膨胀石墨对各种油类的吸附动力学

通过对吸附率(有效吸附系数)Ks和饱和吸附量msat的测量,描述了粘度为0.001 Pa·s～0.850 Pa·s的各种油类在膨胀石墨柱中的吸附动力学,发现吸附率Ks对油类粘度有很强的相关性.吸入膨胀石墨柱中的饱和吸附量msat几乎恒定在50kg/kg,该值略低于由膨胀石墨块直接浸渍在油中测得的吸附容量,这是由于所吸附的油沿膨胀石墨柱高度存在重力梯度.     

A new voltage control equipment using fuzzy inference

Power system control equipment needs higher sensitivity and operational reliability. Advanced voltage control equipment is needed for reducing the frequency of tap changes and improving the characteristics (the relationship between the actual voltage and reference voltage) of the voltage to meet today's power system requirements. However, these objectives are in a trade-off relationship. Studies of voltage control derived from a knowledge base suitable for electric power systems can satisfy these objectives using fuzzy inference. Compared with corresponding conventional equipment, the new equipment improved the deviation of 30 min average voltage of 30 percent. This paper describes the design concept of new voltage control equipment using fuzzy inference. In addition, field test results are described along with rules of fuzzy inference, membership functions, and the deviation of 30 min average voltage through detailed simulation.     

Design of nonlinear controllers for active vehicle suspension with state constraints

Design of active vehicle suspension has tradeoffs between three main performance metrics (passenger comfort, suspension deflection and road holding ability). It has been known that each performance can be achieved by H _∞ controller and they can be gathered by LPV (Linear Parameter Varying) method. However, because the suspension deflection limit was not explicitly considered, this limit may be exceeded. In this paper, the authors propose a “reference shaping“ based method in order to improve the control performance. In this approach, a “virtual reference” signal is imposed to the system such that the suspension deflection is kept small. The effectiveness of the approach is examined by numerical simulations. This work was presented in part at the 13th International Symposium on Artificial Life and Robotics, Oita, Japan, January 31–February 2, 2008     

Heat Generation in Multilayer Piezoelectric Actuators

Multilayer piezoelectric actuators when driven under high frequency, generate significant heat, which influences the reliability and other piezoelectric properties. In this paper, heat generation in various types of multilayer PZT-based actuators was studied. Experimental results showed that heat generation is mainly caused by ferroelectric hysteresis loss in the stress-free state. A simplified analytic method was established to evaluate the temperature rise, which is useful for the design of multilayer and other high-power actuators.     

Polarization-controlled single-mode VCSEL

Relative intensity noise (RIN) in a vertical-cavity surface-emitting laser (VCSEL) was greatly reduced through the use of polarization control to eliminate competition between two orthogonal polarization states by ensuring there was only one polarization state. Polarization was stable with optical feedback of up to 10%. Polarization control was achieved by inducing a small loss anisotropy in fundamental transversal mode VCSEL's. Anisotropic post structures, such as a rectangular post, an oblique post, or a zigzag-sidewall post, were found to be effective in creating loss anisotropy without serious degradation of other VCSEL characteristics such as light-output power or beam profile     

Multiobjective dynamic load-dispatching method for optimal operation of power systems

A new practical method is proposed which gives a quasi-optimal solution of the dynamic load-dispatching problem formulated by a multiconstraint multiobjective optimization problem. Here, the multiple constraints are rate reserve constraints and power flow ones, and the multiple objectives are fuel cost and CO₂ emission. The proposed method is an integration of the following three techniques: (1) “Group Dispatch Scheme,” which is developed by the authors, is used to satisfy a violated constraint easily. This scheme consists of three steps. The first step is to classify all generators into two groups. One is the group which should be more loaded to satisfy the violated constraint, and the other is the should-be less loaded group. The second step is to add some load to the former group, and to subtract the same load from the latter. The third step is to dispatch each group load to each groups generators, respectively; (2) the dynamic load-dispatching algorithm is used which provides, in practical time, quasi-optimal generation trajectories; (3) the conventional weighting parametric method is used to obtain a Pareto optimal solution of multiobjective problems. The effectiveness of the method is clarified by a computer simulation on the actual power system of Kansai Electric Power Company.     

Effects of electrode arrangement and pressure on synthesis of diamond films by arc discharge plasma jet chemical vapor deposition

The setup and deposition conditions of electrode arrangement and pressure have been studied to synthesize diamond films at high growth rate on wide area efficiently by arc discharge plasma jet chemical vapor deposition. An apparatus has been used in which four plasma torches, one is used for cathode and the others for divided anodes, are arranged and the positions of these torches are changeable. Growth rate, deposition area and thickness of diamond films have increased with changing the electrode arrangements without improvement of thickness variation. Maximum growth rate of our apparatus has occurred at the pressure of 6.7 kPa and diamond films that have less variations of quality and surface roughness have been synthesized at lower pressure during deposition. Moreover, a high conversion rate, which is the ratio of carbon atoms that form diamond in supplied methane gas, of 16% has been obtained at the pressure of 6.7 kPa and methane concentration of 2%.     

Design of pseudo-ternary and quaternary alloys by superlattices consisting of (zn,cd)(s,se) binary ii–vi compounds

Theoretical design of pseudo-ternary and quaternary alloys by superlattice structures consisting of (Zn,Cd)(S,Se) binary II–VI compounds has been studied. For pseudo-ternary ZnCdS and ZnCdSe alloys, the superlattices with two layers in a cycle, i.e., ZnS/CdS and ZnSe/CdSe are considered, and for pseudo-quaternary ZnCdSSe alloy, the two superlattice structures with more than two layers in a cycle are considered. In order to design and evaluate these superlattices, the expression for the equilibrium in-plane lattice constant of these superlattices has been derived by minimizing the total elastic strain energy in the cycle. The combinations of layer thicknesses in a cycle and the effective bandgap of these superlattices have been calculated while the elastic strain effect was included. The usefulness of these superlattice structures has been evaluated.     

Nonlinear repetitive control with application to trajectory control of manipulators

In this article, a new control scheme named repetitive control is proposed for a class of nonlinear systems described by x(t) = Ax(t) + Bu(t) + n(x(t)) and y(t) = Cx(t), in which the controlled variables follow periodic reference commands. The stability condition is derived by applying the passivity theorem. We show how to apply the repetitive control scheme to the trajectory control of a manipulator. A simple repetitive control scheme is developed for the trajectory control of a manipulator by using nonlinear compensation and feedbacks of position and velocity signals. Experimental results for a three link manipulator verify that the proposed repetitive control reduces the tracking error to a very low level.     

Co-crosslinking blend of incompatible polymers VI: Poly(vinyl chloride) toughened with polyethylene via a co-crosslinking technique

A binary blend which consists of two incompatible polymers such as poly(vinyl chloride) and polyethylene has been performed through a partial co-crosslinking reaction with peroxide to give a co-crosslinked blend with a uniform dispersion of small polyethylene particles and with an improved mechanical property. The results are obtained through the formation of a co-crosslinked product which acts as a potential solid phase dispersant as well as a well-bonded reinforcing interlayer on polyethylene particles uniformly dispersed in poly(vinyl chloride) matrix. The resulting blends (PVC/PE=10/90 wt) give carbon spherules of 0.5 to 1m diameter through pressure-carbonization at 650° C for 1 h.