled sizes. The proposed method for fabricating magnetic hydrogel fiber holds great potential for engineering 3D tissue constructs with complex architectures and active drug release.     

Fracture toughness of bisphenol A‐type epoxy resin

The relationship between the postcuring conditions and the fracture toughness of a bisphenol A‐type epoxy resin cured with acid anhydride was investigated. The glass transition temperature and fragility parameter, derived from the thermo‐viscoelasticity, were used to characterize the epoxy resin postcured under various conditions. Relationship between these two parameters and the fracture toughness was then investigated, based on the fractography results of a microscopic roughness examination of a fractured surface. The values of the glass transition temperature and fragility greatly depended on the postcuring conditions. The glass transition temperature was approximately 400 K when the crosslinking reaction was saturated. The fragility was independent of the saturation of the reaction and varied between 50 and 180. The results of the fracture test and fractography examination showed that there was no direct correlation between the glass transition temperature, the fracture toughness, and the roughness. On the other hand, there was a correlation between the fragility, fracture toughness, and roughness when the glass transition temperature saturated (at 400 K). As the fragility decreased from 180 to 50, the fracture toughness increased from 0.6 to 1.1 MPa · m^1/2 at the same glass transition temperature. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 10: 2266–2271, 2002     

Measurement of zeolite,silicate, and phosphate in laundry detergent products by inductively coupled plasma atomic emission spectrometry

This paper reports the development of a method for simultaneously measuring zeolite, silicate, and phosphate in laundry detergent products by inductively coupled plasma atomic emission spectrometry. A sample is decomposed under alkaline oxidative conditions to decompose zeolite, silicate, phosphate, and organic substances. Then hydrochloric acid is added to the decomposed solution to dissolve aluminum hydroxide precipitate before analysis. This sample preparation procedure was investigated by using a total organic carbon analyzer and was confirmed to be applicable to simultaneous measurements of zeolite, silicate, and phosphate. Relative standard deviation for the analysis is less than 2.1%, recovery is more than 99.0%, and the calibration curve gives a correlation coefficient ofR=1.000. The detection limit of this method for aluminum and silicon is 0.1%, and for phosphorus, 0.2% by weight in the product. This method is applicable to various laundry detergent products that contain zeolite, silicate, or phosphate and is five times faster than the three wet chemical methods.