Induction of DNA-double-strand breaks by auger electrons from 99mTc complexes with DNA-binding ligands

The potential of certain Auger electron emitting nuclides for systemic radiotherapeutic applications has recently gained much attention. In particular, the ability of several nuclides, including 111In, 125I, and 123I, to induce DNA double-strand breaks (dsb), a good indicator of cytotoxicity, has been extensively studied. However, this ability has never previously been shown experimentally for 99mTc, which, besides the well-known gamma radiation that is used for diagnostic applications, also emits an average of 1.1 conversion electrons and 4 Auger or Coster-Kronig electrons per decay. Owing to the short range of Auger electrons, the radionuclide needs to be located very close to the DNA for dsb to occur. We synthesized two cationic 99mTcI-tricarbonyl complexes with pendant DNA binders, pyrene and anthraquinone. The X-ray crystal structures of the two complexes could be elucidated. Linear dichroism and UV/Vis spectroscopy revealed that the complex with pyrene intercalates DNA with a stability constant, K, of 1.1 x 10(6) M(-1), while the analogous complex with anthraquinone interacts with DNA in a groove-binding mode and has an affinity value of K=8.9 x 10(4) M(-1). We showed with phiX174 double-stranded DNA that the corresponding 99mTc complexes induce a significant amount of dsb, whereas non-DNA-binding [TcO4]- and nonradioactive Re compounds did not. These results indicate that the Auger electron emitter 99mTc can induce dsb in DNA when decaying in its direct vicinity and this implies potential for systemic radiotherapy with 99mTc complexes.     

Production of FAME from acid oil,a by-product of vegetable oil refining

Simple alkyl FA esters have numerous uses, including serving as biodiesel, a fuel for compression ignition (diesel) engines. The use of acid-catalyzed esterification for the synthesis of FAME from acid oil, a by-product of edible vegetable oil refining that is produced from soapstock, was investigated. Soybean acid oil contained 59.3 wt% FFA, 28.0 wt% TAG, 4.4 wt% DAG, and less than 1% MAG. Maximum esterification occurred at 65°C and 26 h reaction at a molar ratio of total FA/methanol/sulfuric acid of 1∶15∶1.5. Residual unreacted species under these conditions, as a fraction of their content in unesterified acid oil, were FFA, 6.6%; TAG, 5.8%; and DAG, 2.6%. This corresponds to estimated concentrations of FFA, 3.2%; TAG, 1.3%; and DAG, 0.2%, on a mass basis, in the ester product. In an alternative approach, the acylglycerol species in soapstock were saponified prior to acidulation. High-acid (HA) acid oil made from this saponified soapstock had an FFA content of 96.2 wt% and no detectable TAG, DAG, or MAG. Optimal esterification conditions for HA acid oil at 65°C were a mole ratio of FFA/methanol/acid of 1∶1.8∶0.17, and 14 h incubation. FAME recovery under these conditions was 89% of theoretical, and the residual unesterified FFA content was approximately 20 mg/g. This was reduced to 3.5 mg/g, below the maximum FFA level allowed for biodiesel, by washing with NaCl, NaHCO₃, and Ca(OH)₂ solutions. Alternatively, by subjecting the unwashed ester layer to a second esterification, the FFA level was reduced to less than 2 mg/g. The acid value of this material exceeded the maximum allowed for biodiesel, but was reduced to an acceptable value by a brief wash with 0.5 N NaOH.     

PORE-MOUTH POISONING OF NON-UNIFORM CATALYSTS

Impurity poisoning of a catalyst particle having a non-uniform activity distribution is analyzed. Equations that relate the position of the poison-front with time for different activity profiles are derived. It is shown that the effect of the activity distribution on the poisoning rate is apparent in the case of intraparticle-diffusion control. The performance of a non-uniform bifunctional catalyst in such conditions is also studied.     

Heat Induced Structure Modifications in Polymer‐Layered Silicate Nanocomposites

Summary: The success of the use of layered silicates in polymer nanocomposites, to improve physical and chemical properties is strictly related to a deeper knowledge of the mechanistic aspects on which the final features are grounded. This work shows the temperature induced structural rearrangements of nanocomposites based on poly[ethylene‐co‐(vinyl acetate)] (EVA) intercalated‐organomodified clay (at 3–30 wt.‐% silicate addition) which occur in the range between 75 and 350 °C. In situ high temperature X‐ray diffraction (HT‐XRD) studies have been performed under both nitrogen and air to monitor the modifications of the nanocomposite structure at increasing temperatures under inert/oxidative atmosphere. Heating between 75 and 225 °C, under nitrogen or air, causes the layered silicate to migrate towards the nanocomposite surface and to increase its interlayer distance. The degradation of both the clay organomodifier and the VA units of the EVA polymer seems to play a key role in driving the evolution of the silicate phase in the low temperature range. The structural modifications of the nanocomposites in the high temperature range (250–350 °C), depended on the atmosphere, either inert or oxidizing, in which the samples were heated. Heating under nitrogen led to deintercalation and thus a decrease of the silicate interlayer space, whereas exfoliation was the main process under air leading to an increase of the silicate interlayer space.

Heat induced structural modification of EVA‐clay nanocomposite under nitrogen and air.     

Dielectric Properties of the "Twinned" 8H-Hexagonal Perovskite Ba8Nb4Ti3O24

The dielectric properties of dense ceramics of the "twinned" 8H-hexagonal perovskite Ba₈Nb₄Ti₃O₂₄ are reported. Single-phase powders were obtained from the mixed-oxide route at 1325°C and ceramics (>92% of the theoretical X-ray density) by sintering in air or flowing O₂ at 1400°–1450°C. The ceramics are dc insulators with a band gap >3.4 eV that resonate at microwave frequencies with relative permittivity, ɛ_r∼44–48, quality factor, Q × f _r∼21 000–23 500 GHz (at f _r∼5.5 GHz) and temperature coefficient of resonant frequency, TC _f,∼+115 ppm/K.     

Natural fiber composites of high‐temperature thermoplastic polymers: Effects of coupling agents

Our earlier paper (Jana, S.C.; Prieto, A. J Appl Polym Sci 2002, 86, 2159) on the development of natural fiber composites of high‐performance thermoplastic polymers described a new methodology for the manufacturing of composite materials of a high‐temperature thermoplastic polymer, poly(phenylene ether) (PPE) and wood flour, a cellulosic natural filler. A thermosetting epoxy, used as a reactive solvent, reduced the processing temperature of PPE/epoxy blends to well below the decomposition temperature of natural fillers. In addition, the epoxy component, upon polymerization, formed coating layers around the filler particles to provide resistance against moisture diffusion and attacks by acids and alkali. This article describes the results of an investigation on two outstanding issues: (1) the influence of cellulosic wood particles and coupling agents on the speed of epoxy curing and reaction‐induced phase separation and (2) the effects of coupling agents on the morphology of crosslinked epoxy at the surfaces of natural fillers and mechanical properties of the composites. It was found that wood particles expedited epoxy curing in the composites; the extent of epoxy curing, however, was reduced in the presence of coupling agents. Also, the coupling agents promoted complete coverage of wood flour particles by polymerized epoxy, although the mechanical properties deteriorated over systems without coupling agents. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2168–2173, 2002     

Use of a sodium ionomer as a compatibilizer in polypropylene/high‐barrier ethylene–vinyl alcohol copolymer blends: The processability of the blends and their physical properties

The effect of a sodium ionomer (ion.Na⁺) on the compatibility of polypropylene (PP)/high‐barrier ethylene–vinyl alcohol copolymer (EVOH) blends was studied in terms of the thermal, mechanical, and optical properties and morphology. The rheological behavior, tensile tests, and morphology of the binary blends showed that the miscibility of EVOH with PP was very poor. The miscibility of the polymers improved with the ionomer addition. In general, the ion.Na⁺ concentration did not alter the thermal behavior of the blends, but it did improve the ductility of the injection‐molded specimens. Scanning electron micrographs displayed better adhesion between the PP and EVOH phases in the samples with the ionomer. The mechanical improvement was better in the film samples than in the injection‐molded samples. A 90/10 (w/w) PP/EVOH film with 5% ion.Na⁺ and an 80/20 (w/w) PP/EVOH film with 10% ion.Na⁺ presented better global properties than the other blends studied. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 1763–1770, 2004