Effect of Microstructure on the Accelerated Creep of 20CrMoV12‐1 and P 91 Steels

In the initial part the change of microstructure for steel X20 CrMoV 121 is discussed in terms of the distribution of carbide precipitates and its effects on accelerated creep resistance and hardness are presented. In the following, experimental results of microstructure and accelerated creep resistance are presented for the steels X20CrMoV 121 and P91 annealed for up to 8760 hours at 650°C and 750°C before the testing. A similar evolution of the distribution of carbide particles of a size above 102 nm is found for both steels, while the accelerated creep resistance is diminished much stronger for the steel X20CrMoV 121. This difference is due to a greater stability of NbC than that of VC precipitates, both related to the evolution of the chemical composition of complex chromium, molybdenum and iron carbide particles.     

Correlation between magnetic hysteresis and magnetic relaxation in YBaCuO single crystals

The dependence of the magnetic momentm obtained from the hysteresis loops on the speed of the magnetic field sweep =dH _ext/dt is explained on the basis of Anderson's interpretation of the magnetic flux creep. In addition, a phenomenological model is suggested which predicts a linear dependence ofm on ln with the slope m/ ln , numerically equal to the relaxation rate m/ ln(t) from the usual magnetic relaxation. Such linear relations betweenm and ln were observed experimentally in single crystals of YBaCuO. Preliminary experiments on the complementary time dependent relaxation ofm after a simulated step change ofH _ext gave mostly relaxation rates close to the predicted values. The model here presented also enables one to compare the critical state in the superconductor at a field sweep rate with the critical state at some timet _eff after a step change ofH _ext. The values of analyzed in our experiments actually correspond to the critical state at timest _eff between0.04 and4 sec after an imaginary large step change ofH _ext.     

A study of Nd2Fe14B and a neodymium-rich phase in sintered NdFeB magnets

The microstructure and properties of NdFeB sintered permanent magnets were analysed by different methods. Samples analysed were sintered and thermally treated. The hard magnetic Nd₂Fe₁₄B phase and amorphous neodymium-rich phase were observed by TEM. The neodymium-rich phase contained iron and boron, in elemental and in B₂O₃ form, which is known as a glass former. At the sintering temperature, Nd₂Fe₁₄B and the neodymium-rich phase are supersaturated with iron, which should be dissolved at the annealing temperature to react with neodymium and boron and form additional Nd₂Fe₁₄B phase. Iron precipitates of size up to 2 nm were detected in the Nd₂Fe₁₄B phase. These superparamagnetic precipitates of -Fe could affect the hard magnetic properties of NdFeB magnets.     

Local Binary Pattern based features for sign language recognition

In this paper we focus on appearance features particularly the Local Binary Patterns describing the manual component of Sign Language. We compare the performance of these features with geometric moments describing the trajectory and shape of hands. Since the non-manual component is also very important for sign recognition we localize facial landmarks via Active Shape Model combined with Landmark detector that increases the robustness of model fitting. We test the recognition performance of individual features and their combinations on a database consisting of 11 signers and 23 signs with several repetitions. Local Binary Patterns outperform the geometric moments. When the features are combined we achieve a recognition rate up to 99.75% for signer dependent tests and 57.54% for signer independent tests.     

Carcass traits and meat quality of male lambs fed monensin or lasalocid

Male lambs, crossbred Merino × Ille de France, were fed a diet supplemented with 31 mg monensin or 32 mg lasalocid per kg of feed dry matter from an initial body weight of 23·6–23·9 kg to the slaughter weight of approximately 40 kg.

Carcass traits and meat quality were evaluated after slaughter; the values obtained were compared with those of the control group fed the same diet without the ionophore supplement.

There were few significant differences among the individual groups in carcass value, sensoric and technological properties of meat and of its composition. However, the lasalocid-fed group seemed to be somewhat better in muscling and in the composition of meat.     

Isobutylene polymerization in the presence of t-BuCl/SnCl4

Summary The effect of tert-butyl chloride in the polymerizations of isobutylene carried out in the presence of SnCl₄ in dichloromethane at temperatures-20°C and-78°C was investigated. Synthesized polyisobutylene samples showed a bimodal molecular weight distribution (MWD) and it was found that the weight content of the lowermolecular weight (LMW) fraction increased with increasing t-BuCl concentration in the polymerization mixture. The effect of ageing of the initiation mixture t-BuCl/SnCl₄ in CH₂Cl₂ prepared in advance on MWD of the PIB samples was also studied. Ageing of the initiation system supports the formation of the LMW fraction and this oily PIB is the only product of the polymerization at-20°C, .     

Fault-Tolerant Formation Driving Mechanism Designed for Heterogeneous MAVs-UGVs Groups

A fault-tolerant method for stabilization and navigation of 3D heterogeneous formations is proposed in this paper. The presented Model Predictive Control (MPC) based approach enables to deploy compact formations of closely cooperating autonomous aerial and ground robots in surveillance scenarios without the necessity of a precise external localization. Instead, the proposed method relies on a top-view visual relative localization provided by the micro aerial vehicles flying above the ground robots and on a simple yet stable visual based navigation using images from an onboard monocular camera. The MPC based schema together with a fault detection and recovery mechanism provide a robust solution applicable in complex environments with static and dynamic obstacles. The core of the proposed leader-follower based formation driving method consists in a representation of the entire 3D formation as a convex hull projected along a desired path that has to be followed by the group. Such an approach provides non-collision solution and respects requirements of the direct visibility between the team members. The uninterrupted visibility is crucial for the employed top-view localization and therefore for the stabilization of the group. The proposed formation driving method and the fault recovery mechanisms are verified by simulations and hardware experiments presented in the paper.     

Experimental observation of temperature gradients occurring in a single zeolite pellet

An experimental study has been made of temperature profiles incident within a zeolite adsorbent particle in the course of adsorption of n-heptan. Using thermocouple wires 0.1 mm in diameter it has been possible to measure simultaneously the temperatures of the surface and in the centre. It was observed that temperature differences between center of the pellet and ambient stagnant gas may be more than 20°C. The results of this work indicate that the overheating of an adsorbent particle is a very rapid process which is followed by a slow cooling of the hot particle. Experimental data are compared with predictions calculated from the theoretical model.     

Solvent induced crystallization of syndiotactic poly(methyl methacrylate) relation to the formation of polymer aggregates in solution

Polymer Bulletin - Solutions of syndiotactic (s) poly (methyl methacrylate) (PMMA) and samples of solid s-PMMA prepared from these solutions were studied by NMR and infrared (IR) spectroscopy and...