Impulse breakdown voltages of triggered multistage vacuum gap

Several sealed-off triggered vacuum gaps are connected in series to improve hold-off voltage. The characteristics of impulse breakdown voltage of these series-connected gaps are investigated experimentally. The sum hold-off voltage of series-connected gaps decreases to a unit hold-off voltage when the maximum value of voltage division ratio across the gaps increases to unity. Self-breakdown probability of the series-connected gaps is always higher than that of a single gap under the same conditions. Hence, stage efficiency of the multistage gap decreases with increasing number of stages. Its value is 90 percent with 2-stage gap and 75 percent with 5-stage gap, respectively, under the same voltage division ratio and the same gap length (2.0 mm) in each stage. Triggered breakdown voltage of 2- or 3- stage gap is several hundred volts when all gaps are triggered simultaneously at the peak of the main impulse wave and a working voltage range is nearly 100 percent in this case. The working voltage range decreases with number of stages. Its value is 45 percent with 3-stage gap and 15 percent with 5-stage gap, respectively, when one triggered gap is fired for switching.     

Thermoelastic solutions for orthotropic and anisotropic composite laminates

Solutions, within the framework of linear uncoupled thermoelasticity, are presented for certain problems of flexure of composite laminates. Benchmark numerical results, useful for the validation or otherwise of approximate laminate models, are tabulated. Finally, these results are used to examine the accuracy of the classical lamination theory based on Kirchhoff's hypothesis.     

Zooplankton population in the river tigris: Effects of samarra impoundment

The influences of the Samarra impoundment on the ecology of the downstream sector of the river Tigris are investigated. Zooplankton were collected monthly from July 1987 to July 1988. It was found that zooplankton were most abundant during high river discharges in March. During the month of low river discharge, September, the zooplankton population was greatly reduced immediately below the barrage and remained so to the last downstream station. Several factors seem to explain such differences. The high discharge from the impoundment was found to be the dominating factor and may flush the small backwaters in which zooplankton were abundant, thus increasing the population in the river. Zooplankton species vary in their ability to sustain populations in the river, variations which are due mainly to species-specific characteristics.     

A New Image Analysis Based Method for Measuring Electrospun Nanofiber Diameter

In this paper, a new image analysis based method for electrospun nanofiber diameter measurement has been presented. The method was tested by a simulated image with known characteristics and a real web. Mean (M) and standard deviation (STD) of fiber diameter obtained using this method for the simulated image were 15.02 and 4.80 pixels respectively, compared to the true values of 15.35 and 4.47 pixels. For the real web, applying the method resulted in M and STD of 324 and 50.4 nm which are extremely close to the values of 319 and 42 nm obtained using manual method. The results show that this approach is successful in making fast, accurate automated measurements of electrospun fiber diameters.     

Effects of molybdenum additions on the structure, depth, and austenite grain size of the case of carburized 0.13% carbon steels

Carbon (0.13%) steel samples containing about 0.48% molybdenum (Mo) singly and in combination with nickel (Ni) were carburized in a natural Titas gas atmosphere at a temperature of 1223 K (950 °C) and at a pressure of about 0.10 MPa (15 psia) for time periods ranging from 1–4 h followed by slow cooling in the furnace. Their microstructure was studied by optical microscopy. The austenite grain size of the case and the case depths were determined. It was found that Mo and Ni alone and in combination decrease the thickness of the cementite network near the surface of the carburized case of the steels. However, Ni is found to be more effective than Mo in decreasing the thickness of cementite network. Both Mo and Ni enhance the formation of Widmanstätten cementite plates at the grain boundary and within the grains near the surface of the carburized steels. However, Ni alone is more effective than Mo in the formation of Widmanstätten cementite plates. In the presence of Ni, Mo is much more effective in the formation of Widmanstätten cementite plates than Mo in absence of Ni. It was also revealed that both Mo and Ni increased the case depth. Ni is more effective than Mo in increasing the case depth. The combined effect of Mo and Ni is much greater than that of either Mo or Ni alone in increasing case depth. Mo as Mo carbide (Mo₂C) particles refined the austenite grain size of the carburized case. Ni in solution was not found to have any effect in restricting grain growth of austenite, but the presence of Ni enhances the austenite grain size refining effect of Mo in the carburized case.     

Capacity planning in job-shop environment

Presented here is a computerized capacity planning system for the IBM Microcomputer family. The system maintains the profile of the job shop in a data base along with data pertinent to various products that can be manufactured in the shop. Projected orders for the planning period are input to the system with their associated quantities and delivery dates. The system uses the forward and backward loading rules in generating capacity loading scenarios. User selects the best course of action which may satisfy delivery dates subject to the limitations of the work centers. Efficiency figures are provided to aid the user in his/her decision.     

Framework Model for Asset Maintenance Management

This paper presents the development of a generic framework for asset maintenance management. The framework has been presented in the form of an IDEF0 process model. The process model served to illustrate the interaction and dependencies among a diverse set of knowledge areas. In this framework, outputs from one management process become inputs to another in a subsequent hierarchy. The structure of the framework model exhibited the characteristics of flexibility and robustness. Updates in knowledge can be accommodated within the framework through incorporating new management processes and/or activities, as well as establishing new sequencing logic for these processes and/or activities. In a supporting effort to the development of the framework model, the writers have objectively reviewed the general capabilities of three commercially available software applications that are known within the asset management (AM) industry. These three applications, while encompassing a wide selection of capabilities, represent a typical selection of information technology (IT) tools and techniques that are widely used in strategic AM practices. The objective of this review is to study the operational characteristics and functionalities, and to assess the capability of software interoperability, of a representative sample of IT tools known within the AM industry.