Improvement of dielectric breakdown strength and energy storage performance in Er2O3–modified 0.95Sr0.7Ba0.3Nb2O6-0.05CaTiO3 lead-free ceramics

In this study, 0.95?Sr_0.7Ba_0.3Nb₂O₆-0.05CaTiO₃-x wt% Er₂O₃ ceramics (SBNCTEx; x?=?0–5) were synthesized using traditional solid-state method, and we investigated the microstructure, energy storage properties as well as the relationship between dielectric breakdown strength and interfacial polarization. As compared with pure 0.95?Sr_0.7Ba_0.3Nb₂O₆-0.05CaTiO₃ ceramics, the Er₂O₃ dopants suppressed the grain growth of SBNCTEx, and the doped ones showed the dense microstructure. The secondary phase was found for x?≥?1 according to the EDS results, and the influence of the secondary phase on relative dielectric breakdown strength has also been studied. The dielectric breakdown strength increased from 18.1?kV/mm to 34.4?kV/mm, which is good for energy storage. The energy storage density of 0.28?J/cm³ and the energy storage efficiency of 91.4% were obtained in the SBNCTE5 ceramics. The results indicate that SBNCTE ceramics can be used as energy storage capacitors.     

A new perspective of co-doping and Nd segregation effect on proton stability and transportation in Y and Nd co-doped BaCeO3

Bulk and surface properties of proton stability and transportation in Y and Nd co-doped BaCeO₃ (BCYN), especially the effect of Nd segregation, were investigated by first-principles calculations. Since the structure of doped BaCeO₃ at the operating temperature of proton-conducting has been unclear for a long time, we have summarized the latest experimental results and calculated the structure of the asymmetric BCYN for the first time. The results show that compared with Y, Nd doping promotes oxygen vacancy formation, however reduces proton stability. Our calculation can also provide a possible explanation for the formation of space charge layer at the grain boundary of doped BaCeO₃ in experiment. Unlike the stable Y in BCYN, Nd is calculated to be easily segregated, which can facilitate both proton hydration and proton transportation near the surface. Moreover, Nd segregation at the grain boundary is predicted to be beneficial for proton transportation between grains.     

电石冷却车间厂房通风模型的研究及应用

介绍了厂房通风模型在电石冷却车间改造中的应用,对比分析了改造前后冷却车间内的通风状态.模拟结果表明,冷却车间厂房内的总通风量增加了99.4％,通风温度降低了20.5 ℃,厂房结构和设备表面温度降低了50℃,能有效解决冷却车间内通风温度偏高的问题,提高电石转运率.根据通风模型进行改造后,电石冷却时间缩短25％,证明厂房通风模型准确可靠.     

含齿形裂隙类岩石材料单轴压缩试验研究

为研究含齿形裂隙岩石在单轴压缩下的破坏特征及强度特性，制作了含不同裂隙倾角和起伏角的齿形裂隙类岩石材料试件，并采用岩石力学伺服试验机进行单轴压缩试验。试验结果表明：（1）试件主要产生拉伸、剪切和拉剪复合裂纹，且根据裂纹的扩展路径可划分为A型（拉伸破坏）、B型（剪切破坏）、C型（复合破坏）3种破坏模式，裂隙倾角对试件最终破坏模式影响显著；（2）当裂隙倾角较小时，试件应力—应变曲线为多峰曲线，随着裂隙倾角的增大，曲线呈单峰形式，表现为延性减弱，脆性增强，而裂隙倾角相同但起伏角不同的试件应力—应变曲线大致相同；（3）当裂隙起伏角相同时，试件当量峰值强度随裂隙倾角的增大呈先减小后增大的规律，且裂隙起伏角对试件当量峰值强度的影响小于裂隙倾角。     

自然循环工况下离心泵阻力特性的实验研究与数值模拟

停转后泵的阻力特性对自然循环流量影响明显。为研究低流量自然循环工况下离心泵的阻力特性，设计了实验台架，对离心泵的正向压降、反向压降和损失系数进行了测量，实验雷诺数为2.0×10⁴～1.5×10⁵。实验表明：相同雷诺数下，反向压降明显高于正向压降；雷诺数大于8×10⁴时，损失系数基本保持不变，而低雷诺数下损失系数随雷诺数的降低有增大的趋势；基于实验得到了损失系数的经验关系式。采用CFD方法对离心泵的内部流场进行了模拟，计算表明：CFD方法能较好地预测损失系数，RNG k-ε模型与实验值的相对误差不超过10%；离心泵的压力损失主要集中在叶轮、导叶等结构的交界区域；正向与反向流动的流场分布存在显著区别；低雷诺数下局部流动更加不稳定。     

电喷雾质谱法示踪钨回收过程离子的转化路径

将环隙式离心萃取器(ACCs)与电喷雾飞行时间质谱(ESI-TOF-MS)相结合，在线监测了回收过程中的钨萃取行为(宏观)和钨形态的转化路径(微观)，发现宏观萃取反应和微观离子形态转化同时发生并相互补充。伯胺N1923萃取钨在144 s内即可达到萃取平衡，萃取率高达98%以上，同时，酸钨比n(H)/n(W)是一个关键变量，当酸钨比n(H)/n(W)=2.4时，全流程钨回收率超过93%。最后，得到了基于钨形态监测的萃取机理，同时，减少原料液中W1含量，增加W10含量，可有效提高钨回收效率。     

重力注水过程流动不稳定现象关键影响因素研究

重力驱动注水过程中由于流量较小以及蒸汽的积聚可能导致流动不稳定现象的发生，对核反应堆安全运行具有重要的影响。通过实验研究的方法，搭建了重力注水模拟实验装置，研究了不同蒸汽出口形阻、高位储水箱水位和加热棒初始温度下流动不稳定现象的变化规律。结果表明，重力驱动注水过程流动不稳定现象包含冷却水初次注入阶段、注入水逐出阶段和冷却水再注入阶段等。在一定冷却水初始温度、冷却水入口形阻以及系统压力下，蒸汽排出速度以及实验本体内筒顶部的聚集情况取决于蒸汽出口形阻，减小蒸汽出口形阻可加快蒸汽排放速度，压力峰峰值降低、振荡周期变长，有利于系统稳定；提高高位储水箱水位加快了冷却水注入速率，增加了加热棒被淹没率，降低了流动不稳定现象的发生次数和持续时间；随加热棒初始温度的升高，冷却水流量出现了波动向停滞的转变，流动不稳定现象发生的次数增加且持续时间加长。     

木片筛余物高得率半化学法清洁制浆技术研究

以太阳纸业备料车间木片筛选碎料（筛余物）为原料，对其烧碱法半化学制浆的实验室工艺和生产试验进行了研究。结果表明，筛余物采用半化学法制浆可获得较高得率和环压强度的纸浆，且用碱量对纸浆性能有显著影响。相对8%NaOH （相对于绝干原料）化学预处理，采用14%NaOH化学预处理结合两段浆浓22%的高浓磨浆工艺，所制半化学浆抄造浆张的裂断长和环压指数分别达2.89 km和9.76 N·m/g，是前者的1.9倍和1.2倍，而且优于现用国内OCC废纸浆抄造浆张；生产试验得到的浆张性能指标与实验室相吻合，其中紧度和环压强度分别达到GB/T 13023—2008瓦楞芯（原）纸AA级和A级优等品要求。