Formation of linear aldehydes during surface water preozonization and their removal in water treatment in relation to mutagenic activity and sum parameters

Low molecular weight aldehydes were formed during surface water preozonization, their levels showing a positive correlation with increasing ozone dose applied and with increasing water temperature. A strong negative correlation was observed between aldehyde levels and U.V. absorbance at 254 nm.Coagulation had no influence on the aldehydes present and the influence of rapid double layer filtration varied strongly with temperature : significant removals were only observed above 10°C.Mutagenic activity generated by preozonization in Salmonella typhimurium TA98 shows an ozone dose depending relationship different from the formation of linear aldehydes. Its removal by coagulation is not effective but rapid double layer filtration reduces mutagenic activity to marginal levels.In this respect too no clear parallel can be drawn between the presence of low molecular weight aldehydes and mutagenic activity.     

Quality of Crude Fish Oil Extracted from Herring Byproducts of Varying States of Freshness

ABSTRACT: Herring byproducts were stored at 2 and 15 °C for up to 72 h. Over time, significant increases of total volatile bases (TVB), histamine, putrescine, cadaverine, and tyramine were detected. However, only tyramine and TVB levels were temperature-dependent. The level of total polyunsaturated fatty acids (PUFAs) was constant. Longer byproducts storage gave rise to an oil with higher levels of free fatty acids, eicosapentaenoic acid (EPA), docosahexaenoic acid (DHA), and total PUFAs, while fluorescent compounds were lower. A higher storage temperature led to oil higher in α-tocopherol and EPA levels and lower in anisidine value. Surprisingly, the oil with the highest content of PUFAs was not produced from the freshest byproducts, and oil with low oxidation products can be extracted from stored byproducts.     

Instructional texts rewritten by five expert teams: Revisions and retention improvements.

700 undergraduates were tested in 3 experiments on original or rewritten versions of 52 instructional texts about Army job tasks, general science, philosophy, and history. Five experts had rewritten various sets of the texts and stated hypotheses about the efficacious features of their revisions. We tested their hypotheses and several others. Recall and recognition tests were given immediately and after a 24-hr delay. Results showed that revisions made by 3 of the 5 experts improved retention of text information. The kind and number of revisions and improvements varied across the text sets. Most expert hypotheses were not supported, and they made many revisions they were declaratively unaware of. Some of our hypotheses about the revision features were supported, but different features were effective for different sets of texts. It was concluded that some experts have effective knowledge about improving instructional text, but it exists primarily in procedural form. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Effect of orienting fields on agglomeration in dilute dispersions of magnetic fine particles

Static light scattering was used to investigate dilute dispersions of fine gamma -Fe/sub 2/O/sub 3/ magnetic particles. The particles were acicular and on average 0.39 mu m long and 0.056 mu m in diameter. They were dispersed in organic solvents at concentrations of approximately 10/sup -4/ vol%, corresponding to an average interparticle separation of 9 mu m. Computer programs using a coupled dipole algorithm to predict the scattering from the particles were written. Experimental results do not agree with computer calculations of the light scattering from single particles, but are consistent with scattering from thick ropelike agglomerates of particles. The size of these agglomerates was estimated after 10 s to be less than 100 particles, while the thickness of the ropes is at least 5 particles.<>     

Hydrogen adsorption studies in micro-size cobalt dots

Hydrogen desorption curves were obtained from a sample composed of a square arrangement of Co dots with average diameter of 4.4 μm, separated by a distance of 11.6 μm. A macroscopic sample of Co dots grown on a 2.5 × 2.5 cm Si substrate was made by standard lithographic techniques and used in these experiments. Thermal programmed desorption (TPD) was performed under ultra-high vacuum conditions. Hydrogen TPD curves were obtained from a 1 × 1 cm Co dots samples displaying a maximum of intensity at 425 K. Hydrogen TPD curve was also obtained from 1 cm× 1 cm samples of Co films and Co foils for comparison. The hydrogen TPD curves have decreasing intensity from the Co foils to the Co dots and finally to the Co films. This indicates that there are more sites for hydrogen adsorption on the Co dots than in the Co films. This is a surprising result because there is approximately 8.7 times less Co atoms exposed in the Co dots that in the Co film sample. A desorption energy of 27 kcal/mol was obtained for the Co dots suggesting that hydrogen is adsorbed on an hcp hollow site of the Co dot crystalline structure.     

The hypersonic environment: Required operating conditions and design challenges

Hypersonic flight powered by airbreathing engines offers the potential for faster response time at long ranges, and reduced cost for access-to-space. In the present paper the operating environment of typical hypersonic vehicles are discussed, including results for the radiation equilibrium wall temperature of external vehicle surfaces and the flow properties through three sample engines spanning the range of hydrocarbon-fueled Mach 4-8 flight and hydrogen-fueled flight at speeds up to Mach 17. Flow conditions at several locations through the sample engines were calculated to provide indications of the required operating flow environment. Additional system consideration such a seals, joints, vehicle integration and in-service engineering are addressed.     

From biological inspiration toward next-generation manipulators: manipulator control focused on human tasks

This paper presents our approach to extend the niche of behavior-based robotics toward manipulation. We use results from neuroscience to derive some qualitative design rules for the mechanics of the manipulator, resulting in a next-generation manipulator, the "soft arm". By defining the basic behaviors of the manipulator as trajectory-producing behaviors (which is also biologically plausible), we have designed a first test case: writing on a board with a mobile manipulator. The soft arm has not yet been developed; therefore, we have emulated such a soft robot arm on an industrial robot.     

Spectrally pure excitation signals: only a dream?

For accurate testing of a nonlinear device-under-test (DUT), the spectral purity of the input signal is utterly important. This paper describes a method to create very pure signals, such as sine waves, dual-tones, or multitones, using only power measurements. The signals are generated with an arbitrary waveform generator. Any unwanted spectral line is removed, independent of its exact origin. This allows to apply the correct signal to the DUT, even if the signal source is not perfect or is followed by filters or amplifiers with a small nonlinear distortion. Measurements are used to demonstrate the capabilities of the method.     

Stability studies on methyl and ethyl fatty acid esters of sunflowerseed oil

Fatty acid esters, high in linoleic acid, were prepared and stored for long-term engine tests. Storage tests with these esters were undertaken to obtain more information on optimal storage requirements and general stability characteristics. Samples were kept at three temperature levels (20 C, 30 C and fluctuating around 50 C) for a 90-day period and were removed at regular intervals for chemical and physical analysis. The influence of air, temperature, light, TBHQ and contact with mild steel was evaluated by comparing the free fatty acid, peroxide, anisidine, ultraviolet absorption, viscosity and induction periods. A statistical model was used to evaluate the data and to reduce the large number of data points to comparable curves. Storage of esters in contact with air, especially at a temperature above 30 C, resulted in significant increases in peroxide, ultraviolet absorption, free fatty acid, viscosity and anisidine values. Exclusion of air retarded oxidation at all temperature levels. A direct relationship between viscosity increases and oxidation parameters was evident. Exposure to light caused a small increase in the oxidation parameters of esters stored at the highest temperature level. Addition of TBHQ prevented oxidation of samples stored under moderate conditions. Under unfavorable storage conditions the anti-oxidant was no longer effective. Mild steel had very little effect on the oxidation parameters. Only the anisidine values of samples stored at the highest temperature level were slightly increased. Methyl esters performed slightly better than ethyl esters during the storage test. The following practical guidelines for storage of fatty acid ester fuels are: (i) airtight containers should be used; (ii) the storage temperature should be <30 C; (iii) mild steel (rust free) containers may be used, and (iv) TBHQ has a beneficial effect on oxidation stability.