单晶钛酸铋纳米片的XPS和Raman特性

以Bi（NO3）3·5H2O和Ti（OC4H9）4为原料，NaOH为矿化剂，采用水热法制备了形貌规则的单晶Bi4Ti3O12纳米片。X射线衍射（XRD）结果表明，所合成的产物为正交相层状钙钛矿结构的Bi4Ti3O12。场发射扫描电子显微镜（FESEM）研究显示：样品是由大量边缘尺寸接近200nm，厚度约为15nm的片状结构组成。利用X射线光电子能谱（XPS）研究产物的化学组分和价态分布。室温拉曼光谱研究表明，Bi4Ti3O12纳米片的声子寿命和热稳定性低于相应的块体材料。     

Influence of phosphorus element on direct laser sintering of multicomponent Cu-based metal powder

This article presents a detailed investigation on the influence of the phosphorus element upon the laser sintering of a multicomponent Cu-based metal powder system consisting of Cu, Cu-10Sn, and Cu-8.4P. Powder systems containing 0, 10, 15, and 20 wt pct CuP were sintered in atmosphere at room temperature using the following optimal processing parameters: laser power of 350 W, scan speed of 0.04 m/s, scan line spacing of 0.15 mm, and layer thickness of 0.25 mm. It was found that the relative density of the sintered sample with 15 wt pct CuP increased by 24,4 pct as compared with the sample without phosphorus addition. A further increase in the CuP content (≥20 wt pct), however, resulted in a poor densification with a serious delamination. The exact metallurgical roles of the phosphorus element in the laser sintering process were addressed as follows. First, the phosphorus could prevent the sintering system from oxidation by forming CuPO₃, thereby improving the wetting characteristics and the sintering kinetics. Second, the phosphorus could decrease the surface tension of molten materials, leading to a successive transition from highly discontinuous sintered tracks to fairly coherent ones with increasing the phosphorus content. Third, the phosphorus could lower the melt viscosity, thereby improving the microstructural homogeneity of the laser-sintered samples.     

Pattern search algorithms for nonlinear inversion of high-frequency Rayleigh-wave dispersion curves

Inversion of Rayleigh wave dispersion curves is challenging for most local-search methods due to its high nonlinearity and to its multimodality. In this paper, we implemented and tested a Rayleigh wave dispersion curve inversion scheme based on GPS Positive Basis 2N, a commonly used pattern search algorithm. Incorporating complete poll and complete search strategies based on GPS Positive Basis 2N into the inverse procedure greatly enhances the performance of pattern search algorithms because the two steps can effectively locate the promising areas in the solution space containing the global minima and significantly reduce the computation cost, respectively.The proposed inverse procedure was applied to nonlinear inversion of fundamental-mode Rayleigh wave dispersion curves for a near-surface shear (S)-wave velocity profile. The calculation efficiency and stability of the inversion scheme are tested on three synthetic models and a real example from a roadbed survey in Henan, China. Effects of the number of data points, the reduction of the frequency range of the considered dispersion curve, errors in P-wave velocities and density, the initial S-wave velocity profile as well as the number of layers and their thicknesses on inversion results are also investigated in the present study to further evaluate the performance of the proposed approach.Results demonstrate that pattern search algorithms applied to nonlinear inversion of high-frequency surface wave data should be considered good not only in terms of accuracy but also in terms of the computation effort due to their global and deterministic search process.     

拉伸试验测量不确定度的研究

分析了拉伸试验中抗拉强度Rm的影响因素，对测量不确定度的主要分量进行量化，评定了Rm的相对测量不确定度，作为生产检验中评定测量不确定度的尝试，以便为用户提供钢材性能测量结果的不确定度。     

Preparation of Compound Ultrafine CeO2 by Wet-Solid-Phase Mechanochemical Modification

To satisfy practical requirements from industrial applications, an alternate route for synthesis compound ultrafine CeO2 powders by wet-solid-phase mechanochemical modification using industrial grade hydrated cerium carbonate as raw material was proposed.The effect of modifier reaction percentage, reaction time, calcining temperature and modifier amount on particle size, density, suspensibility, and hardness of compound CeO2 powder was investigated.The phase evolutions of preparation process were characterized by XRD.SEM micrograph of the final product shows that compound CeO2 powders obtained are well-dispersed, spherically-shaped, uniformly-sized and submicron-sized particles.The method is readily available in raw material, low in cost, simple in process, and has great potential for industrialization.The compound CeO2 powders of different physical properties can be synthesized by controlling the above-mentioned influence factors in preparation process.     

球式热风炉球床结构的热工讨论

球式热风炉作为低成本，高效率的冶金炉已被越来越多的钢铁企业所采用，广钢新3号高炉首次采用球式热风炉，炉子的球床结构，球径大小，材质的选择都将对球式热风炉的热工性能产生重要的影响。本文主要从热工理论方面探讨了球床结构的合理性。     

应用杜邦财务分析体系对企业进行绩效评价

随着我国企业经营机制的不断完善,企业內部经营管理水平不断提升,越来越要求企业重视财务分析。通过对杜邦财务分析体系的介绍,结合实例应用杜邦财务分析体系对企业进行绩效评价,意在对各企业正确应用杜邦财务分析体系,揭示在经营目标发生异动时查明原因,并为企业采取措施修正指标指明方向。     

Measured equation of invariance with linear tensor relation for three-dimensional scattering problems

The postulate of a linear tensor relation in the measured equation of invariance (MEI) is proposed for three-dimensional (3D) problems. As a result, all three components of the field vector to be solved are coupled in the MEI. Combined with the finite difference method, the present method is applied to the analysis of scattering by 3D conducting objects and results in a significant improvement in the accuracy of numerical results as compared to those obtained with an uncoupled linear relation.     

多粒度全光网中的多层联合路由

多粒度交换技术利用波带级路由以及光纤级路由,可有效降低光交叉连接器的复杂度.但多粒度交换增加了光网络的逻辑层次结构,使得网络中的路由与资源分配问题更为复杂,因此,在多粒度全光网中实现多层联合路由是提高网络性能的关键.本文对多粒度交叉连接结构进行了分析,并对多粒度全光网中的多层联合路由问题进行了研究.     

Effect of thermal treatment on ZnO substrate for epitaxial growth

ZnO is a highly efficient photon emitter, and has optical and piezoelectric properties that are attractive for a variety of applications in sensors and potentially optoelectronic devices such as emitters. Due to its identical stacking order and close lattice match to GaN, it is also being developed as a substrate material for GaN epitaxy. However, the surface finish of the ZnO is such that much of the damage induced by sawing and follow up mechanical polishing remains. We developed a thermal treatment method to eliminate surface damage on the 0 face of ZnO (0 0 0 1) to prepare it for epitaxial growth. Atomic force microscopy images of ZnO (0 0 0 1) annealed at 1050 °C for 3 h etc. show that residual scratches from mechanical polishing are removed and atomically flat, terrace-like surfaces are attained. In addition, low-temperature photoluminescence and high-resolution X-ray diffraction measurements have been employed to investigate the effect of annealing on ZnO substrates.