A new MMIC broadside coupler using an array of air-bridges for directivity enhancement

A new quadrature broadside coupler is proposed, which employs an array of air-bridges to enhance directivity via its phase-equalization effect on the c-mode and /spl pi/-modes. The realization of air-bridges follows a standard MMIC fabrication process. An experimental chip fabricated on the 75-/spl mu/m GaAs substrate verifies the air-bridge effect and shows wideband characteristics of the coupling of 3.2/spl plusmn/0.4 dB, the insertion loss of 3.9/spl plusmn/0.4 dB, the output phase deviation from quadrature less than 6/spl deg/, and the isolation greater than 18 dB from 20 to 40 GHz.     

Test data compression and test time reduction using an embedded microprocessor

Systems-on-a-chip (SOCs) with many complex intellectual property cores require a large volume of data for manufacturing test. The computing power of the embedded processor in a SOC can be used to test the cores within the chip boundary, reducing the test time and memory requirements. This paper discusses techniques that use the computing power of the embedded processor in a more sophisticated way. The processor can generate and reuse random numbers to construct test patterns and selectively apply only those patterns that contribute to the fault coverage, significantly reducing the pattern generation time, the total number of test applications and, hence, the test time. It can also apply deterministic test patterns that have been compressed using the characteristics of the random patterns as well as those of the deterministic patterns themselves, which leads to high compression of test data. We compare three fast run-length coding schemes which are easily implemented and effective for test-data compression. We also demonstrate the effectiveness of the proposed approach by applying it to some benchmark circuits and by comparing it with other available techniques.     

A graphic approach to performance analysis of multistage linear interference canceller in long-code CDMA systems

The signal-to-interference-plus-noise-ratio performance of the multistage linear parallel and successive interference cancellers (LPIC and LSIC) in a long-code code-division multiple-access system is analyzed using a graphical approach. The decision statistic is modeled as a Gaussian random variable, whose mean and variance can be expressed as functions of moments of R for the LPIC and L for the LSIC, respectively, where R is the correlation matrix of signature sequences and L is the strict lower triangular part of R. Since the complexity of calculating these moments increases rapidly with the growth of the stage index, a graphical representation of moments is developed to facilitate the computation. Propositions are presented to relate the moment calculation problem to several well-known problems in graph theory, i.e., the coloring, the graph decomposition, the biconnected component finding, and the Euler tour problems. It is shown that the derived analytic results match well with simulation results.     

复合材料压缩破坏模式的缺陷敏感性

本文基于弹塑性分叉理论研究单向纤维增强复合材料的压缩破坏模式和压缩强度对缺陷的敏感性问题。对于常见复合材料,所得结论是:无缺陷或者小缺陷情况的破坏模式为倾斜破坏带;大缺陷情况的破坏模式为水平破坏带;形成水平破坏带的压力值小于形成倾斜破坏带的压力。     

Output probability from a general combinational network

In this paper, we present the method which calculates the probability of the output of a general combinational network being 1, when the probabilities is given for each input being 1. Also we present the method which derives the output probability expression in terms of a given set of input probabilities.The method is based on a basic probability axiom and Binary Decision Diagrams. A Boolean function for a combinational network is transformed into a Binary Decision Diagram and the output probability expression is derived from it. Therefore a derivation of the output probability for a combinational network can be straightforward. Some examples are showed that the method using Binary Decision Diagrams is simple and efficient. We can see a variation of the output probability for a combinational network according to the given set of input probabilities.     

Two-level optimal output feedback stabilizer design

Design of two-level system stabilizers is considered using an optimal reduced-order model whose state variables are torque angles and speeds. The reduced-order model retains their physical meaning and is used to design a two-level linear feedback controller that takes into account the realities and constraints of the electrical power systems. The two-level control strategy is used, and a global control signal is generated from the output variables to minimize the effect of interaction. The effectiveness of this controller is evaluated, and an example, the multimachine system, is given to illustrate the advantages of the proposed method. The responses of the system with the two-level scheme and optimal reduced order scheme are included for comparative analyses     

Effect of the Liquid-Phase Characteristic on the Microstructures and Dielectric Properties of Donor- (Niobium) and Acceptor- (Magnesium) Doped Barium Titanate

Changes in the microstructure and dielectric properties with the variation of the donor/acceptor ratio in BaTiO₃ ceramics were investigated. In donor-rich specimens, a liquid that appeared during sintering did not penetrate into grain boundaries. However, in the acceptor-rich specimens, the grains were separated by a liquid film during sintering. The much higher mobility of the liquid film than that of the grain boundaries was suggested to cause extensive grain growth in acceptor-rich BaTiO₃. The macroscopic homogenization of dopants because of grain growth in acceptor-rich specimens resulted in changes in the dielectric properties.     

Scaling laws and internal structure for characterizing electrospun poly[(R)-3-hydroxybutyrate] fibers

Using chloroform/dimethylformamide (CF/DMF) co-solvent, electrospinning of poly[(R)-3-hydroxybutyrate] (PHB) solutions was carried out at ambient temperature. The effects of the applied voltage (V), flow-rate (Q), and solution viscoelastic properties on the Taylor cone, electrified jet, and fiber morphology were investigated. In addition, the electric field developed by the needle-plate electrode configuration was calculated using a finite element analysis to reveal the tip-to-collector (H) effect. Among the processing parameters (V, Q and H), it was found that Q played a key role in determining the jet diameter (d_j) and electrospun fiber diameter (d_f), and scaling laws existed between them, i.e., d_j-Q^0.61 and d_f-Q^0.33. The diameter reduction ratios of D_o/d_j (D_o is the needle diameter) and d_j/d_f were measured as 50-120 and 5-10, respectively; it suggested that major jet stretching took place in the straight electrified jet region, and further chain orientation could be gained by the subsequent process of jet whipping. By changing PHB concentrations from 5 to 15 wt%, the solution viscosity (η_o) was increased from 100 to 4900 cP, whereas the surface tension and solution conductivity remained unchanged; it provided a good model solution to exclusively reveal the η_o effect on the electrospinning process. Our results showed that the η_o-dependence of d_j and d_f also followed simple scaling laws: d_j-η_o^0.06, and d_f-η_o^0.39, with a prefactor depending on the processing variables, mainly the flow-rate. Regardless of the PHB concentrations used, the obtained PHB fibers showed a similar crystallinity fraction of ca. 0.63 and possession of major α-crystals together with a small amount of β-crystals with zigzag chain conformation.     

The Fabrication and Characterization of Single‐Component Polymeric White‐Light‐Emitting Diodes

By using Ni⁰‐mediated polymerization, we have systematically synthesized a series of fluorene‐based copolymers composed of blue‐, green‐, and red‐light‐emitting comonomers with a view to producing polymers with white‐light emission. 2,7‐Dibromo‐9,9‐dihexylfluorene, {4‐(2‐[2,5‐dibromo‐4‐{2‐(4‐diphenylamino‐phenyl)‐vinyl}‐phenyl]‐vinyl)‐phenyl}‐diphenylamine (DTPA), and 2‐{2‐(2‐[4‐{bis(4‐bromo‐phenyl)amino}‐phenyl]‐vinyl)‐6‐tert‐butyl‐pyran‐4‐ylidene}‐malononitrile (TPDCM) were used as the blue‐, green‐, and red‐light‐emitting comonomers, respectively. It was found that the emission spectra of the resulting copolymers could easily be tuned by varying their DTPA and TPDCM content. Thus with the appropriate red/green/blue (RGB) unit ratio, we were able to obtain white‐light emission from these copolymers. A white‐light‐emitting diode using the polyfluorene copolymer containing 3 % green‐emitting DTPA and 2 % red‐emitting TPDCM (PG3R2) with a structure of indium tin oxide/poly(3,4‐ethylenedioxythiophene):poly(styrene sulfonic acid)/PG3R2/Ca/Al was found to exhibit a maximum brightness of 820 cd m^–2 at 11 V with Commission Internationale de L'Eclairage (CIE) coordinates of (0.33,0.35), which are close to the standard CIE coordinates for white‐light emission (0.33,0.33).