Enhanced catalytic activity of nanoshell carbon co-doped with boron and nitrogen in the oxygen reduction reaction

The use of carbon cathode catalysts in polymer electrolyte fuel cells instead of the current platinum catalysts is attracting increasing attention. We claim that two factors are important for enhancing the activity of carbon cathode catalysts in the oxygen reduction reaction (ORR): the formation of a nanoshell structure and co-doping with boron and nitrogen. Herein, we investigate the preparation and characterization of active ORR carbon catalysts that combine the above factors. Boron and nitrogen (BN)-doped nanoshell-containing carbon (BN-NSCC) was prepared by carbonizing a mixture of poly(furfuryl alcohol), cobalt phthalocyanine, melamine, and a trifluoroborane–methanol complex at 1000 °C. Transmission electron microscopy and X-ray photoelectron spectroscopy revealed the formation of nanoshell structures with distorted graphitic layers and the introduction of boron and nitrogen atoms, respectively. The ORR activity was evaluated in oxygen-saturated 0.5 mol dm^?3 H₂SO₄ using Koutecky–Levich analysis. The BN-NSCC showed an eight to ten times higher ORR activity than undoped NSCC, with an increased number of electrons participating in the reaction. Tafel analysis revealed a change in the rate-determining step caused by BN-doping. Thus, the combination of a nanoshell structure and co-doping with boron and nitrogen was found to improve the ORR activity of carbon catalysts.     

Evaluation of standing‐sitting support system with passive rotational seat mechanism in standing motion

Since a decrease in muscle mass of elderly people, the physical burden of them in standing‐sitting motion of a seat are increasing than young people. For this problem, several standing‐sitting support systems have been developed, and evaluations of these systems focusing on a reduction of physical load have been discussed. However, these evaluations are of support systems with an active actuators or of support systems when they use a handrail and a standing aid. Thus, an evaluation of a support system with only passive actuators has not been reported. In this paper, in standing motion with using a standing‐sitting support system with passive rotational seat mechanism which our group proposes, we objectively evaluate an effectiveness of the passive rotational seat mechanism by statistical analysis.     

Fabrication of BSCF-based mixed oxide ionic-electronic conducting multi-layered membrane by sequential electrophoretic deposition process

The Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3-δ (BSCF)-based multi-layered oxygen separation membrane was fabricated by the sequential electrophoretic deposition (EPD) process. A thin porous/dense bi-layer of BSCF was formed on a thick porous support of BSCF. The porous support prepared by a sacrificial template method using BSCF powder mixed with wheat starch (30 wt%) as a pore-forming agent, followed by uniaxial pressing and low-temperature sintering, was directly used as an EPD electrode. A thin BSCF layer was first formed on the porous support, and then a thin BSCF + PMMA (polymethyl methacrylate) layer was sequentially formed on the thin BSCF layer using a bimodal suspension of BSCF and PMMA. A 30-μm thin porous/dense bi-layer of BSCF of which the total thickness was obtained by optimizing the processes of EPD and subsequent co-sintering. The oxygen separation performance of 3.7 ml (STP) min^?1 cm^?2 at 860 °C was achieved for the BSCF-based multi-layered oxygen separation membrane.     

An order acceptance strategy under limited engineering man-hours for cost estimation in Engineering–Procurement–Construction projects

Accurate cost estimation is essential for any Engineering–Procurement–Construction (EPC) contractor accepting profitable projects because the project price is determined prior to receiving the contract. Therefore the contractor needs to ensure engineering man-hours (MH) in order to estimate project costs accurately as well as carry out the accepted orders. In this paper, we develop MH based order acceptance strategies and investigate their effects on the total expected profit through a long-term operation in EPC projects under a competitive bidding situation. To this end we build a simulation model describing relations among the volume of MH for cost estimation, accepted orders, revenues, and profits in EPC projects. Using our model, we show that the strategy, which maintains the appropriate balance of MH for cost estimation and project execution under the variability of accepted orders with competitive bidding situations, improves the total expected profit in EPC projects.     

Source identification of nitrous oxide on autotrophic partial nitrification in a granular sludge reactor

Emission of nitrous oxide (N₂O) during biological wastewater treatment is of growing concern since N₂O is a major stratospheric ozone-depleting substance and an important greenhouse gas. The emission of N₂O from a lab-scale granular sequencing batch reactor (SBR) for partial nitrification (PN) treating synthetic wastewater without organic carbon was therefore determined in this study, because PN process is known to produce more N₂O than conventional nitrification processes. The average N₂O emission rate from the SBR was 0.32 ± 0.17 mg-N L⁻¹ h⁻¹, corresponding to the average emission of N₂O of 0.8 ± 0.4% of the incoming nitrogen load (1.5 ± 0.8% of the converted NH₄⁺). Analysis of dynamic concentration profiles during one cycle of the SBR operation demonstrated that N₂O concentration in off-gas was the highest just after starting aeration whereas N₂O concentration in effluent was gradually increased in the initial 40 min of the aeration period and was decreased thereafter. Isotopomer analysis was conducted to identify the main N₂O production pathway in the reactor during one cycle. The hydroxylamine (NH₂OH) oxidation pathway accounted for 65% of the total N₂O production in the initial phase during one cycle, whereas contribution of the NO₂⁻ reduction pathway to N₂O production was comparable with that of the NH₂OH oxidation pathway in the latter phase. In addition, spatial distributions of bacteria and their activities in single microbial granules taken from the reactor were determined with microsensors and by in situ hybridization. Partial nitrification occurred mainly in the oxic surface layer of the granules and ammonia-oxidizing bacteria were abundant in this layer. N₂O production was also found mainly in the oxic surface layer. Based on these results, although N₂O was produced mainly via NH₂OH oxidation pathway in the autotrophic partial nitrification reactor, N₂O production mechanisms were complex and could involve multiple N₂O production pathways.     

Correlations of Hepatic Hemodynamics,Liver Function,and Fibrosis Markers in Nonalcoholic Fatty Liver Disease: Comparison with Chronic Hepatitis Related to Hepatitis C Virus

The progression of chronic liver disease differs by etiology. The aim of this study was to elucidate the difference in disease progression between chronic hepatitis C (CHC) and nonalcoholic fatty liver disease (NAFLD) by means of fibrosis markers, liver function, and hepatic tissue blood flow (TBF). Xenon computed tomography (Xe-CT) was performed in 139 patients with NAFLD and 152 patients with CHC (including liver cirrhosis (LC)). The cutoff values for fibrosis markers were compared between NAFLD and CHC, and correlations between hepatic TBF and liver function tests were examined at each fibrosis stage. The cutoff values for detection of the advanced fibrosis stage were lower in NAFLD than in CHC. Although portal venous TBF (PVTBF) correlated with liver function tests, PVTBF in initial LC caused by nonalcoholic steatohepatitis (NASH-LC) was significantly lower than that in hepatitis C virus (C-LC) (p = 0.014). Conversely, the liver function tests in NASH-LC were higher than those in C-LC (p < 0.05). It is important to recognize the difference between NAFLD and CHC. We concluded that changes in hepatic blood flow occurred during the earliest stage of hepatic fibrosis in patients with NAFLD; therefore, patients with NAFLD need to be followed carefully.     

Characterization of the Oxide Scale Formed on T12 Water Wall Tube After Long-term Service in Supercritical Power Plant

Oxidation of Metals - Oxide scale control is one of the critical maintenance issues in fossil fuel power plant. Hence, the water treatment of the feed water has been changed from all-volatile...     

Advanced synthesis for monodisperse polymer nanoparticles in aqueous media with sub-millimolar surfactants

Highly monodisperse polystyrene nanoparticles with mean diameters of less than 100 nm are synthesized via aqueous emulsion polymerization using an amphoteric initiator (VA-057) in the presence of sub-millimolar concentrations of anionic surfactant. Since the net charge on the initiator is almost zero at neutral pH, the resultant latex particle size is mainly determined by surfactant adsorption. Polymerizations were performed in the presence of a range of anionic surfactants with differing critical micelle concentrations (CMC) by varying the concentrations of surfactant, initiator and monomer, and also the ionic strength. Sodium dodecyl benzene sulfonate (SDBS), sodium hexadecyl sulfate (SHS), and sodium octadecyl sulfate (SOS) have relatively low CMCs and so enable formation of highly monodisperse nanoparticles at relatively low (sub-millimolar) surfactant concentrations, C_S (i.e. below the CMC in each case). Empirically, it was found that the particle number, N_p, and coefficient of variation of the particle size, C_V, were strongly dependent on the C_S/CMC ratio: N_p increased almost in proportion with the square of this ratio, while the C_V exhibited a minimum at approximately C_S/CMC = 0.20. Higher ionic strength reduced the particle size, which is consistent with the above relationship because the addition of salt lowers the CMCs of ionic surfactants. Polymer latex particles produced using such formulations form highly regular, close-packed colloidal arrays.     

A method to modify coordinates of detectors in positron emission tomography systems

A new method to modify coordinates of detectors in any positron emission tomography (PET) system using a radioactive point source is developed. This method is based on selecting a centered detector in each detector block of PET and measuring coincidence counts between the two centered detectors in opposite detector blocks to find the coordinates of their LOR (Line of Response). Due to slight misalignment of detector positions, measured LORs may not intersect at a single point. Based on the proposed method, the coordinates of detectors can be measured with very high accuracy and the coordinate of the center of the gantry (which is normally the same as the center of field of view) can be defined correctly. The results of the application of our method to a small animal PET system (FinePET), which was recently developed at Tohoku University, Japan, are shown here. The method is expected to contribute to the design and development of PET systems which can realize a very high spatial resolution of less than 1 mm FWHM.     

Numerical Study of the Performance of a Regenerative Furnace

In the present study, the numerical simulation of reactive turbulent flow and heat transfer in a regenerative gas-fired furnace has been carried out to investigate its performance. The effects of geometric and operating conditions on the performance of the furnace have also been studied. A moment closure method with an assumed g probability density function for mixture fraction is used in the present work to model the turbulent nonpremixed combustion process in the furnace. A comparison is made between the predicted results and the experimental data.