Propagation Delay of an RC-Chain With a Ramp Input

In this brief, two simple semi-analytical models which allow the estimation of the propagation delay of an RC-chain with a linear input are presented. The closed-form models can be used to evaluate the propagation delay of wires in modern VLSI and ULSI processes. The two approximations, a continuous function and a piecewise function, exhibit a maximum error lower than 15% at the end of the chain. The models have been validated extensively through circuit simulations. In particular, 1000 different RC-chains have been considered and simulated demonstrating the accuracy of the proposed models with respect to the most widely used Elmore delay metric     

New Class of High-<Emphasis Type="Italic">T</Emphasis><Subscript>C</Subscript> Diluted Ferromagnetic Semiconductors Based on CaO without Transition Metal Elements

We propose new-type ferromagnetic semiconductors based on CaO and K₂S without any transition metal elements. These materials show transparent and half-metallic ferromagnetism if the deep-impurity-band width (W) induced by doping of C, N, Si, or Ge impurities, and the electron-correlation energy (U) satisfy the Stoner’s condition of highly correlated electron system (U>W). Based on our first-principles calculations, we demonstrate that these materials satisfy the Stoner’s condition, and could be new candidates for transparent and half-metallic DMSs.     

Urinary leukotriene E4 and 11-dehydrothromboxane B2 in patients with aspirin-sensitive asthma

The objective of this study was to define the participation of cysteinyl leukotrienes (LTs) or thromboxane A2 in the pathogenesis of aspirin-sensitive asthma (ASA). Leukotriene E4 (LTE4) and 11-dehydrothromboxane B2 (11DTXB2) values in spot urine were measured in 22 asthmatics with a history of aspirin sensitivity and in 17 without such a history (non-aspirin-sensitive asthma [NASA]) in the outpatient clinic. The urinary LTE4 value was significantly higher in ASA patients than in NASA (340 +/- 47 vs 65 +/- 15 pg/mg.cr, P < 0.001), but there was no significant difference in urinary 11DTXB2 between the two groups (891 +/- 77 vs 657 +/- 90 pg/mg.cr). A high value of LTE4 was not associated with type of asthma, severity of disease, oral prednisolone treatment, sex, or age. A higher value of 11DTXB2 was observed in the atopic type than the nonatopic type in ASA (1086 +/- 111 vs 697 +/- 147 pg/mg.cr, P < 0.05). No correlation was observed between urinary LTE4 and 11DTXB2 in either ASA or NASA. In conclusion, LTs may play an important role in the pathogenesis of ASA, and TXA2 in the pathogenesis of the atopic type in ASA.     

Mechanism of welding fume suppression during AC-pulsed MIG welding of Al-Mg alloys

Welding fume, inevitably generated during arc welding processes, may be a source of occupational pneumoconiosis when persistently inhaled in the long term and accordingly merits serious consideration in occupational hygiene respects. To improve the working environment at welding sites, it is imperative to ensure total air exchange at work sites, local extraction in the vicinity of welding facilities, and the wearing of respiration protection devices in other respects.¹ Currently available preventive measures, however, suffer from a number of drawbacks, such as heavy investments needing to be made in equipment and facilities and operability being obstructed by the wearing of respiration protection devices. Alongside such passive measures, it is desirable to develop welding materials or methods able to suppress welding fume generation at source.     

The effects of warmth and CO2 concentration,with and without bioeffluents,on the emission of CO2 by occupants and physiological responses

The emission rate of carbon dioxide (CO₂) depends on many factors but mainly on the activity level (metabolic rate) of occupants. In this study, we examined two other factors that may influence the CO₂ emission rate, namely the background CO₂ concentration and the indoor temperature. Six male volunteers sat one by one in a 1.7 m³ chamber for 2.5 h and performed light office-type work under five different conditions with two temperature levels (23 vs. 28°C) and three background concentrations of CO₂ (800 vs. 1400 vs. 3000 ppm). Background CO₂ levels were increased either by dosing CO₂ from a cylinder or by reducing the outdoor air supply rate. Physiological responses to warmth, added CO₂, and bioeffluents were monitored. The rate of CO₂ emission was estimated using a mass-balance equation. The results indicate a higher CO₂ emission rate at the higher temperature, at which the subjects were warm, and a lower emission rate in all conditions in which the background CO₂ concentration increased. Physiological measurements partially explained the present results but more measurements are needed.     

Resuspension and settling of helminth eggs in water: Interactions with cohesive sediments

Helminth parasite eggs in low quality water represent main food safety and health hazards and are therefore important indicators used to determine whether such water can be used for irrigation. Through sedimentation helminth eggs accumulate in the sediment, however resuspension of deposited helminth eggs will lead to increased concentration of suspended eggs in the water. Our study aimed to determine the erodibility (erosion rate and erosion threshold) and settling velocity of Ascaris and Trichuris eggs as well as cohesive sediment at different time points after incorporation into the sediment. Cohesive sediment collected from a freshwater stream was used to prepare a sediment bed onto which helminth eggs were allowed to settle. The erodibility of both sediment and helminth eggs was found to decrease over time indicating that the eggs were incorporated into the surface material of the bed and that this material was stabilized through time. This interaction between eggs and bulk sediment was further manifested in an increased settling velocity of suspended eggs when sediment was present in the suspension as compared to a situation with settling in clean water. The incorporation into the sediment bed and the aggregation with sediment particles decrease the mobility of both helminth egg types. Our findings document that helminth eggs should not be viewed as single entities in water systems when modelling the distribution of eggs since both erodibility and settling velocity of eggs are determined by mobility of the sediment present in the water stream. Recalculation of the erosion threshold for helminth eggs and sediment showed that even at relatively low current velocities i.e. 0.07-0.12 m s⁻¹ newly deposited eggs will be mobile in open irrigation channels. These environmental factors affecting resuspension must be taken into account when developing models for sedimentation of helminth eggs in different water systems.     

Phase diagram study of Fe-Zn intermetallics

There are various intermetallic compounds in the Fe-Zn system. The phase diagram of this system is very important for understanding the surface structure of zinc-coated steel; therefore, equilibrium phases and their stable compositions must be known. The bulk samples of the Fe-Zn binary intermetallic compounds were synthesized by lengthy heat treatment for over 7.2×10⁵ s at 450 °C after 1.7×10⁵ s at 850 °C. The X-ray diffraction (XRD) patterns of samples kept for various periods at 450 °C were observed to determine the optimal heat treatment period, and the sample of Θ₁, which requires the longest time to form of all of the Fe-Zn binary intermetallic compounds, was obtained by the 7.2×10⁵ s heat treatment. Chemical composition of the samples was examined and X-ray diffraction was applied to ensure the formation of the intermetallic compounds. The results were in agreement with the literature on the Fe-Zn binary phase diagram.     

Design Procedures for Three-Stage CMOS OTAs With Nested-Miller Compensation

Design procedures for three-stage CMOS operational transconductance amplifiers employing nested-Miller frequency compensation are presented in this paper. After describing the basic methodology on a Class-A topology, some modifications, to increase swing, slew-rate and current drive capability, are subsequently discussed for a Class-AB solution. The approaches developed are simple as they do not introduce unnecessary circuit constraints and yield accurate results. They are hence suited for a pencil-and-paper design, but can be easily integrated into an analog knowledge-based computer-aided design tool. Experimental prototypes, designed in a 0.35-mum technology by following the proposed procedures, were fabricated and tested. Measurement results were found in close agreement with the target specifications