New intramolecular effect observed for polyesters: An anomeric effect

A series of polyesters was prepared to evaluate hydrolytic stability as a function of cyclohexyl dibasic acid content. The three cyclohexyl dibasic acids: 1,2; 1,3; and 1,4 were formulated into polyesters with two glycols. The proportion of cis and trans isomers was evaluated via ¹H NMR. The hydrolytic stability of short chain polyesters was evaluated in an acetone/water mixture which solubilized the polyesters to mimic oligoester behavior within a thermosetting polyester coating environment. The rate of hydrolysis was monitored by acid titration and corroborated by GPC. Surprisingly, 1,2-cylohexyl diacid-based polyesters were robust, and 1,3-cyclohexyl diacid-based polyesters were the most susceptible to hydrolysis. Evidently, a 1,2-anchimeric effect for cyclohexyl dibasic acid polyesters was not an important consideration, while the 1,3-cyclohexyl ester interaction was. Consequently, an anomeric effect was proposed. Presented at the 81st Annual Meeting of the Federation of Societies for Coatings Technology, November 12–14, 2003, in Philadelphia, PA.     

Structure evolution of conductive polymer composites revealed by solvent vapor induced time-dependent percolation

The authors of this paper synthesized a series of amphiphilic triblock copolymers of polystyrene-b-poly(ethylene glycol)-b-polystyrene (PS-PEG-PS) having different PEG/PS ratios with nearly identical molecular weights of the entire copolymers. The interfacial interactions in the composites consisting of carbon black and the copolymers can thus be tailored. When these conducting composites are exposed to certain solvent vapors, their electrical resistances greatly increase, showing the gas sensitivity. The present work indicated that this switching behavior is controlled by the structural relaxation of the composites because matrix swelling acts as the main mechanism. The response time has been correlated with absolute temperature by Arrhenius equation, and the estimated activation energy reflects mobility of the fillers involved in the solvent induced expansion of the surrounding polymer. Therefore, by using the gas sensibility of the conductive composites, the structure evolution of the composite materials in solid state and the effect of filler/matrix interfacial interaction on the relaxation property of the matrix polymer has been inspected. It was found that lower activation energy represents stronger interfacial interaction in case good solvent of the matrix was used for the test.     

Failure mechanism study of anisotropic conductive film (ACF) packages

Anisotropic conductive film (ACF) consists of an adhesive polymer matrix with dispersed conductive particles. In flip-chip technology, ACF has been used in place of solder and underfill for chip attachment to glass or organic substrates. The filler particles establish the electrical contacts between the interconnecting areas. ACF flip-chip bonding provides finer pitch, higher package density, reduced package size and improved lead-free compatibility. Nevertheless, the interconnection is different from traditional solder joints, the integrity and durability of the ACF interconnects have major concerns. Failures in anisotropic conductive film (ACF) parts have been reported after temperature cycling, moisture preconditioning and autoclave. The failures have not been well understood and have been attributed to a wide variety of causes. This paper investigates the failure mechanism of ACF using finite element simulation. From a failure-initiation point of view, the response of ACF packages to environmental (temperature and humidity) exposure is very different from standard underfilled packages. These differences cause the ACF package to fail in different ways from an underfilled package. Simulation results have shown that moisture-induced ACF swelling and delamination is the major cause of ACF failure. With moisture absorption, the loading condition at the interface is tensile-dominant, which corresponds to lower interface toughness (or fracture resistance). This condition is more prone to interface delamination. Therefore, the reliability of ACF packages is highly dependent on the ACF materials. The paper suggests a new approach toward material selection for reliable ACF packages. This approach has very good correlation with experimental results and reliability testing of various ACF materials.     

Error Concealment Based on Semantic Prioritization with Hardware‐Based Face Tracking

With video compression standards such as MPEG‐4, a transmission error happens in a video‐packet basis, rather than in a macroblock basis. In this context, we propose a semantic error prioritization method that determines the size of a video packet based on the importance of its contents. A video packet length is made to be short for an important area such as a facial area in order to reduce the possibility of error accumulation. To facilitate the semantic error prioritization, an efficient hardware algorithm for face tracking is proposed. The increase of hardware complexity is minimal because a motion estimation engine is efficiently re‐used for face tracking. Experimental results demonstrate that the facial area is well protected with the proposed scheme.     

高度有序多孔氧化铝模板的制备工艺与生长机制的研究

采用二次氧化法制备出高度有序的多孔氧化铝模板，结合扫描电镜和原子力显微镜对其结构、形貌进行观察和表征。研究了铝箔预处理和温度等对多孔氧化铝模板孔洞有序性的影响，讨论了有序孔洞的自组织生长机理。     

基于二维直方图分析的二元子图微光图像增强处理

提出了基于二维直方图分析的二元子图微光图像增强处理算法，根据原始图像的二维直方图分布特征，依据相邻像素的相关性数据，将图像分割成二元子图像，对每个子图像分别进行直方图均衡增强处理，最后合成得到完整的处理图像，通过用信息容量等图像评价参数对实验结果进行分析，表明此算法克服了对整幅图像进行直方图均衡时难以把握局部细节的缺点，得到了具有较好视觉质量的处理后微光图像。     

Structural properties of 0.65Pb(Mg1/3Nb2/3)O3–0.35PbTiO3 relaxor ferroelectric thin films on SrRuO3 conducting oxides

Coating of 0.65Pb(Mg_1/3Nb_2/3)O₃–0.35PbTiO₃ (PMN–PT) relaxor ferroelectrics by a sol–gel method is followed by growth of epitaxial SrRuO₃ (SRO) metallic oxide electrodes on SrTiO₃ (STO) single-crystal substrate by pulsed laser deposition. High-quality PMN–PT films on SRO with preferred growth orientation were successfully fabricated by controlling the operation parameters. Structural properties of relaxor ferroelectric PMN–PT thin films on SRO/STO substrates have been studied by X-ray diffraction (XRD), transmission electron microscopy (TEM) and atomic force microscopy (AFM). In-plane and out-of-plane alignments of the heterostructure are confirmed and the structural twinning of the materials are also revealed.     

Nickel and chromium cycles: Stocks and flows project part IV

Nickel and chromium are essential ingredients in alloys increasingly important for energy-efficient, environmentally friendly modern technology. Quantitative assessment of the flows of these metals through the world economy from resource extraction to final disposal informs resource policy, energy planning, environmental science, and waste management. This article summarizes the worldwide technological cycles of nickel and chromium in 2000. Stainless steel is the major use of these metals, but they serve numerous other special needs, as in superalloys for high-temperature service, as plating materials, and in coinage. Because they are used primarily in alloys, novel recycling issues arise as their use becomes more widespread. “... the great New York and St. Louis double track, nickel plated railroad...” — Norwalk, Ohio, Chronicle 10 March 1881 announces arrival of surveyors for the future Nickel Plate Railway “Later [1911] I formed an alloy of Iron and Chromium, which showed remarkable resistance to rust and tarnish ... [It was] rediscovered by an Englishman named Brearley, in 1914.” —Elwood Haynes to Stephen F. Roberts, 17 January 1925     

Study on Contamination Control for Yield Enhancement in the Manufacturing Line of Cellular Phone Modules

Practical studies on the method of contamination control for yield enhancement in the cellular phone modules production line were carried out. A contamination control method was proposed, consisting of data collection, data analysis, improvement action, verification, and implementation of control. The partition check method and the composition analysis for data collection and data analysis were respectively used in the cellular phone modules manufacturing process, and these methods were evaluated by the variation of yield loss before and after implementing the actions for improvement. In the partition check method, the critical process step was selected, and yield loss reduction through improvement actions was observed, whereas in the composition analysis, critical sources were selected, and yield loss reduction through improvement actions was investigated. From the results, it is concluded that the partition check and the composition analysis are effective solutions for contamination control in cleanroom production lines.