Calibrating high-vacuum gauges

Translated from Izmeritel'naya Tekhnika, No. 6, pp. 19–20, June, 1989.     

Craze yielding and fracture mechanism in PE/PS/PE laminated films

The change in polystyrene (PS) layer thickness, which has been simultaneously determined during post-yield deformation, shows that crazing is the basic mechanism of toughening in all laminated films, and that shear deformation supplements the contribution of crazing especially for samples with high polyethylene (PE) volume fractions. Crazes formed in PS layers in the laminated films are slender and regular compared with the short and lenticular crazes formed in bulk PS film. When PE volume fraction increased, craze advance speed decreased because of the reduction of the stress concentration effect at craze tips. The life-time of the first mature craze to be formed at a given strain rate increased with PE volume fraction because the PE supporting the mature crazes could effectively inhibit craze rupture and blunt out the propagating crack by absorbing the stored elastic energy in the PS layer that would have been dissipated as fracture surface energy.     

Influence of initial growth layer and Ti underlayer on magneticproperties and recording characteristics of very thin films ofevaporated Co-Cr media

A Co-Cr film deposited directly on a substrate has an initial growth layer with low coercivity. However, the existence of a Ti underlayer prevents the formation of such a layer. As a result, Co-Cr film deposited on a Ti underlayer has high perpendicular anisotropy and coercivity even in cases of extremely thin film thickness (200 Å). As for the read-write characteristics of Co-Cr thin-film media, the existence of such an initial growth layer greatly improves the reproduced output level. The cause for this is considered to be that the free charges which appear on the back surface of the perpendicular recording layer are reduced and the demagnetization field acting on the recorded magnetization subsequently decreases due to the existence of the initial growth layer     

Effects of manufacturing defects on the mechanical properties of carbon fibre reinforced polyethersulphone laminates

The effects of defects on the mechanical properties of carbon fibre reinforced polyethersulphone laminates have been measured. The defects studied were cut fibre plies, omission of polymer films and local delamination produced by the inclusion of foreign matter. Of these it was found that only cut plies had a significant detrimental effect on the strength of a laminate. For specimens with two cut plies, the failure stress, tensile, flexural and compressive in the remaining continuous plies was the same as in the defect-free material, provided that the cut plies were widely separated. However the failure stresses were 15–18% lower in the continuous plies in the specimens containing two cut plies which were more closely spaced and in specimens containing four cut plies.     

Imperfections and impurity phases in flux grown RCrO3 (R = La,Yb) single crystals

Results of scanning electron microscopy (SEM) and energy dispersive X-ray analytical (EDAX) investigations, conducted on some elevated structures displayed by flux grown rare earth orthochromite, RCrO₃ (R = La, Yb) crystals, are presented. The peculiar structures exhibited by crystal surfaces indicate imperfections and impurity phases. EDAX of elevated structures reveals the various phases to be composed of lead associated materials which may probably be either Pb₂CrO₅ or Pb₂OF₂ (flux). Other secondary crystallization of impurity phases, ROF (R = La, Yb) is illustrated in the case of RCrO₃ (R = La, Yb) crystals. The elevated structures illustrate their non-stoichiometric behaviour. Precipitation of impurity phases and formation of imperfections during the growth of RCrO₃ (R = La, Yb) crystals and their effect on the crystalline quality is discussed.     

Influence of ash deposits on the heat resistance of materials for gas turbine engine blades

Leningrad. Translated from Problemy Prochnosti, No. 1, pp. 71–76, January, 1989.     

Near-resonance oscillations of a nonsymmetric nonlinear system with a crack

The Malkin method, which was developed to construct a single unique resonance solution of nonlinear equations, is generalized for the case of the derivation of all stationary solutions in the near-resonance zone, and also for transient oscillations.Kiev Polytechnic Institute. Translated from Problemy Prochnosti, No. 10, pp. 108–112, October, 1989.     

Fuel modelling in fast reactor whole core accident calculations

Transient fuel pin behaviour and fuel motion models are of major importance for the analysis of the initiation phase of unprotected whole-core LOF and TOP accidents in LMFBRs. The role played by these models is highlighted by discussing LOF and TOP accident sequences. This is followed by an overview of present whole-core fuel pin behaviour and fuel motion models and also a critical evaluation of these models.     

Power spectral density of CMI-coded TV signal transmitted through fibre-optic heterodyne system

An expression is derived for the power spectral density of a coded mark inversion (CMI) TV signal transmitted through a fibre-optic heterodyne system. An illustrative example is given, and its power spectral density has been computed numerically.