Design and synthesis of side-chain optimized poly(2,6-dimethyl-1,4-phenylene oxide)-g-poly(styrene sulfonic acid) as proton exchange membrane for fuel cell applications: Balancing the water-resistance and the sulfonation degree

Side-chain optimized poly (2,6-dimethyl-1,4-phenylene oxide)-g-poly (styrene sulfonic acid) (PPO-g-PSSA) is designed with balanced water-resistance and sulfonation degree. The PPO-g-PSSA is synthesized by controlled atom-transfer radical polymerization (ATRP) from brominated poly (2,6-dimethyl-1,4-phenylene oxide) (PPO-xBr) and ethyl styrene-4-sulfonate and followed by hydrolysis. A series of PPO-g-PSSA are prepared possessing different bromination degree (x) of PPO-xBr and polymerization degree (m) of the side-chains and the water-resistances of the fabricated membranes are investigated. The results show that a PPO-g-PSSA at relatively low x (x < 0.2) and high m (m > 4) exhibits good balance between the water-resistance and the sulfonation degree. Namely, it displays suitable proton conductivity with compromised water-resistance. Moreover, a maximum ion exchange capacity (IEC) of 3.24 mmol g^?1 is reached without the sacrifice of water-resistance. In addition, PPO-g-0.08PSSA-13 and PPO-g-0.14PSSA-4 are chosen characterized by thermogravimetric analysis, proton conductivities and mechanical properties. At 90% RH, the optimized PPO-g-0.08PPSA-13 possesses a proton conductivity of 37.9 mS cm^?1 at 40 °C and 45.5 mS cm^?1 at 95 °C, respectively.     

Chromium evaporation and oxidation characteristics of alumina-forming austenitic stainless steels for balance of plant applications in solid oxide fuel cells

The chromium (Cr) evaporation behavior of several different types of iron (Fe)-based AFA alloys and benchmark Cr₂O₃-forming Fe-based 310 and Ni-based 625 alloys was investigated for 500 h exposures at 800 °C to 900 °C in air with 10% H₂O. The Cr evaporation rates from alumina-forming austenitic (AFA) alloys were ~5 to 35 times lower than that of the Cr₂O₃-forming alloys depending on alloy and temperature. The Cr evaporation behavior was correlated with extensive characterization of the chemistry and microstructure of the oxide scales, which also revealed a degree of quartz tube Si contamination during the test. Long-term oxidation kinetics were also assessed at 800 to 1000 °C for up to 10,000 h in air with 10% H₂O to provide further guidance for SOFC BOP component alloy selection.     

老旧建筑结构改造加固

从老旧建筑结构现状展开论述，详细阐述了砌体墙加固设计、构造柱与圈梁加固设计、基础结构加固设计这几种老旧建筑结构改造加固设计，实现了对建筑结构改造工程施工技术的深入分析，希望能够为城乡建设事业的发展提供助力。     

Experimental Study of Oilfield Water Plugging with Organic Chromium Gel

Chemistry and Technology of Fuels and Oils - Application of water flooding technologies in the oilfield causes intensive heterogeneity of the oil reservoir and improper circulation of the injected...     

Structural,optical and electrical properties of indium doped Cu2ZnSn(S,Se)4 thin films synthesized by the DC and RF reactive magnetron cosputtering

Element doping into the Cu₂ZnSn(S,Se)₄ (CZTSSe) absorber is an effective method to optimize the performance of thin film solar cells. In this study, the Cu₂In_xZn_1-xSn(S,Se)₄ (CIZTSSe) precursor film was deposited by magnetron cosputtering technique using indium (In) and quaternary Cu₂ZnSnS₄ (CZTS) as targets. Meanwhile, the In content was controlled using the direct current (DC) power on In target (P_In). A single kesterite CIZTSSe alloy was formed by successfully doping a small number of In³⁺ into the main lattice of CZTSSe. The partial Zn²⁺ cations were substituted by In³⁺ ions, resulting in improving properties of CZTSSe films. Morphological analysis showed that large grain CIZTSSe films could be obtained by doping In. The well-distributed, smooth, and dense film was obtained when the P_In was 30 W. The band gap of CIZTSSe could be continuously adjusted from 1.27 to 1.05 eV as P_In increased from 0 to 40 W. In addition, the CIZTSSe alloy thin film at P_In = 30 W exhibited the best p-type conductivity with Hall mobility of 6.87 cm²V^?1s^?1, which is a potential material as the absorption layer of high-performance solar cells.     

Improvement of polyamide/thermoplastic polyurethane blends with polyamide 6-polyurethane copolymer prepared via suspension polymerization as compatibilizer

The polyamide 6-polyurethane copolymer (PA6-b-PU-b-PA6) was synthesized through anionic suspension polymerization and then mixed with polyamide 6/thermoplastic polyurethane (PA6/TPU) and polyamide 6, 6/thermoplastic polyurethane (PA66/TPU) blends using as the compatibilizer. The results show that the PA6-b-PU-b-PA6 copolymers powders several can be obtained through suspension polymerization using dimethicone as disperse medium. The average diameter of PA6-b-PU-b-PA6 copolymer powders decreased with the increasing of PU content. With the addition of PA6-b-PU-b-PA6, the TPU phase dispersed more uniformly in PA6 or PA66 matrix, and the size of TPU dispersed phase decreased obviously. The PA6-b-PU-b-PA6 copolymer with higher PU content shows better compatibilizing effect. Addition of PA6-b-PU-b-PA6 can improve both strength and toughness of the PA/TPU blends. When the amount of PA6-PU25% copolymer was 5 phr, the tensile strength and notched impact strength of PA6/TPU/PA6-PU25% blends increased 29 and 159.4%, respectively, compared to the PA6/TPU blend without compatibilizer.     

基于局部分型面的电器外壳注塑模具设计

电器外壳制品形状结构复杂,有两处侧凸(孔)较难处理。通过对矩形孔内侧凸的结构分析,在其局部设计了分型面,避免了使用侧向抽芯机构;对侧孔部位设计了斜顶杆侧向抽芯机构,其结构简单、紧凑。模具采用一模二腔、平衡式布局,采用经扁推杆由制品内部进料的潜伏式浇口,S型流道。在NX 8.0中完成了模具结构设计。经实践证明,该模具结构合理,产品合格。     

植物细胞分裂素ortho-Topolin Riboside对人白血病细胞株THP-1的抗癌活性及机制初探

本研究以人急性髓性白血病细胞株THP-1为研究对象,初步探讨其抗癌活性及作用机制。通过光学显微镜观察N6-2-苄胺羟基腺苷(oTR)作用后THP-1细胞形态学和数目变化;CCK-8法检测oTR对THP-1细胞的增殖抑制作用,并用核苷转运体拮抗剂和腺苷受体拮抗剂预处理细胞检测oTR进入细胞的方式;用流式细胞仪分析oTR作用对THP-1细胞凋亡和分化的影响。结果表明,oTR可显著(P<0.05)抑制THP-1细胞的增殖能力,且呈浓度依赖性;核苷转运体拮抗剂Dipyridamole预处理THP-1细胞后,可明显逆转oTR的增殖抑制作用,而4种腺苷受体拮抗剂(DPCPX、SCH58261、MRS1754和MRA1191)则无显著影响;oTR可诱导处理组细胞亚倍体峰比例显著(P<0.05)高于对照组,且细胞髓系分化标志蛋白CD11b表达明显升高。以上结果表明细胞分裂素oTR通过核苷转运体途径进入THP-1细胞,显著(P<0.05)抑制细胞的增殖,并可诱导THP-1细胞发生凋亡和髓系分化。     

Ni-P/HZSM-5催化木质素降解制备酚类化学品

采用Ni-P复合改性HZSM-5催化剂催化木质素降解制备高附加值的单酚类化学品，探讨了催化剂种类、金属负载量、反应温度、反应时间以及溶剂种类对木质素催化降解制备酚类化合物的影响。同时采用X射线衍射仪（XRD）、比表面积和孔径分析仪（BET）、化学吸附仪（NH₃-TPD）、热重分析仪（TG）以及气相色谱质谱联用仪（GC/MS）对催化剂以及液相产物进行分析表征，同时探讨其催化失活以及再生机制。结果表明：Ni、P高度分散在HZSM-5催化剂的表面，Ni的添加有效地弱化了C－C键，致使β-O-4和α-O-4发生断裂，有效地提高了木质素加氢解聚的活性，减少了焦炭的生成，但催化剂的再生水热稳定性较差，重复使用性较低。当采用甲醇为供氢试剂，在反应温度为220℃，氢气压力为2MPa，反应时间为8h，催化剂负载量为10%，NaOH为共催化剂时，其木质素的转化率为98.6%，酚类化合物的含量达到74.97%。产物以苯酚、愈创木酚和紫丁香酚为主，低温促进了紫丁香酚的产生。