A comparative study on in vitro behavior of calcium silicate ceramics synthesized from biowaste resources

Calcium silicate ceramics have received significant attention for biomedical applications for their excellent bioactivity and osteoconduction properties. Sol-gel process is extensively used for the fabrication of calcium silicates. In sol-gel process, calcium nitrate tetra hydrate (Ca(NO₃)₂·4H₂O) and tetraethylorthosilicate (TEOS) are used as precursors. However, these precursors are expensive. The objective of this work was to compare in vitro behavior of calcium silicate (CaSiO₃) produced using biowaste such as rice husk ash (RHA) and eggshells (coded; NCS) with CaSiO₃ prepared using TEOS and Ca(NO₃)₂·4H₂O (coded; CCS). Thermal investigation results revealed that the crystallization temperature for NCS is relatively lower (772°C) than for CCS (870°C). Bioactivity was studied in vitro using simulated body fluid (SBF) with respect to mineralization rate of hydroxyapatite. Mineralization of a greater hydroxyapatite was observed on NCS ceramics than CCS ceramics after incubation for 3, 7, 14 days in SBF solution, which was confirmed using X-ray diffractometer, Fourier transform infrared spectroscopy, scanning electron microscopy-energy dispersive spectroscopy. Degradation studies were conducted in Tris-HCl solution and the test results revealed that NCS ceramics has lower dissolution rate than CCS ceramics. The antimicrobial assay has shown that NCS samples exhibit significant zone of inhibition against Escherichia coli and Staphylococcus aureus which confirmed that the CaSiO₃ prepared from RHA and eggshell can prevent bacteria from adhering to the surface. In addition cell culture studies revealed that NCS ceramics possess good cytocompatibility with MG-63 cells and significantly promoted cell proliferation.     

Transesterification of Palm-based Methyl Palmitate into Esteramine Catalyzed by Calcium Oxide Catalyst

The technology for transesterification reactions between methyl esters and alcohols is well established by using classical homogeneous alkaline catalysts, which provide high conversion of methyl esters to specialty or nonindigenous esters. However, in certain products where the purity of the esters is of concern, the removal of homogeneous catalysts after the completion of the reaction is a challenge in terms of production cost and water footprint. Therefore, a study to investigate the potential of heterogeneous catalysts was conducted on reactions between methyl palmitate and triethanolamine. The degree of basicity and active surface area of calcium oxide (CaO), zinc oxide (ZnO), and magnesium oxide (MgO) were first characterized by using temperature-programmed desorption (TPD-CO₂) and Brunauere–Emmett–Teller (BET), respectively. Among the metal oxides investigated, the CaO catalyst showed the best catalytic activity toward the transesterification process as it gave the highest conversion of methyl palmitate and yielded fatty esteramine compositions similar to the conventional homogeneous catalyst. The optimum transesterification condition by using the CaO catalyst utilized a lower vacuum system of approximately 200 mbar, which could minimize a considerable amount of energy consumption. Furthermore, low CaO dosage of 0.1% was able to give a conversion of 94.5% methyl ester and formed esteramine at 170 °C for 2 h. Therefore, the production of esterquats from esteramine may become more economically feasible through the methyl ester route by using the CaO catalyst, which can be recycled three times.     

Influence of Different Additives on the Interaction of Quinolone Antibiotic Drug with Surfactant: Conductivity and Cloud Point Measurement Study

Conductometric and cloud point (CP) measurement studies have been performed to investigate the interaction of tetradecyltrimethylammonium bromide (TTAB) and Triton® X-100 (TX-100) with ciprofloxacin hydrochloride (CFH) in different solvents over the temperature range of 295.15–315.15 K. CFH is used for the treatment of various bacterial infections. The observed critical micelle concentration (CMC) values of TTAB were found to be reduced in the presence of electrolytes (Na₂SO₄/Na₃PO₄), and this reduction proceeds with the elevation of salt concentration. The order of the CMC of TTAB follows the trend: > >. The observed CMC values of TTAB were found to increase with increasing temperature and decrease with increasing concentration of CFH in aqueous medium. The values of Gibbs free energy of micellization () for the TTAB/TTAB + CFH mixture were found to be negative, implying spontaneous micellization. The estimated CP of TX-100 decreases with increasing concentration of TX-100 in aqueous medium. The CP values first decrease with increasing concentration of CFH and then increase at higher concentration of CFH almost in all cases investigated. The values of free energy of clouding were found to be positive in all cases studied implying that phase separation of TX-100 was nonspontaneous. The other thermodynamic parameters associated with the micellization of TTAB and the phase separation of TX-100 were estimated and explained.     

Antimicrobial residues survey by LC-MS in food-producing animals in Lebanon

ABSTRACT

The treatment of animals with antimicrobial products may lead to the contamination of edible tissues by their residues, which may represent a risk to human health. Therefore, this study aimed to determine the level of antimicrobial residues in food-producing animals (chicken, beef, and milk) in Lebanon. A total of 310 samples were collected and analysed using an LC-MS/MS for the determination of 48 compounds belonging to different families in order to map their compliance according to the European Commission decision 2002/657/EC. Results show that 60% of the analysed samples were not contaminated by any residue, while 12% presented a concentration higher than the MRLs for tetracyclines, sulphonamides, quinolones, and macrolides. Results revealed that chicken were the most contaminated by antimicrobial residues, when compared to beef and milk. The obtained results demonstrate the uncontrolled use of antimicrobials in some Lebanese farms and claim for better management of livestock.     

Systematics study through scanning electron microscopy; a tool for the authentication of herbal drug Mentha suaveolens Ehrh

In all over the world, herbal drugs are usually adulterated with similar species or varieties due to incorrect identification. Most of herbal products devoid purity and quality, therefore an attempt was carried out to identify plant species and authenticate its herbal drug products from Mentha suaveolens. Microscopy tools provide an excellent platform to identify plants at species level. In this study, microscopic and pharmacokinetic parameters of M. suaveolens were observed. Plant species were collected from high diverse areas of Northern Pakistan. Macro and micro‐morphology including palynology and anatomical features were analyzed to study M. suaveolens. Species characteristics were studied, while implementing microscopic techniques for the delimitation and identification of the species. Traditionally Mentha species are used to cure several diseases that is, digestive disorders, respiratory disorders. Micromorphology (stem, leaves, flowers structure, length etc.), palynology (shape, size of pollen etc.), and anatomical characters (types of stomata, epidermal cell shape, and trichomes) were studied. Micromorphology and anatomical characters were of great interest and significance to discuss the taxonomy of the species. Taxonomic characters were studied to characterize and authenticate the species. The aim of the present study is to observe in detail the taxonomic identification of the species in term of morphology, palynology, and foliar epidermal anatomy for the correct identification along with their medicinal uses in the area.     

An investigation into physicochemical characteristics of ash produced from combustion of oil palm biomass wastein a boiler

Ash derived from combustion of Malaysian oil palm biomass (empty fruit bunches consisting of fibers) was physically and chemically characterized in order to provide a comprehensive understanding of its specific properties in terms of toxicity, compositions and reusability. Principal analyses conducted include particle size distribution, scanning electron microscopy, elemental dispersive X-ray, elemental analysis, toxicity characteristic leaching procedure (TCLP) as well as thermogravimetric, X-ray diffractometry and Fourier-transform infrared analyses. TCLP result indicated that the oil palm ash (OPA) should not be classified as toxic wastes in terms of heavy metal leachability since leachable copper, cadmium, lead and nickel concentrations were detected below the stipulated leachability limits. It was determined that the OPA contained high amount of potassium as well as presence of silica which implied its suitability to be reused as crude fertilizer or cement replacement material.     

优化移动多媒体传输链的功耗

消费者对于移动多媒体的需求是毫无疑问的，满足这些需求的技术已经开发成功，对于设计人员而言，剩下的问题就是如何利用这些技术，并将成功的产品带入市场。本文将讨论如何减省移动多媒体设备内关键元件的功耗，此外也会对现今移动多媒体设备设计人员所面对的工程挑战作出概括的分析，并就目前及新涌现的硅技术，提出可克服这些工程挑战的解决方案。     

Zooplankton population in the river tigris: Effects of samarra impoundment

The influences of the Samarra impoundment on the ecology of the downstream sector of the river Tigris are investigated. Zooplankton were collected monthly from July 1987 to July 1988. It was found that zooplankton were most abundant during high river discharges in March. During the month of low river discharge, September, the zooplankton population was greatly reduced immediately below the barrage and remained so to the last downstream station. Several factors seem to explain such differences. The high discharge from the impoundment was found to be the dominating factor and may flush the small backwaters in which zooplankton were abundant, thus increasing the population in the river. Zooplankton species vary in their ability to sustain populations in the river, variations which are due mainly to species-specific characteristics.     

Electrical Insulation Characteristics of Silicone and EPDM Polymeric Blends. I

The typical parts of a polymeric insulator are core, metal end fittings and polymeric housing material. The housing is intended to protect the fibre glass rod from the environment and electrical surface discharges. Since the housing materials are made of organic polymeric material, its insulation characteristics need to be studied. Amongst the many different polymers available, this work focuses on silicone rubber and ethylene propylene diene monomer (EPDM). Blends of EPDM and silicone rubber are prepared in a two roll mixing mill. Dicumyl peroxide is used as vulcanizing agent. The blends consisting of various proportions of component polymers are prepared, compression moulded into sheets, and post cured. The blends are tested for their insulation characteristics as per IEC and ASTM standards. Volume and surface resistivity, dielectric strength, dielectric constant, tan delta, tracking resistance, arc resistance, comparative tracking index, tensile strength, and percentage elongation at break of the blends are studied and discussed. The test results show that the increasing proportion of silicone enhances the electrical insulation properties whereas increasing weight percentage of EPDM improves the mechanical strength of the blends.