Volumetric out-of-furnace heat treatment of 3600-M3 decomposers

Specifications require that all the welds in 12-m-diam. decomposers with a capacity of 3600 m³ be subjected to high-temperature tempering before going into service in order to alleviate the stresses from the welding operation. Specialists at the organizations VNIIPTkhimnefteapparatury and VNIImontazhspetsstroi have proposed out-of-furnace volumetric (complete) of the assembled decomposer with the use of special heaters. The use of this heating method has shortened assembly operations while providing the welds with a highquality heat treatment and reducing the stresses overall (including welding stresses, stresses from assembly of the decomposer, etc.) The technology ensures uniform heating of the housing of the decomposer and provides for close control over the process. The experience gained in heat-treating decomposers can also be used in the construction of other containers that come into contact with corrosive media. __________ Translated from Metallurg, No. 3, pp. 61–64, March, 2006.     

Surface space-charge waves in open guiding structures

Basic definitions related to the main electrodynamic characteristics of surface space-charge waves are formulated. These characteristics and their relationships with the geometric dimensions of guiding structures (a dielectric cylinder and a planar metal-dielectric waveguide) are determined.     

The effect of photon energy and temperature on the persistent tunneling photoconductivity effect in Al/δ(Si)-GaAs structures

The phenomenon of persistent tunneling photoconductivity was studied using the tunneling spectroscopy technique at liquid-helium temperature: the separation between the unoccupied levels in a δ-doped layer at the GaAs surface decreased after illumination. This decrease was due to an increase in the width of the quantum well of the δ-doped layer. For photon energies hv exceeding the GaAs band gap E _g , this increase in the width of the quantum well was related to the accumulation of positive charge in the depth of GaAs induced by the generation of the electron-hole pairs and photoionization of deep centers. For hv < E _g (including the case of CO₂ laser), only photoionization is important. The experimental data agree with the self-consistent calculations. The critical temperature for the effect has been determined (T _c = 45 K); at higher temperatures, the effect disappears.     

Spontaneous and stimulated emission from CdxHg1−x Te semiconductor films

The experimental data on observation of spontaneous and stimulated emission from thin epitaxial Cd_xHg_1?x Te films optically pumped by Nd: YAG laser radiation are reported. A simple theoretical model is suggested to describe the initiation of population inversion under these conditions. The parameters realized under the experimental conditions are theoretically estimated.     

Protecting local access telecommunications networks: Toward a minimum-cost solution

The problem of designing fibre-optic networks for local-access telecommunications generates (at least) three non-trivial subproblems. In the first of these subproblems one must determine how many fibre-optic cables (fibres) are required at either end of a street. In the next subproblem a minimum-cost network must be designed to support the fibres. The network must also provide distinct paths from either end of the street to the central exchange(s). Finally, the fibre-optic cables must be placed in protective covers. These covers are available in a number of different sizes, allowing some flexibility when covering each section of the network. In this paper we describe a dynamic programming (DP) formulation for finding a minimum-cost (protective) covering for the network (the third of the subproblems). This problem is a generalised set covering problem with side constraints and is further complicated by the introduction of fixed and variable welding costs. The DP formulation selects covers along each arc (in the network), but cannot exactly model the fixed costs and so does not guarantee optimality. We also describe an integer programming (IP) formulation for assessing the quality of the DP solutions. The cost of the networks constructed by the IP model is less than those designed using the DP model, but the saving is not significant for the problems examined (less than 0.1%). This indicates that the DP model will generally give very good solutions. Furthermore, as the problem dimensions grow, DP gives significantly better solution times than IP.     

1/f noise in large-area Hg<Subscript>1−x</Subscript>Cd<Subscript>x</Subscript>Te photodiodes

The 1/f noise in photovoltaic (PV) molecular-beam epitaxy (MBE)-grown Hg_1−xCd_xTe double-layer planar heterostructure (DLPH) large-area detectors is a critical noise component with the potential to limit sensitivity of the cross-track infrared sounder (CrIS) instrument. Therefore, an understanding of the origins and mechanisms of noise currents in these PV detectors is of great importance. Excess low-frequency noise has been measured on a number of 1000-μm-diameter active-area detectors of varying “quality” (i.e., having a wide range of I-V characteristics at 78 K). The 1/f noise was measured as a function of cut-off wavelength under illuminated conditions. For short-wave infrared (SWIR) detectors at 98 K, minimal 1/f noise was measured when the total current was dominated by diffusion with white noise spectral density in the mid-10⁻¹⁵A/Hz^1/2 range. For SWIR detectors dominated by other than diffusion current, the ratio, α, of the noise current in unit bandwidth i_n(f = 1 Hz, V_d = −60 mV, and Δf = 1 Hz) to dark current I_d(V_d = −60 mV) was α_SW-d = i_n/I_d ∼ 1 × 10⁻³. The SWIR detectors measured at 0 mV under illuminated conditions had median α_SW-P = i_n/I_ph ∼ 7 × 10⁻⁶. For mid-wave infrared (MWIR) detectors, α_MW-d = i_n/I_d ∼ 2 × 10⁻⁴, due to tunneling current contributions to the 1/f noise. Measurements on forty-nine 1000-μm-diameter MWIR detectors under illuminated conditions at 98 K and −60 mV bias resulted in α_MW-P = i_n/I_ph = 4.16 ± 1.69 × 10⁻⁶. A significant point to note is that the photo-induced noise spectra are nearly identical at 0 mV and 100 mV reverse bias, with a noise-current-to-photocurrent ratio, α_MW-P, in the mid 10⁻⁶ range. For long-wave infrared (LWIR) detectors measured at 78 K, the ratio, α_LW-d = i_n/I_d ∼ 6 × 10⁻⁶, for the best performers. The majority of the LWIR detectors exhibited α_LW-d on the order of 2 × 10⁻⁵. The photo-induced 1/f noise had α_LW-P = i_n/I_ph ∼ 5 × 10⁻⁶. The value of the noise-current-to-dark-current ratio, α appears to increase with increasing bandgap. It is not clear if this is due to different current mechanisms impacting 1/f noise performance. Measurements on detectors of different bandgaps are needed at temperatures where diffusion current is the dominant current. Excess low-frequency noise measurements made as a function of detector reverse bias indicate 1/f noise may result primarily from the dominant current mechanism at each particular bias. The 1/f noise was not a direct function of the applied bias.     

Characteristics of planar diodes based on heavily doped GaAs/AlAs superlattices in the terahertz frequency region

Characteristics of ohmic InGaAs contacts in planar diodes based on semiconductor superlattices with a small-area active region (1–10 μm²) are studied. The diodes were formed on the basis of short (18 or 30 periods) heavily doped (10¹⁸ cm⁻³) GaAs/AlAs superlattices with a miniband width of 24.4 meV. The reduced resistance of the ohmic contact was equal to 2×10⁻⁷ Ω cm² at room temperature. It is shown that the properties of fabricated planar diodes make it possible to use these diodes later on in semiconductor devices that operate in the terahertz frequency region in a wide temperature range (4–300 K). __________ Translated from Fizika i Tekhnika Poluprovodnikov, Vol. 38, No. 9, 2004, pp. 1141–1146. Original Russian Text Copyright ? 2004 by Pavel’ev, Demarina, Koshurinov, Vasil’ev, Semenova, Zhukov, Ustinov.     

Photosensitivity of surface barrier structures based on Cu(In,Ga)Se<Subscript>2</Subscript> films grown by codeposition in vacuum

Polycrystalline Cu(In,Ga)Se₂ (CIGS) films with various ratios of Cu, In, and Ga were grown by codeposition of all elements in vacuum. The X-ray diffraction study showed that the films are single-phase and possess a chalcopyrite structure with predominant [112] orientation. The films exhibited a mirror smooth surface and had a close-packed structure composed of crystallites with clear faceting and a transverse size of 0.1–0.3 μm. Related surface barrier structures of the (In,Ag)/Cu(In,Ga)Se₂ type were obtained and their spectra of the quantum efficiency of photoconversion were studied. The obtained structures can be used for optimization of the CIGS film technology.     

Photoemission of polarized electrons from InAlGaAs/GaAs superlattices with minimum conduction band offsets

Photoemission of polarized electrons from heterostructures based on InAlGaAs/GaAs superlattices with minimum conduction-band offsets is investigated. The comparison of the excitation energy dependence of the photoemission polarization degree with the calculated spectra make it possible to determine the polarization losses at different stages of the photoemission. A maximum polarization of P = 91% and a quantum yield of 0.14% are close to the best results obtained for photocathodes on the basis of strained semiconductor superlattices.