Passive alignment method of polymer PLC devices by using a hot embossing technique

A novel fabrication process using a hot embossing technique has been developed for micromechanical passive alignment of polymer planar lightwave circuit (PLC) devices. With only one step of embossing, single-mode waveguide straight channels and micropedestals for passive aligning are simultaneously defined on a polymer thin film with an accuracy of /spl plusmn/0.5 /spl mu/m. This process reduces the steps for fabricating alignment structures. A fabricated polymer PLC chip and fibers are combined on a v-grooved silicon optical bench (SiOB) in a flip-chip manner. The process provides a coupling loss as low as 0.67 dB per coupling face and a cost-effective packaging solution for various polymer PLC devices.     

High-performance MIM capacitor using ALD high-k HfO/sub 2/-Al/sub 2/O/sub 3/ laminate dielectrics

For the first time, we successfully fabricated and demonstrated high performance metal-insulator-metal (MIM) capacitors with HfO/sub 2/-Al/sub 2/O/sub 3/ laminate dielectric using atomic layer deposition (ALD) technique. Our data indicates that the laminate MIM capacitor can provide high capacitance density of 12.8 fF//spl mu/m/sup 2/ from 10 kHz up to 20 GHz, very low leakage current of 3.2 /spl times/ 10/sup -8/ A/cm/sup 2/ at 3.3 V, small linear voltage coefficient of capacitance of 240 ppm/V together with quadratic one of 1830 ppm/V/sup 2/, temperature coefficient of capacitance of 182 ppm//spl deg/C, and high breakdown field of /spl sim/6 MV/cm as well as promising reliability. As a result, the HfO/sub 2/-Al/sub 2/O/sub 3/ laminate is a very promising candidate for next generation MIM capacitor for radio frequency and mixed signal integrated circuit applications.     

土卡河电站工程及初期围堰挡水运行方式简介

介绍了土卡河水电站可研阶段通过方案比选后确定的工程规模(特征水位、装机容量)。为保证2006年底第一台机组发电,根据目前的施工进度,需要采用围堰挡水发电,文章简要介绍了第一台机组发电的运行方式。     

锂离子电池用聚合物电解质的最新进展II.含液聚合物电解质

由于干态聚合物电解质目前还不能满足聚合物锂离子电池的应用要求,人们致力于开发含液体增塑剂的聚合物电解质,包括凝胶型和微孔型两类体系。本文综述了含液聚合物电解质的最新进展,重点论述了各种新体系和新方法。     

氨精制装置运行问题分析及改造措施

通过分析中国石油兰州石化分公司炼油厂氨精制装置存在的运行问题,提出了相应的改造措施,包括在分凝器脱液管线上新增隔离阀门、更换三级冷凝冷却器、更换氨压缩机及采用低温结晶脱硫工艺等。改造后装置运行结果表明:三级分凝器出口温度由70℃降至小于35℃,压缩机吸气量由5 m3/m in提高至74 m3/m in,原料酸性水中硫化氢质量分数下降45.5%,氨质量分数下降55.5%,净化水合格率达100%,氨精制塔塔顶温度下降5~20℃,液氨中氨质量分数由97.05%上升至99.60%,液氨产量达0.125 t/h,实现了装置的长周期运行。     

晶须取向对SiCw/6061Al复合材料热压缩变形行为的影响

采用SEM 和 Magiscan-2A 图像分析系统研究了晶须取向对SiCw/6061Al复合材料在300℃压缩变形行为的影响.结果表明:晶须取向影响着晶须折断程度和转动角度; 随着晶须取向角的增加,晶须转动和折断行为所导致的软化效果下降.同时晶须取向也影响复合材料的热压缩应力-应变曲线的形状.在热压缩变形过程中,晶须取向角为0°和30°的复合材料表现出明显应变软化现象, 晶须取向角为45°的复合材料无明显软化现象.晶须取向角为90℃的复合材料表现出应变硬化现象.     

抗乙肝病毒表面抗原PreS1(20-47)的单链抗体在转基因烟草根分泌物中的初步表达

为探索利用植物根分泌表达重组蛋白的可行性，构建了含有抗乙肝病毒表面抗原PreS1(20—47)单链抗体(ScFv)基因的表达载体。该ScFv基因转化烟草后在烟草根部细胞的细胞质和内质网中获得表达。实验结果表明，5’端融合ER导向信号肽的重组ScFv可通过根分泌表达。     

监控系统协议仿真研究

通过分析监控系统的通讯协议,提出了利用计算机进行协议仿真,以串行接口为例给出一个通用的协议仿真软件,并介绍了若干个应用实例.     

Combining ideal beamforming and Alamouti space-time block codes

The simplest Alamouti space-time block code is coupled with a larger number of transmit antennas via ideal beamforming to achieve higher diversity gain. It is shown that the combined system can remain both full diversity and full code rate without orthogonality loss. Simulation results show a significant performance gain over the conventional space-time block codes.     

珠光体球化的分形研究

珠光体球化反映到金相上，是一种不规则图像的变化，并且具有分形的特征，可望用分形几何的方法来进行描述。以Cr-Mo钢的珠光体球化为例，用分形维数来描述珠光体球化程度；用小岛法对15CrMo钢的珠光体球化图谱进行了测量。实验表明，珠光体球化从1级到6级，其相应的分形维数范围为1.3156-1.9282。从电厂运行了10^5h的15CrMo钢管上取样，实测了该试样的珠光体球化等级，结果表明，以分形维数表示的球化程度与按图谱评定的球化等级完全吻合。