Towards the realistic planning of GMPLS-based optical transport networks

The multi-granular switching concept defined in Generalized Multiprotocol Label Switching (GMPLS) is expected to be a future-proof solution for mitigating the Optical Crossconnet scalability problems associated with the skyrocketing growth of traffic in optical transport networks. In this paper, we address the problem of planning the GMPLS-based (or multi-granular) transport network with color (or label) conversion and signal regeneration capabilities. The objective of the problem is to minimize the total weighted port count in the transport network. The novelty of this problem lies in the incorporation of the following for the first time: (1) considering all traffic granularities defined in GMPLS; (2) allowing wavelength, waveband, and fiber conversions; (3) considering the optical-reach limitation of optical signals; and (4) customizing the optical reach of all-optical paths. Due to the computational complexity of the problem, we propose various efficient heuristics that are capable of solving large-sized problems in a reasonable amount of time. In order to achieve the best possible solution to the planning problem, a comprehensive evaluation of different heuristic variations through illustrative examples and simulations is conducted. The results also provide valuable insights into many issues that can contribute to further research and development in this area.     

Treatment of olive mill washing water by ultrafiltration

Olive oil production requires important quantities of washing water containing low oil concentrations, but classical processes used to recover or to eliminate this oil are ineffective. This study presents a membrane technique to treat olive oil mill washing water using different commercial ultrafiltration membranes: one organic (PCI) and two ceramic (Ceraver) membranes. The influence of the hydrodynamic parameters (transmembrane pressure and flow rate) and the cut‐off membranes on the efficiency of the ultrafiltration process was evaluated, and it was shown the organic PCI membrane could reduce pollution due to organic matter by decreasing the value of the Chemical oxygen demand by about 90%. Moreover, the nature of the ultrafine pore membrane appeared to be an important parameter which may strongly increase or decrease the capacity of the membrane. The membrane cut‐off did not have a strong influence on the performance of the process but if the membrane pores were too large the stability of the dynamically formed membrane decreased at transmembrane pressures greater than 0.2 MPa.     

Theoretical Analysis of the Onset of Gas Entrainment from a Stratified Region through a Single Side‐Oriented Branch at Moderate Froude Numbers

A theoretical investigation has been conducted for the prediction of the critical height at the onset of gas entrainment during single discharge from a stratified, two‐phase region, through a branch installed on an inclined flat wall. The predicted critical height at the onset of gas entrainment was proven to be a function of Froude number (Fr) and density ratio of the interface fluids. Three different experimental data sets at wall inclination angles of zero, 45 and 90 degrees (i.e. side, inclined and bottom branches) were used for comparisons. A good concurrence was illustrated between the experimental and theoretical values.     

État de l’art de la gestion de cache logiciel pour tolérer les déconnexions en environnements mobiles

Recent years have seen a rapid evolution in the hardware and in networks used in mobile computing environments. This evolution has opened up new opportunities for mobile computing. Mobile computing allows a mobile user to access various kinds of information any time anywhere. However, mobile computing raises the problem of data availability in the presence of disconnections. Thus, distributed applications and middleware in mobile environments must be adapted to cope with disconnections. In this article, we present a state of the art on software caching for tolerating disconnections in mobile environments. The structure of the article follows the type of entities manipulated by the distributed applications : ordinary files, databases, web pages, objects, and components.     

Heat transfer augmentation for air jet impinged on a rough surface

An experimental investigation of heat transfer from a round air jet impinging normally from below onto a heated square plate was performed. The objective of the investigation was to study the effect of roughness on both the heat transfer and the fluid flow characteristics. Smooth and rough plates were, therefore, used in the course of the experiments. The heat transfer data were collected for four jet Reynolds numbers, ranging from 6500 to 19 000. The Reynolds numbers are based on the jet-exit velocity (U_e) and the nozzle-exit diameter (D), Re_e=U_eD/ν. The nozzle-to-plate distance ranged from 0.05 to 15 nozzle-exit diameter to cover both the potential core and the far regions of the jet flow. The roughness was composed of cubes of 1 mm dimension distributed uniformly along the plate. The local and average Nusselt number values for the rough plate showed an increase ranging from 8.9% to 28% over those for the smooth plate. Roughness was found to have a strong effect on the flow characteristics; it affected the mean velocity as well as the turbulence intensity of the flow. The mean velocity profiles for the smooth case at radial distances of r/D=1 and r/D=2.5 showed steeper near-wall velocity gradients compared with the profiles of the rough case, where r is the radial distance measured from the plate center along the plate centerline. In addition, roughness caused an increase in the turbulence intensity of the flow.     

Microstructure investigation and thermal stability of 99.1% aluminum processed by equal channel angular extrusion

Microstructure evolution of 99.1% aluminum after equal-channel angular extrusion (ECAE) and subsequent heat-treatment was investigated. After deformation the samples were annealed at different temperatures. The deformed and annealed states were characterized by Transmission Electron Microscopy (TEM), X-ray diffraction (XRD), and microhardness tests. It was shown that the observed microstructure changes during subsequent annealing have to be associated with recovery and cells formation. The initial stages of recovery were investigated using weak-beam technique. The microstructure obtained after annealing for 1 h at 100 °C consists of some arrangements of the dislocations into sub-grain boundaries within the wide preexisting grains. Annealing at 300 °C led to the appearance of a duplex microstructure consisting of bands of slightly coarsened grains associated with refined grains. No growth of dislocation cells was observed up to 400 °C. In XRD measurements, the lattice parameter increase with subsequent heating. This indicates a continuous grain growth during annealing. This is due to the important increase of coherency length, D observed parallel to a substantial decrease of rms-strain, ε.     

Cold Thermal Storage and Peak Load Reduction for Office Buildings in Saudi Arabia

This paper involves the investigations of the chilled water and ice cold thermal storage technologies along with the associated operating strategies for the air conditioning(AC) systems of the typical office buildings in Saudi Arabia, so as to reduce the electricity energy consumption during the peak load periods. In Saudi Arabia, the extensive use of AC for indoor cooling in offices composes a large proportion of the annual peak electricity demand. The very high temperatures over long summer periods, extending from May to October, and the low cost of energy are the key factors in the wide and extensive use of air conditioners in the kingdom. This intense cooling load adds up to the requirement increase in the capacity of power plants, which makes them under utilized during the off-peak periods. Thermal energy storage techniques are one of the effective demand-side energy management methods. Systems with cold storage shifts all or part of the electricity requirement from peak hours to off-peak hours to reduce demand charges and/or take advantage of off-peak rates. The investigations reveal that the cold thermal energy storage techniques are effective from both technical and economic perspectives in the reduction of energy consumption in the buildings during peak periods.     

Modeling and Analysis of Workflows Using Petri Nets

A workflow system, in its general form, is basically a heterogeneous and distributed information system where the tasks are performed using autonomous systems. Resources, such as databases, labor, etc. are typically required to process these tasks. Prerequisite to the execution of a task is a set of constraints that reflect the applicable business rules and user requirements.In this paper we present a Petri Net (PN) based framework that (1) facilitates specification of workflow applications, (2) serves as a powerful tool for modeling the system under study at a conceptual level, (3) allows for a smooth transition from the conceptual level to a testbed implementation and (4) enables the analysis, simulation and validation of the system under study before proceeding to implementation. Specifically, we consider three categories of task dependencies: control flow, value and external (temporal).We identify several structural properties of PN and demonstrate their use for conducting the following type of analyses: (1) identify inconsistent dependency specifications among tasks; (2) test for workflow safety, i.e. test whether the workflow terminates in an acceptable state; (3) for a given starting time, test whether it is feasible to execute a workflow with the specified temporal constraints. We also provide an implementation for conducting the above analyses.     

IR spectroscopic study on the thermal degradation of plastic security cover sheets of some documents

The change in IR spectra of plastic security cover sheets of ethylene vinylacetate copolymer during thermal treatment was investigated. The results obtained revealed that the temperature reduced the concentration of the ester group; moreover, the carbonyl band disappeared at high temperatures from 200 to 220°C, as well as broading of the absorption aliphatic–CH band. The change in the mechanical properties, degree of swelling in water, and refractive index of the samples during thermal treatment were also investigated. © 1993 John Wiley & Sons, Inc.     

Differential effects of ethanol on baroreceptor heart rate responses of conscious spontaneously hypertensive and normotensive rats

This study investigated the acute effects of ethanol (0.25, 0.5, or 1 g/kg, iv) on mean arterial pressure, heart rate, and gain of the baroreceptor reflex control of heart rate (BRS) in conscious spontaneously hypertensive rats (SHRs) and age-matched Wistar rats. BRS was substantially lower in the SHRs as compared with the Wistar rats when measured by phenylephrine (-0.95 +/- 0.16 vs. -2.02 +/- 0.22 beats/min/mm Hg) or nitroprusside (-1.90 +/- 0.2 vs -3.02 +/- 0.32 beats/min/mm Hg). None of the doses of ethanol influenced BRS in the SHR. In contrast, ethanol attenuated BRS in Wistar rats, but this effect was dependent on the dose used and the type of response. The lower doses attenuated the reflex tachycardic response, but had no effect on the reflex bradycardic response. On the other hand, the 1 g/kg dose of ethanol attenuated the reflex bradycardic but not the tachycardic response. Ethanol produced a pressor effect (15-25 mm Hg; 5-min duration), which was neither dose- nor strain-dependent. However, only in the SHR mean arterial pressure remained elevated (10-15 mm Hg above control) for 20 min in response to the 0.5 g/kg dose of ethanol, and its recovery coincided with the occurrence of a slowly developing negative chronotropic response. Ethanol produced a dose-related negative chronotropic effect in both strains of rats that was of longer duration in the SHR, particularly with the 1 g/kg dose. It is possible that the bradycardic effect of ethanol influenced negatively its pressor effects.(ABSTRACT TRUNCATED AT 250 WORDS)