Lessons from Earthquakes in Recent Times and their Effects on the Development of Geotechnology

This paper first reviews the earthquakes that occurred since 1995 and then outlines the significant lessons learnt from disasters. The discussion then goes into the induced development of engineering practices that were triggered by those disasters. It is clear that major development occurred in design philosophies, soil improvement, and facilities for research. The last section of this paper addresses the compound effects of earthquakes and rainfall that may make the extent of the disasters worse.     

Thermophysical properties of (U,Y)O2

We prepared polycrystalline pellets of (U,Y)O₂, containing YO_1.5 up to 11 mol.%. We performed indentation tests on the pellets, and evaluated the Young’s modulus and hardness. We measured the heat capacity and the thermal diffusivity, and evaluated the thermal conductivity. We succeeded in evaluating the effect of Y content on the thermophysical properties of (U,Y)O₂. We revealed that the Young’s modulus, hardness, and thermal conductivity of (U,Y)O₂ decreased with increasing the Y content.     

Wind Force Coefficients for Designing Porous Canopy Roofs

Wind force coefficients for designing porous canopy roofs have been investigated based on a series of wind tunnel experiments. Gable, troughed and mono-sloped roofs were tested. The roof models were made of 0.5 mm thick perforated duralumin plates, the porosity of which was changed from 0 to about 0.4. Overall aerodynamic forces and moments acting on the roof model were measured in a turbulent boundary layer with a six-component force balance for various wind directions. The results indicate that the wind loads on canopy roofs generally decrease with an increase in porosity of the roof. Assuming that the roof is rigid and supported by the four corner columns with no walls, the axial forces induced in the columns are regarded as the most important load effect for discussing the design wind loads. Two loading patterns causing the maximum tension and compression in the columns are considered. Based on a combination of the lift and moment coefficients, the design wind force coefficients on the windward and leeward halves of the roof are presented for the two loading patterns as a function of the roof pitch and porosity. The effect of porosity is taken into account as a reduction factor of the wind loads.     

Use of polyethylene films photografted with 2‐(dimethylamino)ethyl methacrylate as a potential adsorbent for removal of chromium (VI) from aqueous medium

A new polymeric adsorbent material based on polyethylene (PE) was prepared by photografting of 2‐(dimethylamino)ethyl methacrylate (DMAEMA) as a positively chargeable monomer to a PE film. The effects of the experimental parameters, such as the pH value, temperature, and grafted amount on adsorption of chromium(VI) (Cr(VI)) ions were investigated for the DMAEMA‐grafted PE (PE‐g‐PDAMEMA) films. The maximum adsorption capacity was obtained at the initial pH value of 3.0 for a PE‐g‐PDMAEMA film with 1.8 mmol/g and the maximum adsorption capacity obtained was higher than or compatible to those of many of the other polymeric adsorbents prepared for Cr(VI) ions. The adsorption kinetics obeyed the mechanism of the pseudo‐second order kinetic model and adsorption of Cr(VI) ions on PE‐g‐PDMAEMA films was well expressed by the Langmuir isotherm model. A high Langmuir adsorption constant suggests that the adsorption of Cr(VI) ions occurs between protonated dimethylamino groups and ions mainly through the electrostatic interaction. Cr(VI) ions adsorbed were successfully desorbed from a PE‐g‐PDMAEMA film in solutions of NaCl, NH₄Cl, NH₄Cl containing NaOH, and NaOH and a PE‐g‐PDMAEMA film was regenerated and repeatedly used for adsorption of Cr(VI) ions without appreciable loss in the adsorption capacity. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43360.     

Thermal transients during processing of materials by very high power ultrasonic additive manufacturing

Dynamic recrystallisation at interfaces has been suggested as the bonding mechanism in the joining of metallic tapes, during very high power ultrasonic additive manufacturing. To understand the reasons for such occurrence of dynamic recrystallization, thermal transients from the interface regions were recorded during processing of aluminum alloy (3003 and 6061 series) and 11 000 copper tapes under similar conditions. Measurements in 3003 Al were also carried out for different processing parameters. Measured peak temperatures were seen to increase with increase in shear strength of the material and ultrasonic vibration amplitude. The observations have been rationalized based on interfacial heating at asperities due to adiabatic plastic deformation.     

Growth of bubbles containing plasma in water by high-frequency irradiation

Plasma was generated in water by irradiation at high frequency of 13.56 MHz, and the behavior of bubbles including the plasma was observed by a high-speed camera. The generation pattern of the bubbles was classified into four types according to liquid temperature and supplied power. Conducting the simulation, the maximum temperature in the bubble was found to be from 3500 K to 4300 K, and the decomposition of water molecule occurred. The gas in the bubble was found to become high ratio of hydrogen. The phenomenon can be regarded as a film boiling of exceptionally high heat flux.     

An immuno-wall microdevice exhibits rapid and sensitive detection of IDH1-R132H mutation specific to grade II and III gliomas

World Health Organization grade II and III gliomas most frequently occur in the central nervous system (CNS) in adults. Gliomas are not circumscribed; tumor edges are irregular and consist of tumor cells, normal brain tissue, and hyperplastic reactive glial cells. Therefore, the tumors are not fully resectable, resulting in recurrence, malignant progression, and eventual death. Approximately 69–80% of grade II and III gliomas harbor mutations in the isocitrate dehydrogenase 1 gene (IDH1), of which 83–90% are found to be the IDH1-R132H mutation. Detection of the IDH1-R132H mutation should help in the differential diagnosis of grade II and III gliomas from other types of CNS tumors and help determine the boundary between the tumor and normal brain tissue. In this study, we established a highly sensitive antibody-based device, referred to as the immuno-wall, to detect the IDH1-R132H mutation in gliomas. The immuno-wall causes an immunoreaction in microchannels fabricated using a photo-polymerizing polymer. This microdevice enables the analysis of the IDH1 status with a small sample within 15 min with substantially high sensitivity. Our results suggested that 10% content of the IDH1-R132H mutation in a sample of 0.33 μl volume, with 500 ng protein, or from 500 cells is theoretically sufficient for the analysis. The immuno-wall device will enable the rapid and highly sensitive detection of the IDH1-R132H mutation in routine clinical practice.     

A mass separation of chondrocytes from cartilage tissue utilizing an automatic crushing device

Porcine articular cartilage tissue was crushed using Multi-Beads-Shocker^™ and digested with trypsin and collagenase type II. Chondrocyte cell yield was maximized by automatic crushing for 10 s, which was 4 times that by manual dicing with a surgical blade and might be useful for the automation of the cell processing.