Bi-Pb-Tl三元系相图

用室温、高温X射线衍射及淬火的方法,测定了Bi-Pb-Tl三元系25℃的等温截面及该体系中的相结构。     

晶界碳化物对Fe-Cr15-Ni25合金蠕变裂纹扩展行为的影响SCIEI

在两种不同晶界状态下研究了Fe-Cr15-Ni25合金的蠕变裂纹扩展行为。单相合金的空洞在晶界三叉点处形核,而对晶界上有碳化物析出的合金,空洞在晶界碳化物上形核。晶界碳化物阻碍了空洞的长大和连接,因而大大提高了蠕变裂纹扩展抗力。     

激光合金化熔池成分均匀性与形状系数的关系SCIEI

本文研究了激光工艺参数对镀Cr中碳低合金钢激光合金化熔池形状系数及成分均匀性的影响。实验结果表明,熔池成分均匀性取决于其截面形状系数,后者是光束功率密度和交互作用时间的函数。在功率密度一定时,形状系数与交互作用时间成线性关系。当形状系数为1.6—3.0时,可以获得成分均匀的熔池。     

氢对Ti合金的Debye温度和晶格常数的影响

使用X射线衍射仪测定出不同氢含量的Ti-30Mo合金的Debye特征温度值以及晶格常数的变化,结果表明随着氢含量的增加,Debye特征温度相应地减小而晶格常数增加,证实了氢含量的增加会导致金属原子间键合力的减弱,从而造成金属脆化。     

EFFECT OF ALLOY ELEMENTS ON QUASIEQUILIBRIUM MICROSTRUCTURE IN Fe-Mn-Ni-Cr STEELS

The microstructures of Fe-Mn-Ni-Cr steels with medium carbon and the effect of alloy ele-ments on them have been investigated by means of X-ray diffraction quantitative phase ana-lyses,metallography and hardness tests.The volume fraction of martensite in steels quenchedat 1100℃ can be expressed as:f_M~(1100)=162.643-15.482Mn-7.36Ni-4.286(Cr+Mo+V)Based on this expression,the quasi-equilibrium microstructure diagram has been obtained.Itis shown that the effect of Mn on the austenite stability is greater than that of Ni.The equiva-lent [Ni]=2.104Mn+Ni and equivalent [Cr]=Cr+Mo+V.The driving force for martensite transformation at M_s point has been calculated to hedrastically decreased by element Mn.     

SOLUTION BEHAVIOUR OF VARIOUS ALLOYING ELEMENTS IN Ni_3Si

The solid solubilities of 15 common alloying elements added to the Ll_2-type intermetalliccompound Ni_3Si at 900°C have been estimated,and their substitution modes have been de-duced from the direction of solubility lobe of the compound.It is shown that the alloyingbehaviours in Ni_3Si are determined by both size and electronic factors,i.e.,the substitutionmode is governed by electronic configuration and solubility by the both.An interactionparameter is presented to describe quantitatively the influence of electronic configuration onsubstitution mode and the solubility limit can be successfully explained together with atom radius.     

二元Al-Li合金的沉淀反应SCIEI

本文通过对两种成分的二元Al-Li合金的硬度测量,DSC分析和TEM观察,研究了其沉淀过程。实验结果表明,在恒定时间时效,合金硬度与温度的关系曲线上在低温范围内有一峰值出现;在DSC曲线低温处有明显的回溶吸热峰,因此该合金低温时效有预沉淀(富Li GP区)形成。在较高温度时效,GP区不复存在;随着δ′相颗粒长大,合金硬度很快增加;DSC曲线上有两个δ′相回溶峰,它意味着δ′析出需有两次结构调整。平衡δ相借助晶界直接从过饱和固溶体中形核长大,其热稳定性较好。     

(Ⅰ+Ⅱ)复合型氢致开裂的研究

本文研究了30CrMnSiA高强钢在纯Ⅰ型、纯Ⅱ型和(Ⅰ+Ⅱ)复合型加载条件下的氢致开裂。实验表明,在1NH_2SO_4溶液中预充氢的试件在上述加载条件下均表现出氢致脆性。纯Ⅱ型氢致开裂门槛值K_(ⅡH)/K_(ⅡX)=0.27,与纯Ⅰ型门槛值K_(ⅠH)/K_(ⅠX)=0.29基本相同,而在K_Ⅱ/K_Ⅰ比值为0.27,0.4和0.81时,(Ⅰ+Ⅱ)复合型氢致开裂门槛值分别为0.36,0.41和0.37,表明纯Ⅰ型和纯Ⅱ型具有更高的氢脆敏感性。最后用自Ⅰ型加载向Ⅱ型过渡时,三轴张力和塑性变形程度这二个矛盾因素对氢致开裂的共同作用解释了上述实验结果。     

三角Марков链在重选中的应用

本文将Bagnold剪切理论与Марков过程理论结合起来,研究溜槽类重选设备的分选机理,根据矿粒的理论转移概率,建立了分选指标与给矿参数间的定量关系,并进一步利用细粒人工混合矿在摇动溜槽上的分选结果,验证了所得的数学模型。     

ELECTRON MICROANALYSIS FOR LASER MELTED ZONE IN 45 STEEL WITH Fe-Ni-Cr COATING

The Fe-Ni-Cr coating laver has been alloyed with 45 steel base metal by transverse.flow typeCO_2 gas laser of maximum output 5kW.The characteristics of the melted zone and the es-sence of the“bright band”has been investigated using the electron microscopy.The resultsshow that the“bright band”belongs to the melted zone and is a vertical section of the planecrystal,The width of the“bright band”equals the height of the plane crystal,which decreaseswith the increase of laser beam scanning rate and the decrease of laser power.This has beenexplained in terms of constitutional supercooling G/R.