Improvement of strength distribution inside slab concrete by vacuum dewatering method

The strength and hardness of concrete slab surface is considered significantly affected by bleeding of concrete. It has been reported that dewatering by vacuum processing is quite effective to obtain high density of concrete. The method, however, has not been successfully used for the concrete work in the field of building construction, compared with that of civil engineering works in Japan. In the present study, firstly the state of the art concerning vacuum dewatering method is reviewed and the newly improved vacuum dewatering method is introduced. Then the effect of the proposed method on concrete properties of slab is examined by a series of experiments in order to find more reasonable and effective way in the application of the proposed method.     

Strengthening and Toughening of Silicon Nitride by Superplastic Deformation

Mechanical properties of silicon nitride which was superplastically deformed in plane-strain compression were investigated. Superplastically deformed silicon nitride exhibited a highly anisotropic microstructure, where rod-shaped grains tended to be aligned along the extruding direction. The bending strength and fracture toughness were increased substantially by the deformation process when a stress was applied in the extruding direction. It appears that these improvements were mainly due to effective operation of grain bridging and pull-out by the grain alignment.     

Improved Filtration Performance of Continuous Alumina-fiber-reinforced Mullite Composites for Hot-Gas Cleaning

The effect of filtration layer morphology on filtration performance at 673 K was investigated for continuous alumina-fiber-reinforced mullite composite filters that capture fly ash on their outer surfaces. Two types of filtration layers were prepared on the outer surfaces: a mono-layer consisting of mullite agglomerated particulates and a bi-layer, with mullite whiskers formed by a vapor-phase reaction and strongly adhered to the particulates exposed on the outer surfaces. For filters with mono-filtration layers, the filtration efficiency was improved slightly by increasing the filtration layer thickness. However, the maximum differential pressure increased during the filtration tests. Adhesion of whiskers to the outer surface decreased the maximum differential pressure to about one-third less than that with the mono-filtration layer. This low differential pressure remained constant throughout the duration of the test, with corresponding increases in filtration efficiency.     

Titanium aluminide coating on titanium surface using three-dimensional microwelder

Feasibility of a new method of titanium aluminide coating on titanium surface based on a reaction between aluminum liquid beads and the surface of titanium substrate has been studied using a computer-aided three-dimensional microwelder (3DMW) designed by the present authors. A predetermined length of thin aluminum wire was fed onto the substrate surface, and a spark was stricken from a thin electrode of a W-Ce₂O₃ alloy to make a small aluminum liquid bead on the substrate surface and to simultaneously melt a small area of the substrate surface beneath the bead. All conditions including the length of the wire feeding, the position of the electrode, electric power, etc. had been programmed beforehand. The liquid bead containing aluminum and titanium rapidly solidified on the titanium substrate surface producing titanium aluminides on it. Repetition of the aluminum wire feeding, the electrode positioning and the spark striking produced a coating layer consisting of sub-layers of TiAl₃, TiAl and Ti₃Al from the surface side to the substrate side. Vickers hardness and wear resistance of the coated sample were remarkably improved.     

Group Symmetry in Interior-Point Methods for Semidefinite Program

A class of group symmetric Semi-Definite Program (SDP) is introduced by using the framework of group representation theory. It is proved that the central path and several search directions of primal-dual interior-point methods are group symmetric. Preservation of group symmetry along the search direction theoretically guarantees that the numerically obtained optimal solution is group symmetric. As an illustrative example, we show that the optimization problem of a symmetric truss under frequency constraints can be formulated as a group symmetric SDP. Numerical experiments using an interior-point algorithm demonstrate convergence to strictly group symmetric solutions.     

Environmental stress cracking of poly(acrylonitrile-butadiene-styrene)

The environmental stress cracking (ESC) of acrylonitrile-butadiene-styrene (ABS) copolymer caused by a non-ionic surfactant (poly-oxyethylene alkylether) was studied by constant-load tensile creep tests and edge crack tension (ECT) tests. The fracture surfaces were investigated by a scanning electron microscope (SEM) and the morphology of the crack tip was investigated by a transmission electron microscope (TEM). It was found that the results of the creep tests performed in the non-ionic surfactant were very different from those performed in air. SEM images of the fracture surfaces showed that there were three different mechanisms of fracture and that specimens had a tendency to rupture by ESC when the stress was small. The results of the ECT tests and the TEM images showed that the change in the mechanism of the fracture was attributable to the change of morphology at the crack tip.     

Design of robotic behavior that imitates animal consciousness

A 6-degrees-of-freedom serial arm hand is controlled to move toward an object in an unseen environment. We developed a consciousness-based architecture (CBA), which is a hierarchical human development model representing the relationship between consciousness and behavior and is used for imitating a human groping action. During forward motion toward the object, a robot arm hand can help to avoid obstacles from which the robot collects contact information. The CBA organizes such information to learn a path plan for backward motion to the origin without contact with the obstacles. Experimental results show that the CBA successfully extends the hand to the goal while avoiding any obstacle. This work was presented in part at the 12th International Symposium on Artificial Life and Robotics, Oita, Japan, January 25–27, 2007     

Relationship between Expression of Onco-Related miRNAs and the Endoscopic Appearance of Colorectal Tumors

Accumulating data indicates that certain microRNAs (miRNAs or miRs) are differently expressed in samples of tumors and paired non-tumorous samples taken from the same patients with colorectal tumors. We examined the expression of onco-related miRNAs in 131 sporadic exophytic adenomas or early cancers and in 52 sporadic flat elevated adenomas or early cancers to clarify the relationship between the expression of the miRNAs and the endoscopic morphological appearance of the colorectal tumors. The expression levels of miR-143, -145, and -34a were significantly reduced in most of the exophytic tumors compared with those in the flat elevated ones. In type 2 cancers, the miRNA expression profile was very similar to that of the exophytic tumors. The expression levels of miR-7 and -21 were significantly up-regulated in some flat elevated adenomas compared with those in exophytic adenomas. In contrast, in most of the miR-143 and -145 down-regulated cases of the adenoma-carcinoma sequence and in some of the de novo types of carcinoma, the up-regulation of oncogenic miR-7 and/or -21 contributed to the triggering mechanism leading to the carcinogenetic process. These findings indicated that the expression of onco-related miRNA was associated with the morphological appearance of colorectal tumors.     

Structurally Diverse Polyamines: Solid‐Phase Synthesis and Interaction with DNA

A versatile solid‐phase approach based on peptide chemistry was used to construct four classes of structurally diverse polyamines with modified backbones: linear, partially constrained, branched, and cyclic. Their effects on DNA duplex stability and structure were examined. The polyamines showed distinct activities, thus highlighting the importance of polyamine backbone structure. Interestingly, the rank order of polyamine ability for DNA compaction was different to that for their effects on circular dichroism and melting temperature, thus indicating that these polyamines have distinct effects on secondary and higher‐order structures of DNA.