A comparative study on oxidation of disperse dyes by electrochemical process, ozone, hypochlorite and Fenton reagent

The results of an experimental study on the destruction of disperse dyes by chemical oxidation using ozone, hypochlorite and Fenton reagent (H2O2 + Fe2+) are compared with the data obtained by electrochemical oxidation. While the results obtained during hypochlorite oxidation were not satisfactory (only 35% reduction of colour was achieved at a dose of 6 g dm(-3)), ozonation enabled colour to be reduced by up to 90% (ozone dose 0.5 g dm(-3)). A high decolourisation degree was however accompanied by a low removal (10% efficiency) of chemical oxygen demand (COD). Trials of electrochemical oxidation proved this process much more efficient. Under the conditions of an acidic pH in 40 min of electrolysis a 79% elimination of COD was achieved at the Ti/Pt-Ir anode, which proved the best of seven different tested materials. Simultaneously 90% colour was removed. Indirect oxidation, by means of chlorine-deriving compounds, was the predominating process leading to the pollutants depletion. The best treatment results were obtained with the Fenton process, which under the optimal pH equal to 3 and hydrogen peroxide and ferrous sulphide dose of 600 and 550 mg dm(-3), respectively, resulted in a final effluent being colourless and with the residual COD equal to 100 mg dm(-3).     

Surfactant assisted synthesis and spectroscopic characterization of selenium nanoparticles in ambient conditions

In this work, an attempt has been made to synthesize well-distributed stable selenium (Se) particles of nanosize dimensions via an aqueous micellar solution by the assistance of surfactants of two different polarities (anionic, sodium bis(2-ethylhexyl)sulfosuccinate (AOT) and cationic, hexadecyltrimethylammonium bromide (CTAB)). The morphology of the particles was examined with transmission electron microscopy (TEM). X-ray analysis reveals that the particles have a monoclinic structure. The band gap of the particles was determined from UV-visible optical spectroscopic results. The size variation was estimated by employing a quantum confinement effect equation. The evolution of the selenium nanoparticles in AOT and CTAB micellar media was corroborated with the time-dependent absorption spectra. The influence of hydrazine hydrate concentrations on the formation kinetics of Se nanoparticles was also investigated. The capping ability of the surfactants has been quantitatively evaluated from Fourier transform infrared (FTIR) studies.     

Size and surface effects on the MRI relaxivity of manganese ferrite nanoparticle contrast agents

Superparamagnetic MnFe2O4 nanocrystals of different sizes were synthesized in high-boiling ether solvent and transferred into water using three different approaches. First, we applied a ligand exchange in order to form a water soluble polymer shell. Second, the particles were embedded into an amphiphilic polymer shell. Third, the nanoparticles were embedded into large micelles formed by lipids. Although all approaches lead to effective negative contrast enhancement, we observed significant differences concerning the magnitude of this effect. The transverse relaxivity, in particular r2*, is greatly higher for the micellar system compared to the polymer-coated particles using same-sized nanoparticles. We also observed an increase in transverse relaxivities with increasing particle size for the polymer-coated nanocrystals. The results are qualitatively compared with theoretical models describing the dependence of relaxivity on the size of magnetic spheres.     

Routing Protocols in Delay Tolerant Networks: Comparative and Empirical Analysis

Wireless Personal Communications - A Delay Tolerant Network (DTN) is a network capable of handling long delays and data loss efficiently in various challenged scenarios and environments. Owing to...     

Electromechanical carbon nanotube switches for high-frequency applications

We describe the fabrication and characterization of a nanoelectromechanical (NEM) switch based on carbon nanotubes. Our NEM structure consists of single-walled nanotubes (SWNTs) suspended over shallow trenches in a SiO(2) layer, with a Nb pull electrode beneath. The nanotube growth is done on-chip using a patterned Fe catalyst and a methane chemical vapor deposition (CVD) process at 850 degrees C. Electrical measurements of these devices show well-defined ON and OFF states as a dc bias up to a few volts is applied between the CNT and the Nb pull electrode. The CNT switches were measured to have speeds that are 3 orders of magnitude higher than MEMS-based electrostatically driven switches, with switching times down to a few nanoseconds, while at the same time requiring pull voltages less than 5 V.     

Magnesium and iron nanoparticles production using microorganisms and various salts

Response of five fungi and two bacteria to different salts of magnesium and iron for production of nanoparticles was studied. Pochonia chlamydosporium, and Aspergillus fumigatus were exposed to three salts of magnesium while Curvularia lunata, Chaetomium globosum, A. fumigatus, A. wentii and the bacteria Alcaligenes faecalis and Bacillus coagulans were exposed to two salts of iron for nanoparticle production. The results revealed that P. chlamydosporium induces development of extracellular nanoparticles in MgCl₂ solution while A. fumigatus produces also intracellular nanoparticles when exposed to MgSO₄ solution. C. globosum was found as the most effective in producing nanoparticles when exposed to Fe₂O₃ solution. The FTIR analysis of the nanoparticles obtained from Fe₂O₃ solution showed the peaks similar to iron (Fe). In general, the species of the tested microbes were selective to different chemicals in their response for synthesis of nanoparticles. Further studies on their characterization and improving the efficiency of promising species of fungi need to be undertaken before tapping their potential as nanonutrients for plants.     

Efficacy of continuous wear PureVision contact lenses for therapeutic use.

PURPOSE: To evaluate the Bausch and Lomb PureVision contact lens as continuous wear contact lens for therapeutic and medical indications in a prospective open-ended non-randomized trial. METHODS: Patients who required therapeutic contact lens wear for various indications such as pain relief, corneal protection, persistent epithelial defects, corneal perforation and chemical burns were fitted with PureVision continuous wear contact lenses (balafilcon A, 36% water content). Success or failure of specific treatment indication was assessed in each case with evaluation of ocular and lens related complications. RESULTS: 30 eyes of 28 patients were fitted with PureVision continuous wear contact lenses. A successful fit was seen in 27 of 30 eyes with therapeutic success in 26 of 30 eyes. However, all patients reported symptomatic relief. Duration of lens use ranged from 3 days to 3 months. Dry eye was the most frequent cause of contact lens associated therapeutic failure. Complications included lens loss (two eyes), tight lens (one eye) and infective keratitis (two eyes). CONCLUSIONS: PureVision contact lenses were found to be safe and efficacious for continuous wear therapeutic use to a maximum of 90 days. The contact lens was also easier to handle by virtue of its resilient nature. There were no significant corneal complications of hypoxia, i.e. corneal oedema. Lens losses and deposits were minimal. The lens performance and fitting characteristics compares favorably with previous therapeutic lenses used by the investigators. This new lens may be considered as a safe and effective alternative for use as bandage contact lens.     

Effect of low frequency ultrasonic assisted extraction on the quality of seed oils of Indian origin

The study gives an insight into the effect of low frequency ultrasonic enhancement of solvent extraction on the quality of non-edible oils (Jatropha and Pongamia as model seed varieties) in comparison to conventional methods of extraction i.e. direct reflux or soxhlet extraction using hexane. A series of experiments have been carried out to study the effect of variables; solute to solvent ratio (1:2.5-1:10) and reaction time (30 s-60 min) on the yield of oil. The quality of oil extracted by different methods have been assessed by determining the acid value of oil by ASTM D-974/04 method, a measurement of triglyceride and fatty acid degradation, by the presence of phorbol esters in Jatropha curcas and phenolic compounds in Pongamia oil analyzed using HPLC. Under optimized conditions solute to solvent ratio of 1:10 (w/v), 3 min extraction time yields > 95% pure oil having < 1% FFA in Jatropha curcas and 30 s extraction time in Pongamia seed yields oil with less than 2% FFA in comparison to conventional method of extraction in 16 h.